Answered: The uniform 80 kg slender rod is at…

The uniform 80 kg slender rod is at rest in the position shown when P = 450 N is applied. Determine the value of angular velocity, w2 the rod if L1 = 5.5 m and L2 = 6.5 m. %3D

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.87RP: Can the uniform bar of weight W remain at rest in the position shown?

See similar textbooks

Related questions

Q: gear is supported by a fixed pin at O, determine the angular velocity of the gear and the velocity…

Q: F19-2. The 300-kg wheel has a radius of gyration about its mass center O of ko = 400 mm. If the…

Q: Determine the velocity of the 142-kg cylinder B after it has descended a distance of 6 m. Initially,…

Q: Q3: The 10 kg slender bar is attached to the small roller A, which glides freely along the groove.…

A: Find the angular acceleration of the bar and the acceleration of the roller immediately after it is…

Q: The rod assembly is supported by a ball-and-socket joint at C and a journal bearing at D, which…

A: Solution:

Q: The 20 kg roll of paper has a radius of gyration kA = 85 mm about an axis passing through point A.…

A: Given data: The mass of roll is m=20 kg The radius of gyration of the roll is kA=85 mm=0.085 m The…

Q: The dump truck carries 5 m³ of dirt with a density of 1600 kg /m³, and the elevating mechanism…

A: Data given - Volume of dump truck = 5 m3 Density = 1600 kg /m3 Mass m = density × volume =…

Q: Determine the initial angular acceleration of the 25-kg ladder and the initial reactions at A and B…

Q: Q3: The tire has a weight of 30 lb and a radius of gyration kg = 0.6 ft. If the coefficients of…

Q: Treat the 50 kg slender bar as it is moving in a “GENERAL PLANE MOTION." he 50 kg slender bar is…

A: Given:mass of the bar = 50 kgL= 3 m

Q: Q3) Pulley A weighs 7.5 kg and has a radius of gyration of ko= 0.25 m. If the system is released…

Q: *18-44. Determine the speed of the 50-kg cylinder after it has descended a distance of 2 m, starting…

A: Write the expression of the moment of inertia of gear A. Write the expression of the moment of…

Q: The body consists of a uniform slender bar and a uniform disk, each of mass m/2. It rests on a…

Q: The spool has a mass of 150 kg and a radius of gyration of Kc = 240 mm about its centre of mass G.…

Q: T The force of T = 30 N is applied to the bord of negligible mass. Determine the angular velocity of…

Q: F17-17. The 200-kg spool has a radius of gyration about its mass center of kg = 300 mm. If the…

Q: The uniform disk is initially at rest and has a mass of 24 kg. Its moment of inertia about its mass…

Q: 6/40 If the frictional moment at the pivot O is 2 N m, de- termine the angular acceleration of the…

A: Consider below FBD for the given question: Here, m1 = 12 kg m2 = 7 kg r1 = 200 mm = 0.2 m r2 = 300…

Q: velocity of 34 rad.s1. Disk E has a weight of 65 lb : is initially at rest when it is brought into…

A: There are two types of forces that are acting on a circular surface. One type of force is Radial…

Q: The disk has a weight of 10 lb and is pinned at its center O. If a vertical force of P = 2 lb is…

A: Draw the free-body diagram of the disc.

Q: 6/40 If the frictional moment at the pivot O is 2 N m, de- termine the angular acceleration of the…

A: Drum mass = 8 kg Radius of gyration = 225 mm Moment = 2 N.m

Q: 100 mm 175 mm The uniform disk has mass 25 kg sits at rest on fixed ground, at this insta nt, a…

A: Given, Force, F=80Nstatic friction,μs=0.20kinetic friction,μk=0.12mass of disk, m=25kgradius of the…

Q: The airplane is traveling in a straight line with a speed of 300 km/h, when the engines A and B…

