A lossless transmission with characteristic impedance of Z0 = 1002 and length = 52cm The line was terminated with a load of Zy= 30 + j502. According to what is given, a) The reflection coefficient in the load and the voltage standing wave ratio on the line (GDDO) Find out. b) Find the impedance and admittance at the line input. (for f = 750MHZ) c) For f = 750MHZ, the impedance and admittance values 2cm away from the load. (It will be assumed that = 20.)

A lossless transmission with characteristic impedance of Z0 = 1002 and length = 52cm The line was terminated with a load of Zy= 30 + j502. According to what is given, a) The reflection coefficient in the load and the voltage standing wave ratio on the line (GDDO) Find out. b) Find the impedance and admittance at the line input. (for f = 750MHZ) c) For f = 750MHZ, the impedance and admittance values 2cm away from the load. (It will be assumed that = 20.)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For a lossless trabsmisison line, the characteristic impedance is 80 ohm. If the capacitance per unit length is 1.5 mh/m then what will be the inductance per unit length.
One circuit of a single-phase transmission line is composed of three solid 0.12" radius wires. The return circuit is composed of two 0.15" radius wires. Find the inductance of the complete line in mH/mi. The distance between wires are 40" horizontally and 25" vertically. A. 2.54 mH/mi B. 2.478 mH/mi C. 2.488 mH/mi D. 2.567 mH/mi Provide Clear Explaination
c) For a transmission line w/characteristic impedance Z0 = 50 W. At some point of the line, a forward wave has the voltage V+ = 10V and backward wave has the voltage V- = 4V. i) Currents of the forward wave and backward wave at that point. ii) Measured voltage and current at that point. d) A transmission line has the following properties: Length, L = 3 m. Characteristic impedance Z0 = 50 W. The load impedance ZL = 100 W. And phase constant b = p/3. Assume the forward voltage at z = 0 is VA =10ejp/4 At z = 3m, calculate: i) Forward voltage and forward current. ii) Backward voltage and backward current. iii) Measured (total) voltage and current across the load
The conductor of a single-phase 60-Hz line is a solid round aluminum wire having a diameter of 0.412 cm. The conductor spacing is 3 m. Determiņe the inductance of the line in millihenrys per mile. How much of the inductance is due to internal flux linkages? Assume skin effect is negligible.
Why the Capacitance effect is neglected in Short Transmission Line.
A 105MHz, 90 v peak signal is incident on a 50-ohm transmission line. The line is 125m long and is terminated in 300-ohm load. What is the SWR for this situation? Find the reflection coefficient.
The conductor of a single-phase 60-Hz line is a solid round aluminum wire having a diameter of 0.412 cm. The conductor spacing is 3 m. Determine the inductance of the line in millinery’s per mile. How much of the inductance is due to internal flux linkages? Assume skin effect is negligible.
A 702 high-frequency lossless line is used at a frequency where 2 = 80cm with a load of 140+j91 2 a. Calculate the reflection coefficient and the SWR b. Determine the distance to the first voltage minimum from the load c. Determine the distance to the first voltage maximum from the load d. Calculate the impedance at the point where maximum voltages occur
Expression for a voltage reflection co-efficient in terms of load impedance and characteristics impedance is: a) (ZL- Zo)/(ZL+ Zo) b) (Z+ Zo)/(ZL- Z) c) ZĻ. Zo/( Z+ Zo)( ZL-Zo) d) (ZL+ Zo)( ZL-Zo ZL. Zo
Three conductors for a 3-phase 60 Hz transmission line are placed in a horizontal plane with a separation between two conductors is D meters. The conductor geometrical mean distance is 2.0 cm. The line reactance is 0.486 ohm/kilometer. Find the phase conductor separation D
A single-phase transmission line consisting of two conductors, the radius of each conductor is 0.4 cm, the distance between the conductors is three and half meters and the height above ground is eight meter. Determine 1)The capacitance in uF/km without effect of ground 2)The capacitance in uF/km with effect of ground
g) Why the Capacitance effect is neglected in Short Transmission Line.