! A double riveted lab joint single strap (chain riveting) shown in the figure. Given that therivet diameter is 12 mm, the width of the strap is 150 mm, the strap thickness "s" is 10 mm,the pitch is 50 mm, and the margin "e" is 15 mm. Check the safety of the joint if thepermissible values of the stresses are:Tr = 140 MPa, Ora = 140 MPa, Ocr=280 MPa, t= 100 MpaF2-화+2d-e-F

A double riveted lab joint single strap (chain riveting) shown in the figure. Given that th rivet diameter is 12 mm, the width of the strap is 150 mm, the strap thickness "s" is 10 mn the pitch is 50 mm, and the margin "e" is 15 mm. Check the safety of the joint if th permissible values of the stresses are: t₁ = 140 MPa, Ora = 140 MPa, Ger=280 MPa, t= 100 Mpa F

A double riveted lab joint single strap (chain riveting) shown in the figure. Given that th rivet diameter is 12 mm, the width of the strap is 150 mm, the strap thickness "s" is 10 mn the pitch is 50 mm, and the margin "e" is 15 mm. Check the safety of the joint if th permissible values of the stresses are: t₁ = 140 MPa, Ora = 140 MPa, Ger=280 MPa, t= 100 Mpa F

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

The rubber band given below is subjected to the following tensile loading. Calculate the minimum thickness of the rubber (tr) and the minimum steel pin diameter (Dpin) so that the structure does not fail. Consider: Allowable tensile strength of the rubber= 20MPa Allowable shear strength of the steel = 200MPa Reflection: 1) How would you solve this problem if a Factor of Safety was given? 2) Are there any other dimensions worth calculating for the rubber belt?
Determine the design tensile strength of the plate (200 × 100) mm connected to a 12 mm thick gussets, using 20 mm bolts shown below, if the yield and ultimate stress of the steel used are 250 MPa and 420 MPa respectively, fy= 250 MPa fu= 450 MPa
A W18×86 beam is riveted tona W24×117 grinder by q connection as shown in the figure. The diameter of the rivets is 7/8 in, and angles are each 4×31/2×3/8 in. For each rivets assume that the allowable stresses are T= 15 ksi and stress in b is 32 ksi. What is the bearing strength of the grinder? What is the bearing strengtht of the beam? What is the shear strength of the rivets? What is the maximum load that the connection can carry?
The 10-mm-diameter steel bolt in (Figure 1) is surrounded by a bronze sleeve. The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. Est = 200 GPa, Ebr 100 GPa. Figure P P -10 mm -20 mm 1 of 1 Part A If the bolt is subjected to a compressive force of P = 21.9 kN, determine the magnitude of the average normal stress in the steel. Express your answer to three significant figures and include appropriate units. Ost = Submit Part B Obr = Submit 0 Value If the bolt is subjected to a compressive force of P = 21.9 kN, determine the magnitude of the average normal stress in the bronze. Express your answer to three significant figures and include appropriate units. Provide Feedback A Request Answer Value Units Request Answer Units ?
The angle L 8 x 8 x ½ in tension shown in the figure below must resist aservice dead load of 35 kips, live load of 50 kips, and a roof live load of 2kips. The steel used is A50 (Fy = 50 ksi, Fu = 65 ksi) and its welding length is 4”.Determine if the member has sufficient fracture and yield strength.
2. A steel plate is 360 mm wide and 20 mm thick with four bolts hole into the place as shown in the figure. Compute the following: a. Critical net area required by the NSCP specs. b. Max. critical net area required by the NSP specs. Note that, Max. net area is 85% of the critical net area Capacity of the joint if the allowable tensile stress is 0.75Fy. Use A36 steel Fy=248 MPa 25 mm= DIAMETER OF BOLTS 45 45mm fmmy C. 90mm 90mm 90mm Comm P
An A36 tension member shown in the figure is connected with three 19 mm diamter bolts. Diameter of hole = 22mm. Properties of 150 mm x 100 mm x 12.5 mm angle A = 3065 mm2 y = 50.55 mm Fy = 248 MPa Fu = 400 MPa Determine the desire strength due to fracture in the net section. Use U = 0.85 kN
A threaded round steel bar is subjected to a tota axial pull of 8000 lb. If the diameter of the unthreaded portion is 7/8 in., the unit stress in that portion is A. 10,470 psi B. 13,310 psi C. 16,230 psi D. 19,880 psi
1. The hanger assembly shown supports a 4500-kg pipe. The working stresses for each of the hanger assembly components are as follows: Tensile Stress in the Hanger Rod ≤ 140 MPa Shearing Stress in the bolt ≤80 MPa Bearing Stress between the bolt & the Bottom Strap ≤ 120 MPa Calculate the following: a. Required diameter of the hanger b. Required diameter of the bolt
The figure shows a plate having a width of 400 mm and thickness of 12 mm is to be connected to another plate by 34 mm diameter bolts as shown in the figure. Assume diameter of holes to be 2 mm larger than the diameter of the bolts. Use A 36 steel plate with yield strength Fy = 248 MPa and minimum tensile strength Fu = 400 MPa. For a chain holes extending across a part in any diagonal or zigzag line, the net width of the part shall be obtained by deducting from the gross width the sum of the diameters or slot dimensions of all holes in the chain and adding, for each gage space in the chain, the quantity S24g where S is the longitudinal center to center (pitch) of any consecutive holes, in millimetres and g is the transverse center to center spacing (gage) between fastener gage lines in millimetres. If a = 60 mm, c = 150 mm and d = 100 mm. Determine the nearest value of “b” so that the net width along bolts 1-2-3-4 is equal to the net width along bolts 1-2-4. Determine the nearest value…
Required information A square yellow-brass bar must not stretch more than 2.4 mm when it is subjected to a tensile load of 34 kN. Given: E= 105 GPa and that the allowable tensile strength is 104 MPa, determine (a) The allowable side length of the cross-section (b) is the allowable value a maximum or a minimum? Why? (c) The allowable length of the bar (d) is the allowable length a maximum or a minimum? (a&b) The allowable side length, for the square cross section, is given as [ (mm) and the value is a (Click to select)
The two wooden boards shown in the figure are connected by a 0.5 in. diameter bolt. Washers are installed under the head of the bolt and under the nut. The washer dimensions are D  2 in. and d 5/8 in. The nut is tightened to cause a tensile stress of 9,000 psi in the bolt. Determine the bearing stress MPa between the washer and the wood