11-1 A fixed-end beam AB of length L supports a uniform load of intensity q (see figure). Using the fourth order of derivative of deflection curve, solve for the reactions. 11-1 A fixed-end beam AB of length L supports a uniform load ofintensity q (see figure). Using the fourth order of derivative ofdeflection curve, solve for the reactions.9communMARABRB·XMB

Here we will use fourth order derivative of deflection curve to get the support reactions.

Answered: 11-1 A fixed-end beam AB of length L…

11-1 A fixed-end beam AB of length L supports a uniform load of intensity q (see figure). Using the fourth order of derivative of deflection curve, solve for the reactions.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.5.22P: -22 A simple beam AB supports a uniform load of intensity q acting over the middle region of the...

See similar textbooks

Related questions

Q: 2. For the gas system power illustrated in Figure 2 (with the air-standard analysis assumptions),…

A: The compression ration is

Q: Vo a static head and Assuming Constant flow rate take for How long would it take a quantity of water…

A: The static head of the water in the tank, (H)=5 ftThe diameter of the tank, (D)=4 ftThe…

Q: a) Compute the reactions at the supports b) Draw the complete shearing force and bending moment…

Q: A 6 cm diameter metallic sphere initially at a uniform temperature of 400 °C is placed in a…

A: The diameter of sphere is .The initial temperature of sphere is .The temperature of the environment…

Q: The hand clamp is constructed using a square-threaded screw having a mean diameter of 36 mm, a lead…

A: The force applied is .The coefficient of friction at the screw is .The mean diameter is .The lead is…

Q: Need only a handwritten solution only (not a typed one).

Q: 2. For the structure shown below. Beam ABC is a rigid beam of 10000 lbs in weight. Assume that rods…

A: Given;

Q: You pull on a string with a horizontal force of magnitude Fyb = 59 N that is attached to a block of…

Q: determine the rotation rate for the smaller , homologus pump . Using ONLY AFFINITY LAWS

A: To calculate the rotation rate of the smaller pumpgiven flow rategiven head of the pumpspeed of the…

Q: Determine the force in the member BC of the truss, and state if the member is in tension or…

A: Diven data,P = 420 lbFind outa) The force in the member BC of the trussb) The force in the member AC…

Q: The rigid bar ABCD is consist of two cylindrical portions AC and CD shown in Figure Q1.1.…

A: Consider the bar ABCD is discritised into three elements and represent the forces acting as…

Q: Rollers Model for a paper feeder in copy machine: 12cm 77 Simplified: Xp Friction, Vp 12cm 77 Xp xf…

A: The objective of the question is to determine the transfer function for the displacement of the…

Q: 104 kg/s of air flows through a jet engine. pressure is -3.3 kPa gage and the exit pre 2.70 m² and…

Q: 600 N Lm (b)

Q: 1. A coupling GY8 is fixed on a shaft by a type C flat key, as shown in the figure. And the…

A: Torque, T = 900 N-m.Stress, p = 100 MPaThe diameter of the shaft from the figure, d = 70 mm

Q: The steel beam in Figure A has the cross section shown in Figure B. The beam length is L = 6.0 m,…

A: The dimension are The length of beam is The maximum bending stress is

Q: Calculate the horizontal force P on the light 14° wedge necessary to initiate movement of the 30-kg…

A: Given -To Find-

Q: The level of liquid in a reboiler on a distillation column is controlled by using feedback control…

A: It is asked to draw the cascade arrangement, considering vapour pressure and actual flow rate as…

Q: A 100 kW pump is moving water at 1 m^3/min. If the inlet pressure is 200 kPa (gauge), what is the…

A: The power input to the pump, The volume flow rate of the water, The inlet pressure of the water,…

Q: The onset of free convection. Plastic shrink wrap can be used to insulate windows by trapping air…

Q: Two moles of ethane in a piston-cylinder assembly undergo a reversible adiabatic compression from…

A: Initial volume= 0.1 m3Final volume= 0.002 m3Initial pressure= 0.5 bar

Q: Problem 4: μk Ө @0 m VO The homogeneous disk of mass m and radius r is projected along the incline…

Q: The 2-kg collar is released from rest at A and slides down the inclined fixed rod in the vertical…

Q: Determine the y_bar coordinate of the composite shape. Treat the bent corners as square and ignore…

Q: 1. For the simply supported beam with a T-shape cross-section as shown below, a- Draw the shear and…

A: (a)Maximum Bending Moment =

Q: Consider a bar that is fixed at the left end and subjected to two forces as shown in the Fig. 3.…

Q: you solved it with a total distance of 8, not 10 like the question said. please resolve with a…

Q: The Gates Manufacturing Co. produces pulley wheels such as the one shown in (Eigure 1). Take a = 4…

A: The given wheel can be broken down into 5 parts - 2 circular disks with a hole in the centre, 2…

Q: A swivel bridge is bought into the desired position by means of a double–acting cylinder. The piston…

A: Pneumatic circuit of the system:

Q: The 1.69-kg uniform slender bar has a 0.70-kg particle attached to its end. The spring constant is k…

A: Introduction:We will determine the maximum angular deflection and the magnitude of the angular…

Q: pr... below. 5) Sketch the appropriate sectional view on the front view of the part

A: Given:To find:Sectional view on the front view.

