1.3-4 Segments AB and BCD of beam ABCD are pin connected at x = 4 m. The beam is supported by a sliding support at A and roller supports at C and D (see figure). A triangularly distributed load with peak intensity of 80 N/m acts on BC. A concentrated moment is applied at joint D. (a) Find reactions at supports A, C, and D. (b) Find internal stress resultants N, V, and M at x = 5 m. (c) Repeat parts (a) and (b) for the case of the roller support at C replaced by a linear spring of stiff- ss k, = 200 kN/m (see figure). %3D

1.3-4 Segments AB and BCD of beam ABCD are pin connected at x = 4 m. The beam is supported by a sliding support at A and roller supports at C and D (see figure). A triangularly distributed load with peak intensity of 80 N/m acts on BC. A concentrated moment is applied at joint D. (a) Find reactions at supports A, C, and D. (b) Find internal stress resultants N, V, and M at x = 5 m. (c) Repeat parts (a) and (b) for the case of the roller support at C replaced by a linear spring of stiff- ss k, = 200 kN/m (see figure). %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A pin-connected structure is supported and loaded as shown below. Member ABCD is rigid and is horizontal before the load P is applied. Bars (1) and (2) are both made from steel [E = 30,000 ksi] and both have a cross-sectional area of 1.25 in.2. A concentrated load of P = 25 kips acts on the structure at D. Determine: (a) the normal stresses in both bars (1) and (2). (b) the downward deflection of point D on the rigid bar 120 in. 80 in. (1) C D 66 in. 102 in. 44 in. P
Link AC has a uniform rectangular cross section 3 mm thick and 12 mm wide. Determine the normal stress in the central portion of the link. (Hint: Link AC has one reaction acts in the direction of the link; and support B is pin support). 960 N 75 mm 175 mm 30⁰° 91 G. 150 mm 960 N
A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal before the load Pis applied. Bars (1) and (2) are both made from steel [E= 30000 ksi] and both have a 2 cross-sectional area of 0.92 in.. If the normal stress in each steel bar must be limited to 17.6 ksi, determine the maximum load P that may be applied to the rigid bar. 67in. 57in. 123in 108in. 34in D
A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal before the load P is applied. Bars (1) and (2) are both made from steel [E = 30,000 ksi] and both have a cross-sectional area of 1.25 in.2. If the normal stress in bar (1) must be limited to 19 ksi, determine the maximum load P that may be applied to the rigid bar.
The solid 60 mm diameter bent rod is fixed at O and is made of AISI 1035 HR steel. For the loading shown, determine the factor of safety against yielding at the location of ELEMENT H using; a) the Maximum Shear Stress theory and, b) the Henky-Von Mise, Distortion Energy theory. NOTE: All dimensions in mm. Fy = 6 kN 100 450 B Fx = 10 kN H 0 H 150 700 K y
The rigid bar EFG is supported by the truss system shown. Knowing that the member CG is a solid circular rod of 0.75-in. diameter and P = 5000 lb, determine the normal stress in CG. 3 ft B S D E The normal stress in CG is ft P -4 ft ksi.
The wall hanger has a thickness of 0.25 in. and is used to support the vertical reactions of the beam that is loaded as shown. If the load is transferred uniformly to each strap of the hanger, determine the state of stress at points C and D on the strap at A. Assume the vertical reaction F at this end acts inthe center and on the edge of the bracket as shown.
e (C) d (mm) P(kN) Q(N) Gallow (MPa) s(%) 20 18 80 12 40 1 (a) The structure shown in Figure Q3 is subjected to two point loads as shown. Determine (i) the axial force in rod BC and the reactions at pin A in terms of P. The value of angle, 0 is given in Table 3. the maximum load, P that can be applied if the average shear stress in each (ii) pin is not allowed to exceed 60 MPa. All pins are subjected to double shear and each has a diameter, d as given in Table Q3. (Hint: Consider only pin A and pin B.) RB 2 m-+-2 m P P Figure Q3 (b) A nylon thread is to be subjected to tension of Q (N). The modulus of elasticity, E of the thread is 3.2 GPa. Determine the required diameter of the thread, if (i) the maximum allowable normal stress is as given in Table 3; (ii) the length of the thread must not increase by more than s (%) as given in Table 3
Radius = 2 Find normel stress at pointA ? Find sheun stren at point A ? pnt A in
PROBLEM 2) The rigid bar ABC shown is hinged at A and supported by a steel rod at B. 8) Determine load P that can be applied at C if the stress in the steel rod is limited to 120MP..
2. Solve for the normal stresses at members CE, CH and BC in MPa if the area of each truss member is 1690mm2. 560 N 560 N 560 N -1.5 m -1.5 m 1.5 m- B 1 m 2 m E H. F
A vertical force of P = 1500 N is applied to the bell crank. 45% 300 mm B -450 mm- (a) Determine the normal stress developed in the 10mm diameter rod CD. (b) Determine the shear stress developed in the 6-mm diameter pin B that is subjected to double shear.