1-With most monostable multivibrators, what is the output when no input trigger has 2- The bit sequence 10011100 is serially entered (right-most bit first) into an 8-bit parallel out occurred? A. LOW, B. +5V, C. SET, D.HIGH shift register that is initially clear. What are the O outputs after four clock pulses? A. 10011100 В. 11000000 C. 00001100 D. 11110000 S-1f an 8-bit ring counter has an initial state 10111110, what is the state after the fourth clock pulse? A. 11101011 B. 00010111 С. 11110000 D. 00000000 4- A 555 timer in monostable application mode can be used for A. Pulse position modulation B. Frequency shift keying C. Speed control and measurement. D. Digital phase detector.

1-With most monostable multivibrators, what is the output when no input trigger has 2- The bit sequence 10011100 is serially entered (right-most bit first) into an 8-bit parallel out occurred? A. LOW, B. +5V, C. SET, D.HIGH shift register that is initially clear. What are the O outputs after four clock pulses? A. 10011100 В. 11000000 C. 00001100 D. 11110000 S-1f an 8-bit ring counter has an initial state 10111110, what is the state after the fourth clock pulse? A. 11101011 B. 00010111 С. 11110000 D. 00000000 4- A 555 timer in monostable application mode can be used for A. Pulse position modulation B. Frequency shift keying C. Speed control and measurement. D. Digital phase detector.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design the circuit that displays 35861429 on the seven segment display (just one). Use shift registers and button to slide numbers.
shift registers and explain how the PISO shift register functions find real life applications.
1. Consider the CRC generator shown below. Determine the output of the CRC circuit (i.e. Q4 Q3 Q2 Q1 Q0, expressed as a decimal number) for the input sequence "1010" (input one bit at a time, left to right). Assume the CRC circuit is initialized to state 11111. D Q0 Q2 Q4 Q1 Q3 Clock - Data In
Frequency Counted Input Conditioning Main Gate Counting Register Display Input Signal Main Gate Flip-Flop Time Base Oscillator Time Base Dividers The counter of the block-schemas above displays: Select one: 1. Phase 2. Period 3. Frequency
Design an encoding matrix with diodes and resistors to display a decimal number to on the seven-segment display. You have 10 switches (WO-W9) with one terminal connected to Vec. For decimal number 0, switch 0 (S0) is closed, for decimal number 1, switch 1 (S1) is closed etc. (Switches are on the vertical axis, S0 on top and the outputs are taken on the horizontal axis (Y0-Y6), with “a" on the left and "g" on the right. Note that (Y0-Y6) outputs are used as inputs to seven-segment display. Since these outputs cannot drive the seven segment display LEDS you may need additional bipolar transistors and resistors. The supply voltage is 5V and each LED needs a current of 20mA. Note that this is a design problem and the design is not unique. Do your best! f a a e
Please try this question It's is digital signal processing question
Q2/ A- Sum of series of 10 numbers stored at memory location 0100H:0500H and then store result in memory location [total] and also sum the number of carry if found and save it at memory location [carry] B- Draw The waveforms of 8086 minimum mode input bus cycle
1-Write microprocessor program using mnemonics to add two numbers 08 and 06. 2-Write the object code of the program. 3-Perform the program using STEP function. 4-Execute the program and write the results. Object code Mnemonics MOV AX A1 B0 MOV AL B3 MOV BL 04 ADD AL F4 HLT
Question-1 A) Write the instructions for the following scenario: Read two numbers from input ports (10,11). If the both inputs are equal jump to label (equal) in which put 15 in hexa into register B and halt the program, Otherwise load(-3) to the accumulator, and continually increment the accumulator to reach to 2. B) Type above program on GnuSim8085 and run it three times with the input values in the following table, and in each run fill line of the following table. Note: (don't forget to reset all before each run and update the input port) Port 1 Port 2 Register A Register B | Flag s Flag z 7.
Draw a state diagram for: Mealy state machine to detect the 1010 sequence. The output becomes one when you receive the sequence of 1100 and the output is zero otherwise. Overlap is allowed between the detected sequences.
Basic signal system question do it fast
A 9-bit asynchronous counter has a 128-kHz clock signal applied. (1) What is the MOD number of this counter? MOD number = (ii) What will be the frequency at the MSB output? fmsb = (iii) Assume that the counter starts at zero. What will be the count after 635 input pulses? After 635 input pulse, Count =