... Hamstring 20cm Weight of lower leg + foot =4.5kg The weight of the lower leg and foot combined is 4.5kg and the horizontal distance of Cmass for the lower leg and foot together is 20cm from the center of the knee joint. The hamstring insertion on the tibia is 2cm from the knee joint. How much force (in Newtons) does the hamstring have to produce to lift the leg? Add your answer

... Hamstring 20cm Weight of lower leg + foot =4.5kg The weight of the lower leg and foot combined is 4.5kg and the horizontal distance of Cmass for the lower leg and foot together is 20cm from the center of the knee joint. The hamstring insertion on the tibia is 2cm from the knee joint. How much force (in Newtons) does the hamstring have to produce to lift the leg? Add your answer

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.78P: The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016,...

See similar textbooks

Similar questions

The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016, determine the force F required to advance the bar at a constant speed.
A man weighs 170 lb on the surface of the earth. Compute his weight in an airplane flying at an elevation of 28 000 ft.
The level of a common steelyard without hook connections weights 7kg and acts at 5cm to the left of the fulcrum. The hook which carries the load,weights 4kg and is also attached on the left-hand side of the fulcrum at a distance of 12cm.if graduation mark 72cm from the fulcrum reads 50kg. Find (a).the weight of rider (b). How far is the zero graduation from fulcrum (c).What is the movement of riderper kg of graduation?
asap
A car is hanging over a hole, supported by a rope tied to the ceiling and a person pulling the rope. How much force is exerted by the person in the configuration below, given the car weighs 3500 lbs? ** å 30° 则

In a hydraulic press, the small cylinder has the diameter of 8 cm while the larger piston has thediameter of 22 cm. If the force of 600 N is applied to the small piston, what is the force on thelarger piston, neglecting friction?
Find the axial force in BC (in units of kN). The mass of the box is 900 kg. (Make sure to include a negative sign if it is in compression.) 13 m 40° L 12 m 12 m 5 m 13 m
Two weights are hung over two frictionless pulleys that are connected by a wire rope to a 500 Ib horizontal block that are in between and below them. The wire rope attached to the upper left end of the block and to the left pulley is at 45 degrees with the horizontal and the wire rope that connects the upper right end of the block to the right pulley is at 30 degrees with the horizontal. If the weight on the left pulley is 50 lb, fs= 0.30 and fk = 0.20 on the surface of block what weight W on the right pulley will cause the 500 lb block to just start moving to the right? *
A great pianist is getting ready for his concert and plan to move his exclusive grand piano to his concert venue. The 700 kg piano needs to be loaded onto a truck bed which is about 1.5 m high.1.Initially, the movers decide to use an adjustable ramp to move the piano. The ramp can only be adjusted up to 10 m long and the inclination angle must not exceed 20° to ensure a safe loading process. Determine the range of a suitable length and angle of the ramp. 2.On a second thought, the movers are considering whether it is easier to lift the piano straight up onto the truck bed or push it up along the rough the ramp. With the aid of an appropriate free body diagram, justify the most efficient option for the movers to load the piano to the truck bed with constant speed. State clearly all the assumptions made, and the principles used in the calculations to support your answers.
HYDRAULICS & ELECTRO-HYDRAULICS The Diameters of a small piston and a large piston of a hydraulic jack are 5 cm ad 10 cm respectively. A force of 80 KN is applied on the small piston. Find the load lifted by the large piston when the pistons are at the same level.
The component of the force along the inclined plane due to mass of the body on a inclined plane is 500N. The net force acting on the body is 100N.The force of friction is Select one: 5 N 400 N 600 N 0.2 N
Two bodies is connected in point C, are supported by rigid underlay at an angle α. F is the force acting on right body. We are considering the weight of bodies G and the friction between the bodies and the underlay. Length of bodies l=2000mm.    G1= 160 N, G2= 180 N, α = 30° Find:  1.) Find the magnitude of the force so that it slips on the underlay 2.) Draw the dependence of the force F as a function of the coefficient of friction f (in the range 0-0.5)