You are to design a 24 volt, all dc stand-alone PV system to meet a 2.4 kWh/day demand for a smallisolated cabin. Size the PV array to meet the load in a month with average insolation of 5 kWh/m²-day.The maximum power point of the available PV module occurs at has VR = 18 V and IR= 5 A. Assumea 0.8 derate factor for dirt, wiring and mismatch (20% loss). You are to use a 200 Ah, 12 V batterieswith 100% coulomb efficiency.A) How many modules are needed (you may round up or down)? Sketch your PV array.B) How many 200-Ah, 12-V, deep cycle batteries would be required to cover three days of no sungiven the maximum depth of discharge is 75%? show how the batteries will wired up. Sketch yourbattery array.C) What will be the rating of a suitable charge controller to nearest multiple of 10 A.

You are to design a 24 volt, all dc stand-alone PV system to meet a 2.4 kWh/day demand for a small isolated cabin. Size the PV array to meet the load in a month with average insolation of 5 kWh/m²-day The maximum power point of the available PV module occurs at has VR= 18 V and Ir= 5 A. Assume a 0.8 derate factor for dirt, wiring and mismatch (20% loss). You are to use a 200 Ah, 12 V batteries with 100% coulomb efficiency. %3D A) How many modules are needed (you may round up or down)? Sketch your PV array. B) How many 200-Ah, 12-V, deep cycle batteries would be required to cover three days of no sun given the maximum depth of discharge is 75%? show how the batteries will wired up. Sketch your battery array. C) What will be the rating of a suitable charge controller to nearest multiple of 10 A.

You are to design a 24 volt, all dc stand-alone PV system to meet a 2.4 kWh/day demand for a small isolated cabin. Size the PV array to meet the load in a month with average insolation of 5 kWh/m²-day The maximum power point of the available PV module occurs at has VR= 18 V and Ir= 5 A. Assume a 0.8 derate factor for dirt, wiring and mismatch (20% loss). You are to use a 200 Ah, 12 V batteries with 100% coulomb efficiency. %3D A) How many modules are needed (you may round up or down)? Sketch your PV array. B) How many 200-Ah, 12-V, deep cycle batteries would be required to cover three days of no sun given the maximum depth of discharge is 75%? show how the batteries will wired up. Sketch your battery array. C) What will be the rating of a suitable charge controller to nearest multiple of 10 A.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.31P: Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in...

See similar textbooks

Similar questions

An RLC series circuit connected to a 110 – volt and 50 – cycle AC source, contains the following series resistances and reactances: R1 = 10 ohm, R2 = 15, R3 = 5 ohms, XL1 = 20 ohms, XL2 = 25 ohms, XC = 40 ohms. Find the following: a.) EQUIVALENT REACTANCE b.) TOTAL IMPEDANCE c.) VOLTAGE DROP ACROSS THE CAPACITOR d.) TOTAL INDUCTANCE IN MILLIHENRY e.) TOTAL CURRENT f.) REACTIVE POWER g.) REAL POWER DRAW THE PHASOR DIAGRAM IF POSSIBLE AND ROUND OFF TO FOUR DECIMAL PLACES
A series resistance – capacitance (R – C) circuit is connected to 230 – volt, 50 cycle AC source. The current through the resistor is 45.45 A and the power taken by the circuit is 5,000 watts. Compute the following: a.) VOLTAGE DROP ACROSS THE RESISTOR b.) POWER FACTOR ANGLE c.) CIRCUIT IMPEDANCE d.) OHMIC VALUE OF THE RESISTOR e.) CAPACITIVE REACTANCE f.) CAPACITANCE IN MICROFARAD g.) APPARARENT POWER PLS SOLVE ALL ROUND OFF TO FOUR DECIMAL PLACES solvE LETTER D, E F, AND G PLSS PLSS KINDLY SOLVE FAST
Consider Two same size Parallel connected PV modules,each with the specification as Po=100W, Voc= 24.5V and Isc=5A.then choose the correct Statement Refer to this connection. a. The output power and voltage from this panel is Po=50W,Voc= 24.5V b. The output power and voltagefrom this panel is Po=200W,Voc= 24.5V c. The output power and voltage from this panel is Po=200W,Voc= 49.0V d. The output power and voltage from this panel is Po=100W,Voc= 24.5V
What are the types of Converter Topologies in PV System?
b) What are the advantages and disadvantages of solar PV cell combined connection?
Q1. What is the principle of Buck-Boost type DC-DC converter? Derive the expression of voltage gain of it. A buck type converter is connected to a PV module, a 60 2 of load impedance and operated at a duty cycle of 45%. What would be the reflected impedance? If the PV module's voltage will be 26.8 Voltage. Find the current of it.
A series resistance – capacitance (R – C) circuit is connected to 230 – volt, 50 cycle AC source. The current through the resistor is 45.45 A and the power taken by the circuit is 5,000 watts. Compute the following: 1.) Power factor angle 2.) Circuit impedance 3.) Ohmic value of the resistor
8)This MCQ QUESTION FROM BASIC POWER ELECTRICAL ENGINEERING course.
Describe and discuss PV Grid-Connected Systems.
Q4. The source current in the circuit shown is in Figure 3a) What impedance should be connected across terminals a,b for maximum average powertransfer?b) What is the average power transferred to the impedance in (a)?c) Assume that the load is restricted to pure resistance. What size resistor connected across a,bwill result in the maximum average power transferred?d) What is the average power transferred to the resistor in (c)?v
How to generate 480V three phase 400Hz ac from 230V three phase 60Hz ac source? (Please specify the power components you pick, such as transformers, dc-dc converter, dc-ac converter and/or ac-dc converter, how these components are connected and the key parameters of these components, such as the turns ratio of transformer and the duty cycle functions for the converters.)
Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in Figure 2.27. (a) Obtain expressions for P12 and Q12. (b) Determine the maximum power transfer and the condition for it to