6. A shaft of different diameters is planted to the wall at A and is subjected to torque loadings, as shown. Determine the maximum shear stress in the shaft. A fillet weld having a radius of 5 mm is used to connect the shafts at B. (note: the stress concentration diagram is given) 1000 N·m. 50 mm B 400N.m 30 mm 250 N·m 2.0 1.9 1.8 1.7 1.6 K 1.5 1.4 1.3 1.2 1.1 1.0 0.00 0.05 0.10 ▬▬▬▬▬▬▬▬▬▬▬ T D 0.15 LE 0.20 D/d 0.25 = 2.5 2.0 1.67 1.25 1.11 0.30

6. A shaft of different diameters is planted to the wall at A and is subjected to torque loadings, as shown. Determine the maximum shear stress in the shaft. A fillet weld having a radius of 5 mm is used to connect the shafts at B. (note: the stress concentration diagram is given) 1000 N·m. 50 mm B 400N.m 30 mm 250 N·m 2.0 1.9 1.8 1.7 1.6 K 1.5 1.4 1.3 1.2 1.1 1.0 0.00 0.05 0.10 ▬▬▬▬▬▬▬▬▬▬▬ T D 0.15 LE 0.20 D/d 0.25 = 2.5 2.0 1.67 1.25 1.11 0.30

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.94RP: The properties of the unequal angle section are Ix=80.9in.4,Iy=38.8in.4, and Iu=21.3in.4. Determine...

See similar textbooks

Similar questions

Following plate is connected to the wall using 7 bolts. Cross sectional area of each bolt is A. Force F is applied to the plate. The magnitude of shear stress experienced by bolt B is, 100.00 25.00 25.00 25.00 O 1. Less than F/(7A) O 2. F/(7A) O3. More than F/(7A) 80.00 20.00 20.00 20.00 (40 00)
Q.2. A bar with a rectangular cross-section is weld as shown. Determine the size weld, if the pemissible shear stress in the weld 80 MPa. The rectangle area of a fillet weld is equal to [ 2t (b+/)]. 31KN Please send the solution within half an hour and thank you
8. An acetylene tank consists of a cylindrical body flat at its base and a hemisphere at the other end. The thickness of the metal used in this tank is 2 mm. The tank has a diameter of 250 mm and 1200 mm long. What is the internal allowable stress of the material is 180 MPa? a. 3.5 kPa b. 6.8 kPa c. 4.2 kPa d. 5.5 kPa
Q.2. A bar with a rectangular cross-section is weld as shown. Determine the size weld, if the pemissible shear stress in the weld 80 MPa. The rectangle area of a fillet weld is equal to [ 2t (b+/)]. 31KN
A Ansle erson E leg the radius of the cylinder. and Fig. 10.19 Problems 10.3 and 10.4 The Anstwer: r = 0.26 m pove.
A cylindrical pressure vessel has an outside diameter of 1.5 meters, and a length of 5 meters. The vessel is made of steel with butt-welded seams and is 10 mm thick. The seams form an angle of 25 degrees with a plane perpendicular to the long axis, as shown. The allowable normal stress perpendicular to the weld is 150 MPa. The allowable shearing stress parallel to the weld is 80 MPa. What is the allowable gage pressure? Use (and draw) Mohr's circle. 25
A circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a torque of 8 kNm is applied to the shaft, what is the maximum stress in the weld?.
8) A plate 75 mm wide and 10 mm thick is joined with another steel plate by means of single transverse and double parallel fillet welds as shown in Fig.3. The joint is subjected to a maximum tensile force of 55 kN. The permissible tensile and shear stresses in the weld material are 70 and 50 N/mm2 respectively. The length of each parallel fillet weld is: 55 kN 55 kN Fig.3 O 25.29 mm 40.58 mm O 64.77 mm O97.58 mm 75 mm
A shouldered machine shaft is subjected to bending, as shown. The shaft is made from AISI 1015 CD steel with SuT= 390 MPa. For this shaft, D = 200 mm, d = 190 mm, and r = 28.5 mm. Determine the fatigue stress concentration factor using the Neuber Equation. D M O a. 1.3607 O b. 1.3308 O c. 1.5186 O d. 1.3698
150 18 F = 25 KN 25 200 25 25 100 € -25 25 50 Calculate the maximum combined stress in the throat of the 9 mm weld. Note that the weld is on the vertical sides only. All dimensions in millimeters.
The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 500 mm and a wall thickness of 6 mm. Determine the largest allowable gage pressure if the allowable shear stress parallel to the weld is 25 MPa. 50 O 2.63 MPa О 3.13 МРа О 3.36 МРа O 2.88 MPa O 2.44 MPa
Cal culate the stress between the two rods at the weld if the weld has a radius of 0.5 inch and the of the small area rod is 1" x 1.5" and T= 50 Kips %3D Calculate the stress at the cross averaye 0.5 diameter hole in the. section of the wider 1.5" x 2.5" rod, then calculate the stress concentration Mer around the 0.5" Diameter hole due to the 50 Kips Tensile force.