A: Given data: TA = 40 kN TB = 20 kN Time, t = 5s Mass, m = 200 mg Radius of gyration, kG = 15 m

Q: The body is initially at rest and released from the horizontal position shown below. What is its…

Q: If the system starts from rest and no slipping occurs and cylinder A weighs 450 N and has a radius…

A: Given: Initially system is at rest and There is no slipping between cylinder and surface. Thus…

Q: 18-15. The pendulum consists of a 10-kg uniform disk and a 3-kg uniform slender rod. If it is…

Q: The slender 12-kg bar has a clockwise angular velocity of w= 2 radis when it is in the position…

A: m=12 kgW=12×9.81=117.72 Nω=2 rad/sec Now taking moment at…

Q: If a horizontal force of P = 100 N is applied to the 300-kg reel of cable, determine its initial…

A: Horizontal force P=100 N Weight of reel of cable M=30 kgRadius of gyration ko=.6 m

Q: The particle of mass m = 2.5 kg is attached to the light rigid rod of length L = 1.27 m, and the…

Q: The 5-kg cylinder is initially at rest when it is placed in contact with the wall B and the rotor at…

A: Given Mass of the cylinder = 5 kg Angular velocity = 6 rad/s Coefficient of the friction = 0.2 To…

Q: The 50 kg flywheel has a radius of gryation = 0.4 m about its shaft axis and is subject to the…

Q: winding drum that operates the elevator. If the elevator has a mass of 900 kg, the counterweight C…

A: Given data: Torque, M = 6kN.M Mass of the elevator, mE = 900 kg Counterweight C, mC = 200 kg Mass of…

Q: F18-2. The uniform 50-lb slender rod is subjected to a couple moment of M = 100 lb - ft. If the rod…

A: Given data: Weight of uniform beam, W = 50 lb. Couple moment acting on the beam, M = 100 lb·ft.…

Q: The uniform square steel plate has a mass of 8 kg and is resting on a smooth horizontal surface in…

A: Apply horizontal equilibrium motion equation.

Q: 40 If the frictional moment at the pivot O is 2 N m, de- termine the angular acceleration of the…

A: Given Data T=2 N.m K=225 mm m=8 kg

Q: The 136-kg spool has a radius of gyration about its mass center of ke = 300 mm If the couple moment…

Q: The uniform 45 kg slender rod is at rest in the position shown when P = 525 N is applied. What is…

A: Given Data Mass of slender rod is : m=45 kg Applied force is : P=525 N L1=3.75 L2=4.75 m

Q: The spool has a mass of 200 kg and a radius of gyration of kG = 0.2 m. If the coefficients of static…

Q: The solid homogeneous cylinder, with a mass of 5 kg and a radius of r= 0.12 m, is released from rest…

A: mass = 5 kg radius = 0.12 m Angle = 38o

Q: F17-16. The 20-kg sphere rolls down the inclined plane without slipping. Determine the angular…

A: FBD radius=0.15 m ∵ equilibrium eqn → ΣF=m ax →mg…

Q: The 12-kg slender rod is pinned to a small roller that slides freely in the slot. If the rod is…

A: Given, The mass of the slender rod, m = 12 kg The angle from which rod is released, θ = 0⁰ The…

Q: the speed of the loader in t = 10 s starting from rest. The wheels roll without slipping

Q: F17-15. The 20-kg wheel has a radius of gyration about its center O of ko = 300 mm. When the wheel…

A: Given data as per the question Mass of wheel =20 kg The radius of gyration =300 mm Coefficient of…

Q: If the cord is subjected to a horizontal force of P = 146 N, and the gear is supported by a fixed…

Q: 2) The shown spool has a mass of 450 kg and a radius of gyration k, =1.2m. It rests on the surface…

A: The free-body diagram of the spool is given as, In this diagram, Fr is the friction force, N is the…

Q: At the instant shown, the spring is un-deformed. Determine the change in potential energy if the 20…

