A 3-phase, 60 Hz, six pole, 220-volt wound rotor induction motor has a stator that is connected in Delta and the rotor that is connected in Wye. The rotor has haft as many turns as that stator. the RR is equal to 0.1- ohm and XBR is equal to 0.5-ohm (a) calculate also the starting torque developed by the motor (b) For over all operation of this induction motor, calculate the efficiency based on the gathered data.

A 3-phase, 60 Hz, six pole, 220-volt wound rotor induction motor has a stator that is connected in Delta and the rotor that is connected in Wye. The rotor has haft as many turns as that stator. the RR is equal to 0.1- ohm and XBR is equal to 0.5-ohm (a) calculate also the starting torque developed by the motor (b) For over all operation of this induction motor, calculate the efficiency based on the gathered data.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 6RQ: Name three factors that determine the torque produced by an induction motor.

See similar textbooks

Similar questions

6- Which of the following supply is given to the rotor winding of 3-Phase Induction Motor: a) DC Supply b) AC Supply c) No Supply d) Pulsating Supply 7- 3-Phase Induction Motor will have Starting Torque and Starting Current a) High, High b) Low, Low. c) High, Low d) Low, High 8- Which of the following method is used for controlling the speed of an induction motor: a) Changing number of stator poles b) Supply voltage control c) Frequency control d) All the options are correct 9- Which of the following method cannot be used for starting of 3-Phase Squirrel Induction Motor: a) Star-Delta Starting b) Line resistor startling c) transformer Starter d) Rotor Resistance Starting 10- The rotor of a stepper motor has no: a) windings b) commutator c) brushes d) all of the above
An 8 pole, 50 Hz slip ring induction motor runs at a slip of 2.67% on full load. The rotor resistance per phase of the winding is 0.2 ohm. What external resistance per phase must be added in the rotor circuit so that the motor now runs ate a slip of 17.33% such that the torque remains same in both the cases. (Ans: 1.1 ohm)
A 110 V, 60 Hz, 6 – pole single phase induction motor 1/3 hp has the following equivalent circuit impedances: RI = 1.52 ohm, R2 = 3.13 ohm and x1 =2.10 ohm, x2 =1.56 ohm. Xm=58.2 ohm, The Friction, windage and stry losses =16W, the core loss = 35 W, For a slip of 0.05, calculation (a) input current, (b) power factor, (c) developed power, (d) output power, (e) speed (f) in put power (g) air gab power (h) T ind (i) T load 6) efficiency.
A four-pole induction motor drives a load at 2478 rpm. This is to be accomplished by using an electronic converter to convert a 400-V dc source into a set of three-phase ac voltages. Part A Find the frequency required for the ac voltages assuming that the slip is 4 percent. The load requires 2 hp. Express your answer to three significant figures and include the appropriate units. f= Submit Part B Value I = HA Request Answer Submit If the dc-to-ac converter has a power efficiency of 90 percent and the motor has a power efficiency of 80 percent, estimate the current taken from the dc source. Express your answer to three significant figures and include the appropriate units. HÅ Value Units Request Answer ? Units ?
A freewheeling DC motor is driven with 1000 rpm and a nominal load torque of 80Nm. The field circuit resistance is 200 and the armature circuit resistance is 0.2 O. The field coils are fed with a zero degree transmission angle through a single-phase fully controlled converter connected to a single-phase 240V source. The armature circuit is fed from a single phase 400V source through another fully controlled converter. Magnetic saturation has been neglected, the motor constant is given as 0.8 V - s / A - rad. Assuming that there is no fluctuation in armature and field current, find the control angle of the converter feeding the armature at nominal load. If you want to leave the question blank, click again on the option you marked.
What are the various losses in an induction motor? On what factors do they depend? IV. V. List the different types of stray load losses in an induction motor.
What is The efficiency of 3-ph induction motor. at (Is=4.5A, T=13 N.m, N=1333 rpm, Pph=864 watt ) ?
A 220 V DC series motor runs drawing a current of 30 A from the supply. Armature and field circuit resistances are 0.4 and 0.1 respectively. The load torque varies as the square of the speed. The flux in the motor may be taken as being proportional to the armature current. To reduce the speed of the motor by 50% the resistance in ohms that should be added in series with the armature is
7- A 6-pole, 50-Hz, 3-0 induction motor is running at 950 rpm and has rotor Cu loss of 6 kW. Its rotor input is......kW (a) 120 (b) 60 (c) 6.3 (d) 66 8- The number of slip rings on a squirrel cage induction motor is usually (a)Two (b) Three (c) Four (d) None
tørque in new Draw the power flow diagram of induction motor and explain the different power losses, the air gap power and the converted pòwer. Explain how by solving the equivalent circuit of three phase induction motor the input current, input power factor, air gap power, rotor copper loss, converted power, output power and induced torque are calculated. (b)A 440 V, 50 Hz, 2-pole, Y-connected induction motor is rated 75 KW. The equivalent circuit parameters are: R, = 0.0752 R, = 0.0652 X = 1.22 Pare = 1.1kW X, = 0.172 X, = 0.17Q Pe =150W PEAW = 1.0kW For a slip of 0.04 find the line-eurrent, the stator"power factor, the stator copper_loss, the air gap power, the converted power the induced torque and the Toad torque. MISC
A four-pole, three-phase induction motor drives aturbine load. At a certain operating point the machinehas 4 percent slip and 87 percent efficiency. The motordrives a turbine with torque–speed characteristic givenby TL = 20 + 0.006ω2. Determine the torque at themotor-turbine shaft and the total power delivered tothe turbine. What is the total power consumed by themotor?
c) What is the physical meaning for each of the following induction motor parameters: R1 „R2 ,Rc ,X1 ,X2 ,Xm ?