1.3. The annual load of a substation is given in the following table. During each month, the power is assumed constant at an average value. Using MATLAB and the barcycle function, obtain a plot of the annual load curve. Write the necessary statements to find the average load and the annual load factor. Annual System Load Interval, month | Load, MW January February March 8 4 April Мay June 2 6. 12 July August September October 16 14 10 4 November 6 December 8.

1.3. The annual load of a substation is given in the following table. During each month, the power is assumed constant at an average value. Using MATLAB and the barcycle function, obtain a plot of the annual load curve. Write the necessary statements to find the average load and the annual load factor. Annual System Load Interval, month | Load, MW January February March 8 4 April Мay June 2 6. 12 July August September October 16 14 10 4 November 6 December 8.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Similar questions

The p.u. impedance value of an alternator corresponding to base values of 13.2 kV and 30 MVA is 0.2 p.u. Then the p.u. impedance value of an alternator for the new base values of 13.8 kV and 50 MVA is......
Power factor correction is usually done by adding _________ to the load circuit.Select the correct response:a. switchb. capacitorc. inductive loads
The per unit impedance of a generator on a 60 MVA, 20 kV base is j0.09 p.u. The per unit impedance to a 100 MVA, 20 kV base will be (a.) j0.054 p.u. (c.) j 1.5 p.u. (b.) j0.54 p.u. (d.) j0.15 p.u.
The peak load on a 50 MW power station is 39 MW. It supplies power through for transformers whose connected loads are 17, 12,9 and 10 MW. The maximum demands on these transformers are 15, 10, 8 and 9 MW respectively. The annual load factor is 50% and the plant is operating for 65% of the period in a year. 102. The average load on the station is (A) 50000 kW (C) 39000 kW (B) 19500 kW (D) 48000 kW. 103. The energy supplied per year is (A) 438 x 106 kWh (C) 170.82 x 106 kWh (B) 341.64 x 106 kWh (D) 420.48 x 106 kWh.
The reactance of a generator is given as 0.25 per-unit based on the generator’s of 18 kV, 500 MVA. Find its per-unit reactance on a base of 20 kV, 100 MVA. a. 0.0505 b. 0.0605 c. 0.0405 d. 0.0606
A generating station is to supply four regions of load whose peak loads are10 MW, 5 MW, 8 MW and 7 MW. The diversity factor at the station is 1-5 and the average annual load factor is 60%. Then the installed capacity is (25 to26)MW. O (24 to25)MW. O (23 to24)MW. O
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator
In the system shown in Figure 1, the transformers are connected star-star with both star points grounded and the generators are connected in star with thier star points grounded. The system base is 15 MVA. The transformers all have reactances of 0.04 p.u. on this 15 MVA base. The reactances of all other elements are given in Table 1 (in 2) and the voltage levels are given in Table 2. p.u. G1 p.u. T1 jö Per-Unit Convert all values to p.u. on a 15 MVA base. Xa= p.u. Xc₂= XL = V BABE G1 2 X 9 T3 Figure 1: A section of the distribution system T1 L Table 1: Sequence reactances (2) 3 G1 L G2 0.3 0.59 0.01 4 L 9/10 10 Fault Voltage What is the voltage at bus 3 (in Volts) after the fault has occurred? Vp= V T2 5 T2 34 10/4 Table 2: Voltage bases (kV) G2 4 T3 10/9 | G2 Fault Current A three-phase fault with a fault reactance of 0.01 p.u. occurs at bus 3. Calculate the fault current flowing at the fault point in KA. Ip=-j KA So
Connect three single-phase transformers in Y-Y, with subtractive polarity, so that the line-to-line voltages on the primary are 30 degrees delayed to their respective line-to-line voltages on the secondary. It should show each step that is needed to make this connection (example: the phasor diagram) and should show the final connection of the three transformers including the polarity markings. Assume phase A on the primary is terminal "H1".
A 20 Ohm resistor is in series with a 30 Ohm Inductive reactance. If they are connected to a 40 Volt a.c. source, what is the phase angle between the voltage across the Inductive reactance, and the supply voltage (in degrees)? **Only give the magnitude. If you believe the current is lagging OR leading, give a positive value for the angle " I
In the system shown in Figure 1, the transformers are connected star-star with both star points grounded and the generator is connected in star with its star points grounded. The per unit impedances of each element on a 40 MVA base are given in Table 1 and the voltage levels are given in Table 2. Z [p.u.] 0 2 tööt Generator 0.01 +j0.08 p.u. L Figure 1: A section of the distribution system Transformer T1 Line V BASE [KV] 0.04 + j 0.03 + j 0.15000000000000002 0.06000000000000000 Generator Table 1: Sequence impedances (p.u. on 40 MVA base) 3 T2 181. Line 3 10 Table 2: Voltage bases (kV) Load 1 Transformer T2 Load Current A load current of 11.316 kA is flowing with a lagging power factor of 90 %. Convert this to a current vector in per-unit. IL = 0.04 + j 0.06000000000000000
Table Q2a Time (hours) 0-6 6-12 12-14 14-18 18-24 Load (MW) 45 90 135 150 75 Referring to the Table Q2a; i) Draw the load curve and the load duration curve [Use the graph paper provided] ii) Indicate the base load and the peak load on the graph. Determine the values for both loads. iii) Choose the suitable generating units to supply the load and list their operating schedules. Later, compute the total installed capacity. iv) Calculate the load factor and the plant capacity factor. Discuss the impact on the operating schedule if the plant capacity factor increases to 0.9.