8) A plate 75 mm wide and 10 mm thick isjoined with another steel plate by meansof single transverse and double parallel filletwelds as shown in Fig.3. The joint is subjectedto a maximum tensile force of 55 kN. Thepermissible tensile and shear stresses in theweld material are 70 and 50 N/mm2respectively. The length of each parallel filletweld is:55 kN55 kNFig.3O 25.29 mm40.58 mmO 64.77 mmO97.58 mm75 mm

given:shear stress in weld =50N/mm2tensile stress=70N/mm2force=55kNB=75mmt=10mm

Answered: A plate 75 mm wide and 10 m oined with…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Asap
A 40mm thick steel bar that is fabricated by welding two parts together is shown below. Being concerned for the strength of the weld, you need to find the state of stress (normal stress and shear stress) in the plane of the weld for an applied load of 400kN. Draw your result on a stress element. 57° 400 kN 400 kN 100 mm
A rectangular plate (0 =25°) is formed by welding two triangular plates shown in figure. The plate is subjected to a compressive stress of 2.5 MPa in the x-direction and a tensile stress of 15 MPa in the y-direction. Determine the normal stress acting perpendicular to the line of the weld and the shear stress acting parallel to the weld. Lütfen birini seçin: a. 9.3175 MPa/6.09 MPa b. None c. 0.417 MPa/4.38 MPa d. 0.6256 MPa/6.70 MPa e. 11.874 MPa/6.70 MPa
Q2. A plate 120 mm wide and 8 mm thick is to be welded to another plate where the applied static load to the plates is 120 kN. The permissible ultimate and yield stresses are 640 MPa and 390 MPa respectively, find the length of weld when (a) a double transverse welds (b) a double parallel fillet welds are used, use factor of safety (2).
A cylindrical pressure vessel has an outside diameter of 1.5 meters, and a length of 5 meters. The vessel is made of steel with butt-welded seams and is 10 mm thick. The seams form an angle of 25 degrees with a plane perpendicular to the long axis, as shown. The allowable normal stress perpendicular to the weld is 150 MPa. The allowable shearing stress parallel to the weld is 80 MPa. What is the allowable gage pressure? Use (and draw) Mohr's circle. 25
Q1. A plate b mm wide and t mm thick is joined with another plate by a single transverse and a double parallel fillet weld as shown in Fig. if the permissible tensile and shear stresses in the weld material are otw MPa and tw MPa respectively and the permissible tensile stress in the plate material are otp MPa, Find the length Li of single transverse fillet weld, if the joint is subjected to both static and fatigue loading. All dimensions in mm.
3. An axial pull of 35000 N is acting on a bar consisting of three lengths as shown below. If the Young's Modulus is 2.1 x 105 N/mm2. Determine (i) Stresses in each section, and; (ii) Total extension of the bar. Section 3 Section 2 Section 1 35000 N 35000 N 2 cm DIA 3 cm DIA 5 cm DIA k-20 cm- 25 cm -22 cm-
A rectangular plate (0 =23°) is formed by welding two triangular plates shown in figure. The plate is subjected to a compressive stress of 2.3 MPa in the x-direction and a tensile stress of 13 MPa in the y-direction. Determine the normal and the shear stresses acting parallel to the weld. Weld Lütfen birini seçin: a. 10.664 MPa/5.50 MPa b. 0.3131 MPa/4.93 MPa c. None d. 0.0358 MPa/5.50 MPa e. 9.3175 MPa/6.09 MPa
A rectangular plate (0 =20°) is formed by welding two triangular plates shown in figure. The plate is subjected to a compressive stress of 2.0 MPa in the x-direction and a tensile stress of 10 MPa in the y-direction. Determine the normal and the shear stresses acting parallel to the weld. y Weld Lütfen birini seçin: a. -0.417 MPa/4.38 MPa O b. 9.3175 MPa/5.50 MPa O c.-0.596 MPa/3.85 MPa d. None e. 8.5962 MPa/3.85 MPa
A rectangular plate (0 =25°) is formed by welding two triangular plates shown in figure. The plate is subjected to a compressive stress of 2.5 MPa in the x-direction and a tensile stress of 15 MPa in the y-direction. Determine the normal stress acting perpendicular to the line of the weld and the shear stress acting parallel to the weld. y Weld Lütfen birini seçin: a. 0.417 MPa/4.38 MPa b. None O c. 0.6256 MPa/6.70 MPa O d. 11.874 MPa/6.70 MPa e. 9.3175 MPa/6.09 MPa O O O
A steel bar, with a rectangular cross section, has a butt-welded joint, as shown below, and will be used to carry an axial tensile load of 750 kN. If the normal and shear stresses on the plane of the weld must be limited to 80 MPa and 50 MPa, respectively, determine the minimum thickness t required for the bar. 750 kN 125 mm 60% O 750 kN
A 40 cm diameter steel tube is constructed with 0.5 cm thick welded plates, as shown in the illustration. If the tube is subjected to an axial tension load of 50 tons and a torque of 10 ton-cm, determine the normal and shear stresses acting in the plane of the weld, as shown in the figure. Express your answer in units of kgf / cm2. Consider that 1 ton = 1000 kgf.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A plate 75 mm wide and 10 m oined with another steel plat of single transverse and doub welds as shown in Fig.3. The o a maximum tensile force a