Q: The Charpy impact test is performed using the pendulum which has a mass m, mass center at G and…

A: Given: Mass of the pendulum is m. Radius of gyration about point G is kg. The pendulum is shown…

Q: The spool has a mass of 20 kg and a radius of gyration of ko = 160 mm. If the 15-kg block A is…

A: To obtain the solution to the given question, we must do the energy balance of the body from its…

Q: The 0.25 kg slider A is pushed along the circular bar by the slotted bar. The circular bar lies in…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

The uniform 80 kg slender rod is at rest
in the position shown when P = 450 N is
applied. Determine the value of angular
velocity, w2 the rod if L1 = 5.5
m and L2 = 6.5 m.
A
L
L2
L1
B

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Given Data

VIEW

Step 2 Calculation

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Draw the FBD for the bar described in Prob. 5.1 if the bar is homogeneous of mass 50 kg. Count the unknowns.
Can the uniform bar of weight W remain at rest in the position shown?
The homogeneous 240-lb bar is supported by a rough horizontal surface at A, a smooth vertical surface at B, and the cable BC. Draw the FBD of the bar and count the unknowns.
The 186-kg wheel has a radius of gyration about its center O of ko = 300 mm, and radius r = 0.4 m. When the wheel is subjected to the constant couple moment M = 92 N.m, it starts rolling from rest. Determine the average friction force that the ground applies to the wheel if it has been rolling without slipping. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper Sl unit. Take g = 9.81 m/s². M Your Answer: units Answer
- The unifom bar OC of lmgth L md mass (m) pivots freely about a horizontal axis through O. If the spring of modulusk is unstretched when C is coincident with A, detennine the tension T roquired to hold the bar in the position shown. The diameter of the small pulley at D| is negligible. L/2 L/2
4. The 0.25 kg alider A is pushed along the circular bar by the slotted bar. The eireular bar lies in the horizontal plane. The angular ponition of the slotted bar is - 10t2 rad. Determine the Bagnitude and direation (measured from the horizontal) of the external force exerted on the elider at t- 0.2 .
Consider the system of two blocks. Thereis no friction between block A and the tabletop. The mass of block B is5.00 kg. The pulley rotates about a frictionless axle, and the light ropedoesn’t slip on the pulley surface. The pulley has radius 0.200 m andmoment of inertia 1.30 kg . m2. If the pulley is rotating with an angularspeed of 8.00 rad/s after the block has descended 1.20 m, what is themass of block A?
1372. The unbalanced wheel shown in Fig. P-1372 weighs 322 lb and has a maas radius of Kyrstion of 0.866 ft with respect to a horizontal Axin through its gravity center G. At the given instant, w- 3 rad per see and a- 6 rad per oc", both clockwise. If the heel does not alip, determine the value of P which ia directed parallel to the ineline. Ana. P- 251 lb 1373. If the unbalanced wheel described in Prob. 1372 starta from rest when at the posi- tion shown in Fig. P-1372 and does not alip, determine the initial angular neceleration cauned hy a pull P- 24O Ib.
A spring with squared and ground ends has 16 active coils diameter of 6 mm and pitch of 10 mm . If spring rate is 85 KN/m , determine the solid force?
The uniform 45 kg slender rod is at rest in the position shown when P = 525 N is applied. What is the total work done U1-2 when the rod goes to vertical position? Take L1 = 3.75 m and L2 = | 4.75 m. L2 L1 B
P23-2. The homogenous door shown has a mass of 60 kg and is held in the position shown by the rod AB. The rod is held in place by smooth horizontal pins at A and B. The hinges at C and D are smooth, and the hinge at C can support thrust along its axis. Draw the FBD necessary to determine all forces that act on the door. 950 mm 300 mm 60⁰ 300 mm 950 mm 300 mm y
The mass is 60kg. determine: a)the magnitude F. b)the components of reaction at thrust bearing at A and smooth journal bearing at B.