Q: 20. = 3,500 mm, w = 0.5 m A = 2 cm²

Q: Find the toughness for a metal that experience valid for elastic deformation, that the modulu…

A: Given Modulus of Elasticity, E = 103 GPa K = 1520 MPa…

Q: USE AUXILIARY VIEWS TO DETERMINE THE TRUE SHAPE OF PLANE ABC. CALCULATE THE AREA OF PLANE ABC. Cp B₁…

A: An image is given;

Q: 15-1. A hammer head H having a weight of 0.3 lb is moving downwards at 40 ft/s when it strikes the…

Q: a) Calculate the reaction forces in terms of F and theta. b) Calculate the internal shear force and…

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Q1:A circular bar of 500 mm length is supported freely at its two ends. It is acted upon by a…

A: Given-Data:-l=500mmTo determine:The diameter of bar

Q: Required Information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: The weight of each pipe is The length of pipe is The diameter of each pipe is .

Q: 11. A steel shaft of 75 mm diameter is pressed into a steel hub of 100 mm outside diameter and 200…

Q: Please provide a visual, step-by-step lesson on how to create this solid model in solidworks, thank…

A: Assume the units are in mm.Open Part workbench in SolidWorks software and set the units to…

Q: What are the key challenges and trends in microchip design and fabrication as we move towards…

A: To explain:the key challenges and trends in microchip design and fabrication.

Q: 1) The figure below shows a system in which mass m2 is added to mass m1 (the spring is not…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Air at 600 kPa and 500 K enters an adiabatic nozzle at a velocity of 35 m/s and leaves at 350 kPa…

A: Given data

Q: H.W/ By using ASD and LRFD methods, find a light section W12xw of A992 steel material of member BC…

Q: голь 40° Find P. do, 25°

Q: Consider the centrifugal clutch above that comprises of four ‘shoes’ symmetrically attached to the…

A: We will divide the issue into three sections to answer it: question 1a will ask you to calculate the…

Q: Refer to Table 3.2 in the lecture and take the data for air, water (steam), and four other gases…

A: The values of thermal conductivity for the temperature range from 200 K to 600 K are plotted for…

Q: Determine the minimum tension in the rope at points A and B that is necessary to maintain…

A: The static coefficient of friction is .

Q: at the bottom of a container, which forms an angle A with the horizontal, is a cube of edge a, as…

Q: How does microchip design differ from microchip fabrication, and what tools and software are…

A: There are two separate stages in the process of making integrated circuits, or microchips: microchip…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

11-1 A fixed-end beam AB of length L supports a uniform load of intensity q (see figure). Using the fourth order of derivative of deflection curve, solve for the reactions.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2: Equilibrium conditions application

VIEW

Step 3: Boundary conditions application

VIEW

Step 4: Support reactions calculation

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A simple beam ABC has a moment of inertia 1,5 from A to B and A from B to C (see figure). A concentrated load P acts at point B. Obtain the equations of the deflection curves for both parts of the beam. From the equations, determine the angles of rotation 0Aand Bcat the supports and the deflection 6Bat point B.
A beam rests on supports at A and B and is loaded by a distributed load with intensity q as shown. A small gap exists between the unloaded beam and the support at C. Assume that span length L = 40 in. and flexural rigidity of the beam EI = 04 x 109lb-in2. Plot a graph of the bending moment at B as a function of the load intensity q. Hint: See Example 9-9 for guidance on computing the deflection at C.
A fixed-end beam AB carries point load P acting at point C. The beam has a rectangular cross section (b = 75 mm, h = 150 mm). Calculate the reactions of the beam and the displacement at point C. Assume that E = 190 GPa.
A two-span beam with spans of lengths L and L/3 is subjected to a temperature differential with temperature T1on its upper surface and T2on its lower surface (see figure). Determine all reactions for this beam. Use the method of superposition in the solution. Assume the spring support is unaffected by temperature. What are the reactions when k ?
Derive the equation of the deflection curve for beam AB with sliding support at A and roller at B* carrying a triangularly distributed load of maximum intensity q0(see figure). Also, determine the maximum deflection ôniill of the beam. Lsc the fourth-order differential equation of the deflection curve (the load equation).
A beam A BCD rests on simple supports at B and C (see figure). The beam has a slight initial curvature so that end A is 18 mm above the elevation of the supports and end D is 12 mm above. What moments Mtand M^, acting at points A and Dtrespectively, will move points A and D downward to the level of the supports? (The flexural rigidity EI of the beam is 2.5 X 106 N m2 and L = 2.5m).
A fixed-end beam AB of a length L supports a uniform load of intensity q (see figure). Beginning with the second-order differential equation of the deflection curve (the bending-moment equation), obtain the reactions, shear forces, bending moments, slopes, and deflections of the beam. Construct the shear-force and bending-moment diagrams, Labeling all critical ordinales.
A simple beam ACB supports a uniform load of intensity q on the left-hand half of the span (see figure). Determine the angle of rotation ÔBat support B>(Obtain the solution by using the modified form of Castigliano's theorem.)
-10 Derive the equations of the deflection curve for beam AB with sliding support at A and roller support at B, supporting a distributed load of maximum intensity q0acting on the right-hand half of the beam (see figure). Also, determine deflection A, angle of rotation B , and deflection cat the midpoint. Use the fourth-order differential equation of the deflection curve (the load equation).
-4 A simple beam ABCD has moment of inertia I near the supports and moment of iertia 2I in the middle region, as shown in the figure. A uniform load of intensity q acts over the entire length of the beam. Determine the quations of the deflection curve for the left-hand half of the beam. Also, find the angle of rotation A at the left-hand support and the deflection max at the midpoint.
A simple beam AB is subjected to couples M0and 2A0 acting as shown in the figure. Determine the angles of rotation 04and BBat the ends of the beam and the deflection S at point D where the load M0is applied.
-9 Derive the equations of the deflection curve for beam ABC with sliding support at A and roller support at B, supporting a uniform load of intensity q acting on the overhang portion of the beam (see figure). Also, determine deflection cand angle of rotation c. Use the fourth-order differential equation of the deflection curve (the load equation).