A 11 kV transmission line has the following line constants: A = 0.85 degree 5°, B=200 degree 75°. (a) Determine the power at unity power factor that can be received, if the voltage profile at each end is to be maintained at 11 kV. (b) What type of compensation equipment would be required if the load is 150 MW at unity of with the same voltage profile as in part (a).

A 11 kV transmission line has the following line constants: A = 0.85 degree 5°, B=200 degree 75°. (a) Determine the power at unity power factor that can be received, if the voltage profile at each end is to be maintained at 11 kV. (b) What type of compensation equipment would be required if the load is 150 MW at unity of with the same voltage profile as in part (a).

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.31P

See similar textbooks

Similar questions

Consider the oneline diagram shown in Figure 3.40. The three-phase transformer bank is made up of three identical single-phase transformers, each specified by X1=0.24 (on the low-voltage side), negligible resistance and magnetizing current, and turns ratio =N2/N1=10. The transformer bank is delivering 100 MW at 0.8 p.f. lagging to a substation bus whose voltage is 230 kV. (a) Determine the primary current magnitude, primary voltage (line-to-line) magnitude, and the three-phase complex power supplied by the generator. Choose the line-to-neutral voltage at the bus, Va as the reference Account for the phase shift, and assume positive-sequence operation. (b) Find the phase shift between the primary and secondary voltages.
4. An Open-Wye/Open-Delta transformer, as shown in Figure, is formed by two identical single-phase transformers. The primary line-to-line voltage is 12.47 kV, and the secondary line-to-line voltage is 208 V. Take
in distribution transformers; What is 30 degrees phase shift in delta-star connection? What are the disadvantages? (can you explain with drawing?)
What is load curve
The p.u. impedance value of an alternator corresponding to base values of 13.2 kV and 30 MVA is 0.2 p.u. Then the p.u. impedance value of an alternator for the new base values of 13.8 kV and 50 MVA is......
Here is a single phase transformer, 15 kVA, 15000/380 V, 50 Hz has Ze-0.02+j0.05 perunit, R. 50 perunit, and Xm =30 perunit, (per unit = actual value/base value), for scaling of the problem. (pu). A) Compute and draw the equivalent circuit components in Qs referred to the low-voltage side, B) Low voltage side is connected to a load of 4L 90° (lagging) and HV side is supplied by 15KV, compute voltage drop on the load V2 and voltage regulation VR.
6. A 5,000-kVA, 3-phase transformer, 6.6/33-kV, A/Y, has a no-load loss of 15 kW and a full-load loss of 50 kW. The impedance drop at full-load is 7%. Calculate the primary voltage when a load of 3,200 kW at 0.8 p.f. is delivered at 33 kV.
In the Transmission Line Simulator, the Transmission Line is composed of which parameter/s? O A. The Shunt Conductance Only O B. The Series Impedance and Shunt Capacitance O C. The Shunt Capacitance Only O D. The Series Impedance Only
A 60Hz sourcewith an effective voltage of 240 volts supplies 4500 volt-amp to a load with a p.f. of 0.75 lagging. Determine the parallel capacitance required to improve the power factor to: a) 0.9 lagging and b) 0.9 leading. What per cent reduction in line current resulted in part (a)?
In power distribution systems, what is sometimes necessary to install to reduce harmonic frequencies and distortion between the three-phase transformers and distribution panels?
A simple power system diagram is given below. The system consists of a 120/0 volt generator connected to an ideal 1:5 step up transformer, a transmission line, and ideal 10:1 step down transformer and a load. The impedance of the transmission line is 10 + j20, and the impedance of the load is 4+ j2 ohms. The base values for the system are chosen to be 120 volts and 10 KVA at the generator. a) Solve for the generator current lg using the per unit system. Do show your calculated per unit diagram. b) Solve for the value of the load voltage from the per unit system circuit. 10 n 20 n T: 10:1 ZLOAD = 4 + j2 120gv load
Which termination would result to a phase change of 180 degrees at the load if Zo = 100 ohm? a. 50 ohm b. short circuit c. 75 ohm d. all of these What is the purpose of impedance matching? a. maximum return loss b. maximum SWR c. maximum load power d. maximum reflection A short piece of transmission line that may be open or shorted and used for impedance matching purposes. a. converter b. decoder c. stub d. transformer