20mm Square plate is subjected normal stresses as illustrated. Modulus of Elasticity, E = 1081 MPa and Poisson's ratio is 0.35. If the initial thickness of the plate is 5mm. Determine the final thickness. Provide the answer in mm a with two decimal points of accuracy. σ = 80 MPa 20 mm Answer: D 20 mm σ = 160 MPa

20mm Square plate is subjected normal stresses as illustrated. Modulus of Elasticity, E = 1081 MPa and Poisson's ratio is 0.35. If the initial thickness of the plate is 5mm. Determine the final thickness. Provide the answer in mm a with two decimal points of accuracy. σ = 80 MPa 20 mm Answer: D 20 mm σ = 160 MPa

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.5P: The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen...

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
An aluminum plate is subjected to uniform stress along its boundaries, as shown in the figure. Determine the change of length of diagonal BD. 120mm 120 MPa 160mm , 100мра C 240 MPa E=80GPa ✓=0.3 G=30GPa Answer = -0.5888mm
PROBLEM 01: Hollow bar length is 1.40m long and tube length is three-fourth as long as the bar. Torque T=1100N.m acts at the free end of the bar. Both the bar and tube are made of an aluminum alloy with shear modulus of w ww elasticity G=27GN/m². Given that dl=35mm, d2=45mm, d3=60mm, d4=70mm. Determine the following: a. Maximum shear stress in both the bar and tube b. Angle of twist at the end A of the bar. (In degrees) Tube Fixed plate End plate Tube d3 d1 d2 d4 Bar Cross-section of the bar and tube
y 400 mm 4 mm B 200 mm A 6 mm The rectangular plate is subjected to the deformation shown by the dashed line. Determine the average shear stress in the plate if the shear modulus of the material is 2 MPa. Express your answer in kPa and round it to the nearest integer if necessary.
A compound bar consists of (4) aluminum alloy bars of (2mm) diameter and (2) steel bars of (3mm) diameter. Determine the followings: 1- The stresses in each material when a compressive force of 70 kN is applied on the compound bar and the temperature is changed from 20 °C to 40 °C. 2- The compound modulus of elasticity (Ec). Knowing that : E=200GN/m² E=70 GN/m² and a=11×10% per °C and a=22×10 per °C for Steel for Aluminum Alloy
7. A cylindrical steel bar is subjected to repeated compression-tension stress cycling along its axis. The mean stress is zero (0). If the maximum tensile load applied to the bar is 15,000 N, calculate the minimum allowable bar diameter (in mm) to ensure that fatigue failure will not occur. Assume a Safety Factor of 3. Show all work (4). 500 450 400 S 350 300 250 103 104 105 106 107 108 S (MPa)
The plastic distorts as shown by the dashed lines. (Figure 1) The dimensions are L= 460 mm H =310 mm di =2 mm, d2 =5 mm, dz = 15 mm, d4 =8 mm, d; =2 mm, and de = 5 mm. Part A Determine the shear strain Yry at corner C. Express your answer to three significant figures and include appropriate units. (yc)zy = Value Units igure Submit Request Answer dz Part B B Determine the shear strain yzy at corner D. Express your answer to three significant figures and include appropriate units. H HA ? D Value Units
Determine the following for the bar. A) B) C) D) σ, ksi 100 ksi 80 ksi T, ksi 40 ksi What is the Modulus of Elasticity for the material of the bar. What tensile force will cause the bar to yield? What will be the length of the bar after a 540 kip force is applied? What will be the cross sectional dimensions after a 300 kip force is applied? 0.0025 0.0035 0.0095 0.0100 0.0130 0.0145 Y, radians ɛ, in/in 20 in 3 in Cross Section 2 in
1 - An aluminum plate is subjected to uniform stress along its boundaries, as shown in the figure. Determine the change of length of diagonal BD. 120mm 120 MPa 160mm C B V 100MPa -200 MPa E-80GPa ✓=0.3 G=30MPa
Determine the a.Stress at 167 kN loadin MPa b.Strain at 167 kN loadin mm/mm(expressed in scientific notation) c.Modulus of elasticityMPa d.Modulus of resiliencein N-mm/mm3 e.Modulus of toughnessin N-mm/mm3
Question 8 The rigid, horizontal slab is attached to two identical copper rods. There is a gap A = 0.18 mm between the middle bar, which is made of aluminum, and the slab. Neglecting the mass of the slab, calculate the stress in each rod when the temperature in the assembly is increased by 85 °C. Use the following data: A (mm?) a (C) E (GPa) Each copper rod 500 16.8 x 10-6 120 Aluminum rod 400 23.1 x 10- 70 Copper unusunjv Copper 750 mm-
CLO 1: A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between them which is 699.93 mm long. If the weight of the beam is 375 KN, determine the stress in the aluminum bar (in MPa). Bronze Bronze Alum Alum Bronze A in mm2 850 1500 E in Gpa 70 83 103.56 O 79.45 451.30 33.47