02/ Assuming that a 2-bit ADC channel accepts analog input ranging from 0 to 5 volts,determinea. The number of quantization levels L)b. The step size of the quantizer or resolution;Dc. The quantization level when the analog voltage is 2.3 volt; Re. Determine the quantization error when the analog input is 2.3 voltsOiConrider the analog signal x.ft) = est: Suppose that x. (t) is sampled at(T, D 0.005,eg

According to the information given:- We have to calculate the given requirement on the basis of…

02/ Assuming that a 2-bit ADC channel accepts analog input ranging from 0 to 5 volts, determine a. The number of quantization levelsL) b. The step size of the quantizer or resolution; c. The quantization level when the analog voltage is 2.3 volt; Ro e. Determine the quantization error when the analog input is 2.3 volts nột: Sunnore that r.(t) is sampled at (T,= 0.005,

02/ Assuming that a 2-bit ADC channel accepts analog input ranging from 0 to 5 volts, determine a. The number of quantization levelsL) b. The step size of the quantizer or resolution; c. The quantization level when the analog voltage is 2.3 volt; Ro e. Determine the quantization error when the analog input is 2.3 volts nột: Sunnore that r.(t) is sampled at (T,= 0.005,

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter8: Data And Network Communication Technology

Section: Chapter Questions

Problem 28VE

See similar textbooks

Similar questions

The information in an analog waveform, with maximum frequency f = 3 kHz, is to be transmitted over an M-ary PAM system, where the number of pulse levels is M = 16. The quantization distortion is specified not to exceed t 1% of the peak-to-peak analog signal. (a) What is the minimum number of bits / sample, or bits / PCM word that should be used in digitizing the analog waveform? (b) What is the minimum required sampling rate., and what is the resulting bit trans-mission rate? (c) What is the PAM pulse or symbol transmission rate? (d) If the transmission bandwidth (including filtering) cquals 12 kHz, determine the bandwidth efficiency for this system.
Question 4: A data signal has a frequency >1MHz, but there is unwanted signal at about 100Hz. i) Design a high-pass filter (the circuit is as shown in Figure 3) that attenuates the unwanted signal by 98%. ii) What is the effect of the measurement signal at its minimum of 1MHZ?
. Find the analog output voltage of a 5-bit digital to analog converter for any five inputs. Assume the value of K = 1. . What is the percentage resolution of a 8-bit digital to analog converter (DAC).
Question 1: A. Given an 8 bit ADC, find its resolution (step size) for producing a digital signal for an analog input ranging 260 - 516 V. Draw the first and last 3 steps of a table with 3 columns showing the analog ifiput-digital output numeric relationship. B. The frequency of an analog signal is 23 MHz. What is the minimum sampling frequency for representing it in digital form, according to the Nyquist theorem? Explain with the help of a diagram what happens if Nyquist theorem is not obeyed.
A Vin = 1.2V is fed into an 8-bit ADC with a step size of 8.5 mV, the digital output signal is equal to (You must only consider the integer part of the decimal number of Dout) 4
Write a VHDL file that uses a selected signal assignment statement to encode the following truth table. A 0 0 0 0 1 1 1 BC 0 0 1 1 0 1 0 1 0 0 1 11 XYZ 0 1 1 0 0 1 0 1 1 0 0 1 0 1 0 1 0 0 010 0
The difference in the delay of the signal may create a difference in Phase explain?
In a certain digital waveform, the period is four times the pulse width. The duty cycle is(a) 25% (b) 50% (c) 75% (d) 100%
A 12-bit analog-to-digital converter (ADC) advertises an accuracy of the least significant bit (LSB). If the input range of the ADC is 0 to 10 V, what is the accuracy of the ADC in analog volts?
Assume a digitization of a unipolar signal that can change between 0 to 9V volts into 4 bit digital equivalent. Calculate the resolution and the number of quantized levels. Show the graph of the ADC. Show your complete solution.
7. For the pulse shown in Figure 1–60, graphically determine the following:(a) rise time (b) fall time (c) pulse width (d) amplitude
Q1 for the input binary sequence (bk) = {1,-1, 1,-1} .find the transmitted phase sequence and sketch the transmitted waveform for PSK system.