7.10 The hydraulic conductivity of a sand at a void ratio of 0.5 is 0.022 cm/sec. Estimate its hydraulic conductivity at a void ratio of 0.7. Use Eq. (7.31). 7.18 A layered soil is shown in Figure 7.31. Estimate the ratio of equivalent hydrau conductivity, kmeq/kvieg)- 1.5 m 1 m 1.5 m 1 m Ok = 2x 10-3 cm/sec (top layer) |k = 2 x 10-4 cm/sec k := 10-4 cm/sec k = 3x 10-4 cm/sec (bottom layer)

7.10 The hydraulic conductivity of a sand at a void ratio of 0.5 is 0.022 cm/sec. Estimate its hydraulic conductivity at a void ratio of 0.7. Use Eq. (7.31). 7.18 A layered soil is shown in Figure 7.31. Estimate the ratio of equivalent hydrau conductivity, kmeq/kvieg)- 1.5 m 1 m 1.5 m 1 m Ok = 2x 10-3 cm/sec (top layer) |k = 2 x 10-4 cm/sec k := 10-4 cm/sec k = 3x 10-4 cm/sec (bottom layer)

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter7: Permeability

Section: Chapter Questions

Problem 7.14P

See similar textbooks

Similar questions

Problem (5) A layered soil is shown in following figure. a) Estimate the hydraulic conductivity for flow in the vertical direction. b) Estimate the equivalent hydraulic conductivity for flow in horizontal direction. c) calculate the ratio of ky(eg) /kh(eq) 1 m k = 10-3 cm/sec 1 m k = 2 × 10-4 cm/sec 1 m k = 10 cm/sec 1 m k = 2 × 10¬³ cm/sec
CVE 331: Theoretical hydraulic conductivity calculation Problem 1: The hydraulic conductivity of a sandy sol is 7x10 cm/sec at void ratio 0.68. What is the hydraulic conductivity at void ratio 0.85 ? (o.re) A= 2,42e k2 ei Problem 2: The hydraulic conductivity of a clay soil is 121o* cm/sec at void ratio 0.56, and 3.1x10 cm/sec at void ratio 0.74. What is the hydraulic conductivity the soll at void ratio 0.65 ? e3 ki %3D - 3. 797 GRAIN SIZE DISTRIBUTION GRAPH. A- PROJECE
Problem 5 From the figure shown, the void ratio of the sand is 0.55 with a specific gravity of 2.68. The cross- sectional area of the tank is 0.5 m² and hydraulic conductivity of sand = 0.1 cm/s. 1. What is the rate of upward seepage in m3/hour? 2. Determine the critical hydraulic gradient for zero effective stress. 3. Determine the value of h to cause boiling. 4. Determine the value of x. h=1.2 m H₁=1 m z =0.8 H₂=2 m In flow Soil C B H₂O valve open K
be the hydraulic conductivity at 20°C? Ans. 1.0 x 10 cm/sec 4. For a normally consolidated clay, the following values are given. k(cm/sec) 0.45 x 10 e 0.78 1.1 0.88 x 10 Estimate k at a void ratio of 0.97 6.0089 107
From the figure shown, the void ratio of the sand is 0.55 with a specific gravity of 2.68. The cross-sectional area of the tank is 0.5 sq.m and hydraulic conductivity of sand = 0.1 cm/s. a. What is the rate of upward seepage in cu.m/hour? b.Determine the critical hydraulic gradient for zero effective stress. c. Determine the value of h (head loss) to cause boiling. NEED ASAP. THANK YOU.
1. (30 pts) The soil profile shown below consists of 10 meters of sandy silt overlying gravel. The pore water pressure at the top surface of the silty sand is zero and can be assumed to remain zero. a) Calculate the level to which water would rise in a piezometer tube inserted into the top of the gravel if the silty sand is just stable? Use submerged unit weights and seepage forces to arrive at your answer (do not calculate total stresses and pore water pressures). Express your answer as an elevation, e.g. "Elev. 130". (Note: Elevations are in meters) (10 pts) b) Using the piezometric elevation calculated in part (a), calculate the pore water pressure at the bottom of the silty sand if the silty sand is just stable (10 pts). c) Calculate the total stress at the base of the silty sand and show that it is equal to the pore water pressure calculated in part (b) (10 pts) Elev. 120 m. Elev. 110 m. Sandy Silt (saturated) Void ratio, e = 0.68 G = 2.65 Gravel
be the hydraulic conductivity at 20 Docs A20 pe 4. For a normally consolidated clay, the following values are given. k (cm/sec) 0.45 x 106 0.78 1.1 0.88 x 106 Estimate k at a void ratio of 0.97
From the figure shown, H₁ = 0.60, H₂ = 0.90 m. and h = 0.45 m. The sand has a saturated unit weight of 18.65 KN/m³. Hydraulic conductivity of sand K= 0.12 cm/sec. If the cross sectional area of tank = 0.46 m², determine the rate of upward seepage of water in liters /sec. h=0.45m T H₂=0.60 m H₂-0.90 m Direction of flow H₂O Sand ILGS G valve open
A falling head hydraulic conductivity test is performed on a sample of soil. The following values are given: Length of specimen = 8 in. • Area of soil specimen = 1.6 in^2 • Area of standpipe = 0.06 in^2 • Head difference at time t=0 = 20 in %3D • Head difference at time t=180 sec = 12 in a. Find the coefficient of permeability of soil b. Compute the rate of flow of water in the soil
The data from a falling-head test on a silty clay are: Cross sectional area of soil = 1000 mm^2 Length of soil sample = 200 mm Area of stand pipe = 40 mm^2 Head difference at time t = 0 is 500 mm Head difference at time t = 3 min is 300 mm a) Determine the hydraulic conductivity of the soil in cm/sec. b) What is the head difference at time t = 100 sec in mm
The results of a constant-head permeability test for a sand sample having a sectional area of 10000mm2 and a length of 200 mm are as follows: (1) Constant head difference 400mm (2) Time of collection of water = 30 seconds (3) Volume of water collected = 600 cm3. The hydraulic conductivity is: Oa. 1.0 mm/sec Ob. 1,7mm/sec c. 2.9 mm/sec O d. 0.5mm/sec
HYDRAULIC CONDUCTIVITY PROBLEM 1: The results of a constant head permeability test for a fine sand and sample having a diameter of 150 mm and a length of 150 mm are as follows: Constant head difference = 40 cm Time of collection of water = 83 sec Weight of water collected = 392 g Find the hydraulic conductivity a. 0.094 cm/sec b. 0.01 cm/sec C. c. 0.005 cm/sec d. 0.86 cm/sec