A manufacturing plant installed the system above (500 KW) and has a full load capacity of 700KW and runs one 8-hour shift per day at full load, assuming the PV system runs at maximum output for that 8-hour shift, what would be the % reduction in power drawn from the grid in that one shift? Briefly explain your answer.

A manufacturing plant installed the system above (500 KW) and has a full load capacity of 700KW and runs one 8-hour shift per day at full load, assuming the PV system runs at maximum output for that 8-hour shift, what would be the % reduction in power drawn from the grid in that one shift? Briefly explain your answer.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.31P: Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in...

See similar textbooks

Similar questions

With no load attached, the voltage at the terminalsof a particular power supply is 50.8 V. When a 10-Wload is attached, the voltage drops to 49 V.a. Determine vS and RS for this nonideal source.b. What voltage would be measured at the terminalsin the presence of a 15- load resistor?c. How much current could be drawn from this powersupply under short-circuit conditions?
Discuss the integration of renewable energy sources like wind and solar into the power grid. What challenges and solutions are associated with this integration?
Discuss the integration of renewable energy sources into the power grid, including the challenges and solutions.
Explain the concept of a smart grid and its advantages in modern power systems. What technologies and strategies are involved in making a grid "smart"?
Consider Two same size series connected PV modules,each with the specification as Po=100W, Voc= 24.5V and Isc=5A.then choose the correct Statement Refer to this PV Panel. a.The output power from this panel is 100W , the Voltage is 24.5V and the current is 10A b.The output power from this panel is 200W , the Voltage is 24.5V and the current is 10A c.The output power from this panel is 200W , the Voltage is 49V and the current is 5A d.The output power from this panel is 200W , the Voltage is 49V and the current is 10AClear my choice
Q4. The source current in the circuit shown is in Figure 3a) What impedance should be connected across terminals a,b for maximum average powertransfer?b) What is the average power transferred to the impedance in (a)?c) Assume that the load is restricted to pure resistance. What size resistor connected across a,bwill result in the maximum average power transferred?d) What is the average power transferred to the resistor in (c)?v
Identify the characteristics of AC and DC voltage. Runs at a higher temperature Answer 1Choose...DCAC More dangerous to transfer Answer 2Choose...DCAC Easy to produce Answer 3Choose...DCAC Easier to transform voltages Answer 4Choose...DCAC Voltage remains at a constant value Answer 5Choose...DCAC Cheaper to produce
Explore the challenges and solutions in integrating renewable energy sources like wind and solar into the power grid.
Why in high voltage system, we prefer direct or small resistance? How to define the classes of load? Why we should to do such classification??(find answer from website) what are the main load curves of the power system? What is the maximum load utilization hours? What are the applications of load curve and annual load curve in the design and operation of power system? (find answer from website)
The incremental fuel costs, in dollars per megawatthour, for two units in a plant are given by dF dP, dR dP, Select one: = 0.007P, +7 and During a 24-h period the load on each unit varies between 100 MW and 500 MW, whereas the plant output varies from 200 MW to 700 MW. (a) At what power level should unit 2 begin to take on all the additional load for the most economic operation of the plant? (b) What is the power output of the plant at this point? Neglect losses. a. a: 122.22MW. b: 222.22KW b. a: 222.22MW, b: 122.22KW ca: 122.22MW, b: 222.22MW d. a: 222.22MW, b: 122.22MW = 0.009P₂ +6
explain the major components of pv power systems.
How do renewable energy sources, such as wind and solar, impact the operation and planning of power systems?