1. The cantilever beam in Figure 1 is fixed A, and is loaded with a distributed load from B to C and a concentrated moment at D. (a) Determine all of the support reactions on the beam (at A). Show free-body diagrams (with all essential components), and clearly annotate all calculations. [ans.: A, 10 kN; Ax = 0; M₁ = 20 kNm] (b) Use the METHOD OF SECTIONS to determine expressions for the shear force and bending moment along the entire length of the beam. [Ans.: A to B: Q = 10 kN, M = 10x - 20 kNm; B to C: Q = -10x + 15 kN, M = -5x² + 15 x - 21.25 kNm; C to D: Q = 0, M = -10 kNm] (c) Plot the shear force and bending moment diagrams. X 0.5 m B 10 kN/m 1 m C 0.5 m 10 kNm D

1. The cantilever beam in Figure 1 is fixed A, and is loaded with a distributed load from B to C and a concentrated moment at D. (a) Determine all of the support reactions on the beam (at A). Show free-body diagrams (with all essential components), and clearly annotate all calculations. [ans.: A, 10 kN; Ax = 0; M₁ = 20 kNm] (b) Use the METHOD OF SECTIONS to determine expressions for the shear force and bending moment along the entire length of the beam. [Ans.: A to B: Q = 10 kN, M = 10x - 20 kNm; B to C: Q = -10x + 15 kN, M = -5x² + 15 x - 21.25 kNm; C to D: Q = 0, M = -10 kNm] (c) Plot the shear force and bending moment diagrams. X 0.5 m B 10 kN/m 1 m C 0.5 m 10 kNm D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Beam ABC is loaded as shown. Support C settles 10 mm after the load is applied. taking E = 200GPa and I = 300x10^6 mm4. Removing the support at B, what would be the vertical displacement at B of the primary structure in kNm3/EI, Find the Reaction at support B in kN and Determine the Linear flexibility coefficient taken at B, fBB, in kNm^3/EI.Single choice.
1. The beam is subjected to a load F = 400 N and is supported by the rope and the smooth surfaces at A and B. a. Draw the free-body diagram of the beam. b. What are the magnitudes of the reactions at A and B? 45% 1.2 m- -1.5 m- F 11 B 30⁰
What is the vertical reaction at E in kN.m? kN Solve for the support reaction of the beam shown in the figure below. Use W = 10 . A B D Hinge E Hinge 0.4 m 0.4 m 0.4 m 0.4 m O 8 O 4 16 O 12 O -8 -4 O -16
The beam supports a uniform load of 3.0 k/ft and a concentrated load of 12 k as shown in the figure below. Assume D is a pin support and B is a roller. Determine the reactions at B and D. Write the equation for the bending moment in beam segment BC. Assume "x" is measured from point B. • Write the equation for the shear in beam segment CD. Assume “x;" is measured from point D. 112 k 3.0 k/ft A C 12 ft 12 ft
1. Given: A structure shown below Find: (1) Determine the magnitudes and locations of the two distributed loadings. In other words, determine the magnitude and location of the loading between A and C, and those of the loading between D and B. (2) For the member DEB, (a) take the moment at B and find the reaction at E and (b) then find By by either Fy= 0, or EMp = 0. (Recall that support conditions at B and E are rollers, so there are no reactions in x-direction.) (3) For the whole structure, 3 unknown forces and moment at A (Ax, Ay and Ma) are the only unknowns. Determine those 3 unknowns at A. 900 N/m 900 N/m B A C D 2E - 3 m 3 m - 4 m - 3 m3 m-
A frame formed by joining a bent beam ACD with a bar BC by a hinge is supported at A and B as shown in Figure. A vertical load P = 150 N is applied at point D. For each member, determine: (a) The components of support reactions at A and B. (b) The axial force, shear force, and bending moment acting on the cross section at point O. P = 150 N 0.8 m or 0.5 m -0.15 m 0.1 m
Determine the reactions at the supports A, B, and C. EI is constant. Suppose that P = 9.5 kip. (Figure 1) Figure 1 of 1 3 kip/ft -6ft B. 6 ft 12 ft
P (kN) d (mm) t (mm) www 85 80 25 The beam in Figure Q2(a) has a cross-section as shown in Figure Q2(b), where the values of P, d and t are given in Table Q2. (a) Determine reactions, RA and Rg. (b) Determine the shear force at section AB and bending moment at point B. (c) Determine the neutral axis and moment of inertia of the cross section of the beam (d) Det hine the maximum tensile and compressive bending stress the beam at point B. (Formula: omax =). Then, plot the bending stress distribution. (e) Determine the maximum shear stress of at section AB. (Formula: T =). P (kN) t (m d (mm) 1.6 m 0.8 m d (mm) t (mm) t(mm) (a) Figure Q2
1.3-4 Segments AB and BCD of beam ABCD are pin connected at x = 4 m. The beam is supported by a sliding support at A and roller supports at C and D (see figure). A triangularly distributed load with peak intensity of 80 N/m acts on BC. A concentrated moment is applied at joint D. (a) Find reactions at supports A, C, and D. (b) Find internal stress resultants N, V, and M at x = 5 m. (c) Repeat parts (a) and (b) for the case of the roller support at C replaced by a linear spring of stiff- ness k, 200 kN/m (see figure). 80 N/m 200 N-m at joint D A D 4 m B\ 4 m ; 3 m Pin connection Part (c) PROBLEM 1.3-4
2. FORCE METHOD An overhang beam ABC is loaded as shown. Determine the reactions at the supports due to loading and a support settlement of 1 mm at the roller B. Take E = 200 GPa and I = 500(106) mmª. 20KN 20 k /m C 3m Im
1.3-4 Segments AB and BCD of beam ABCD are pin connected at x = 4 m. The beam is supported by a sliding support at A and roller supports at C and D (see figure). A triangularly distributed load with peak intensity of 80 N/m acts on BC. A concentrated moment is applied at joint D. (a) Find reactions at supports A, C, and D. (b) Find internal stress resultants N, V, and M at X = 5 m. (c) Repeat parts (a) and (b) for the case of the roller support at C replaced by a linear spring of stiff- ness ky = 200 kN/m (see figure). 80 N/m 200 N-m at joint D A 4 m B 4 m 3 m Part (c) Pin connection
B. The bent beam ABC is attached pin at C and rests against a roller support at B. Neglecting the weight of the beam, find 4. Reaction at B 1.5 m A. 3 m B 2 m 150 kg y 2.5 m 3 m 2 m 150(9.81) N RE FBD