From the figure shown, H₁ = 0.60, H₂ = 0.90 m. and h = 0.45 m. The sand has a saturated unit weight of 18.65 KN/m³. Hydraulic conductivity of sand K= 0.12 cm/sec. If the cross sectional area of tank = 0.46 m², determine effective stress at point C in KPa. h=0.45m H₁-0.60 m H₂ 0.90 m Direction of flow ₂0 -1865: valve open

From the figure shown, H₁ = 0.60, H₂ = 0.90 m. and h = 0.45 m. The sand has a saturated unit weight of 18.65 KN/m³. Hydraulic conductivity of sand K= 0.12 cm/sec. If the cross sectional area of tank = 0.46 m², determine effective stress at point C in KPa. h=0.45m H₁-0.60 m H₂ 0.90 m Direction of flow ₂0 -1865: valve open

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter9: In Situ Stresses

Section: Chapter Questions

Problem 9.12P

See similar textbooks

Similar questions

[Seepage] tank shown below. For the sand, the following properties are given: e = 0.40 , G.S = 2.67 . Calculate the effective stress at A. a. Consider the upward flow of water through a layer of sand in a 1.2m Overflow 0.7 m Sand z = 0.9m 2 m Inflow
be the hydraulic conductivity at 20°C? Ans. 1.0 x 10 cm/sec 4. For a normally consolidated clay, the following values are given. k(cm/sec) 0.45 x 10 e 0.78 1.1 0.88 x 10 Estimate k at a void ratio of 0.97 6.0089 107
be the hydraulic conductivity at 20 Docs A20 pe 4. For a normally consolidated clay, the following values are given. k (cm/sec) 0.45 x 106 0.78 1.1 0.88 x 106 Estimate k at a void ratio of 0.97
2. Estimate the hydraulic conductivity (in cm/sec) of a poorly graded sand with the following characteristics: d100 = 0.425mm, d50= 0.3mm, d30 = 0.25mm, d10= 0.2mm, and do = 0.1mm. Show your work and circle your answer.
There is an upward flow of 0.06 ml/s through a sand sample with a coefficient of permeability 3 × 10^–2 mm/s. The thickness of the sample is 150 mm and the cross-sectional area is 4500 mm2.Determine the effective stress in N/m2 at the bottom the sample, if the saturated unit weight of the sample, is 18.9 kN/m3. Provide Diagram a.709.5 b.177.38 c.88.69 d.354.75
From the figure shown, H₁ = 0.60, H₂ = 0.90 m. and h = 0.45 m. The sand has a saturated unit weight of 18.65 KN/m³. Hydraulic conductivity of sand K= 0.12 cm/sec. If the cross sectional area of tank = 0.46 m², determine the total stress at point C in KPa. h=0.45m T H₁-0.60 m H₂-0.90 m Direction of flow H₂O Sand 1265 valve open
From the figure shown, the void ratio of the sand is 0.55 with a specific gravity of 2.68. The cross-sectional area of the tank is 0.5 sq.m and hydraulic conductivity of sand = 0.1 cm/s. a. What is the rate of upward seepage in cu.m/hour? b.Determine the critical hydraulic gradient for zero effective stress. c. Determine the value of h (head loss) to cause boiling. NEED ASAP. THANK YOU.
2. The depth of water in a well is 3 m. Below the |IAVA bottom of the well lies a layer of sand 5 meters thick overlying of the clay deposit. The specific clay a gravity respectively 2.64 and 2.70. Their water contents are respectively 25 and 20 percent. Compute the total stress, effective stress and the pore water pressures at pointS solids of sand and are 3m A and B of the figure shown. Sand 5 m A• Ans: 88 kN/m², 29.1 kN/m², 58.9 kN/m² $2 m 12 m Clay
11. Consider the downward flow of water through a layer of sand in the tank shown. (see picture below) Void ratio of the soil = 0.52 Specific Gravity = 2.70 Compute the value of h1. (Answer: 0.436) Compute the effective stress at A. (Answer: 17.44 kPa) Compute the effective stress at B. (Answer: 31.98 kPa) Compute the seepage force per unit volume. (Answer: 3.57 kN/m3)
3. For the system shown, L = 1.20m, h = 2.30m, and y = 1.90m. What is the effective stress 5. From the figure shown. at point A where z = 0.70m? h =1.5m 1.5m Standpipe G=2:68 é 0.5 Saud 2.5m Porous stone valve орen Soil A In flow Yan = 19.5 kN/m Cross - sectional area of tank = 0.6 m? Porous stone Hydraulic conductivity of sand = 0.1 cm/s a. What is the rate of upward seepage of water? b. What would be the critical hydraulic gradient?
2.11 A sand has the following: D10 = 0.2 mm, Dø = 0.4 mm, and void ratio e = 0.6. a. Determine the hydraulic conductivity using Eq. (2.38). b. Determine the hydraulic conductivity using Eq. (2.40).
Q4 A 0.7m long soil specimen is subject to a steady-state flow, as shown in Figure Q4. The saturated unit weight of the soil is 20 kN/m³. Determine the following: Datum Y 0.8 m Figure Q4 Water B d) Total stress (kPa) at point A, B and C. e) Porewater pressure (kPa) at point A, B and C. 0.3 m 0.3 m 0.4 m