AC 0.6 m

Q: i need question 8 answer******* please i need solutions with full steps.

A: Part (a) Modulus of elasticity: It is defined as the ratio of longitudinal stress and strain. In a s...

Q: F2-25. Determine the angle 0 between the force and the line AO. F={-6i+9j+3k} kN 2 m 1m -2 m

A: The unit vector along the line of action of force can be determined as,

Q: 2-21. Determine the magnitude and direction 0 of FA so that the resultant force is directed along th...

A: Write the given data: Force can have any direction. But to simplify our calculation we resolve the ...

Q: Consider the flow of air through a wind turbine whose blades sweep an area of diameter D (in m). The...

A:

Q: To determine the maximum allowable axial force applied to a cylindrical column by four different sup...

A: Given :    

Q: Use the following conversions where necessary:1hp = 745.7W; ρwater = 1000 kg/m3; ρmercury = 13600 kg...

A:

Q: Determine by direct integration the moment of inertia of the shaded area with respect to the y axis.

A: Consider a differential element parallel to x-axis of width x and thickness dy as shown below.

Q: A barge is 15 ft wide and 40 ft long and fl oats with a draftof 4 ft. It is piled so high with grave...

A: Given data as per question Width of barge = 15 ft Length of barge= 40 ft Draft = 4ft let M is metace...

Q: The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. The outer diameter of this sleeve is...

A: Given data: *The diameter of the steel bolt is ds=10 mm. *The outer diameter of the sleeve is db=20 ...

Q: Steep safety ramps are built beside mountain highways to enable vehicles with defective brakes to st...

A: Given data as per question

Q: Show that the temperature profile of two fluid streams (hot and cold) that have the same heat capaci...

A:

Q: In an ice-making plant, water at 0C is frozen at atmospheric pressure by evaporating saturated R-134...

A: Given : The temperature of liquid refrigerant R -134 a= -16°C The rate of ice produced = 2500 kg/h T...

Q: Throwing a ball from 4 m height from the ground, when the ball left your hand, it had a speed of 3 m...

A: This problem is based on projectile motion. In the projectile motion, horizontal velocity will remai...

Q: A furnace that has a 40-cm * 40-cm glass window can be considered to be a blackbody at 1200 K. If th...

A: Given data Area of the glass window =  Temperature of the furnace = 1200 K Transmissivity     

Q: Can the normal strain on the free surface of a body be measured in aparticular direction using an el...

A: The magnitude of the strain measures using the device strain gauge. Strain gauge works on a differen...

Q: Discuss equations used to calculate unknown flow rates or diameters for each pipe section in piping ...

A: In order to proceed the question, some assumptions should be taken. The flow is steady and fully de...

Q: A solid circular rod that is 600 mm long and 20 mm in diameter is subjected to an axial force of P =...

A: Given data: Length of the rod (L) = 600 mm Diameter of the rod (D) = 20 mm Axial force (F) = 50 kN C...

Q: Do the principal stresses represent the maximum and minimum normal stress?

A: Principal planes are the planes on which the shear stress is zero or the planes on which the normal ...

Q: Give an example of concentrated force.

A: Whenever total magnitude of a force act on a single point then this type of loading on a beam is ter...

Q: Consider the flow of saturated steam at 270.1 kPa that flows through the shell side of a shell-and-t...

A: Given data saturated pressure Psat=270.1KPa = 2.7bar No of tubes n= 4 Diameter of teh tube d = 1.25 ...

Q: What are the general equations of plane stress transformation?

A:

Q: The state of plane stress at a point on the surface of the airplane fuselage isrepresented on the el...

A:

Q: The bent rod is supported at A, B, and C by smooth journal bearings. The rod is subjected to the for...

A:

Q: Part A - Elastic strain energy equation Determine which equation below should be selected to make th...

A: Write the given information.

Q: How is Dilatation, or volumetric strain caused ?

A: The volumetric strain is defined as the ratio of change in volume of the body to the original volume...

Q: A 1.8-m-diameter spherical tank of negligible thickness contains iced water at 0°C. Air at 25°C flow...

A: The data given is, The temperature of iced water = 0°C The temperature of air = 25°C Velocity of ai...

Q: A single-pass cross-flow heat exchanger withboth fluids unmixed has water entering at 16°C and exiti...

A: Given: The temperature of the water entering heat exchanger, Tw,1 = 16⁰C The temperature of the wate...

Q: A 3-ft3 rigid tank initially contains saturated water vapor at 300°F. The tank is connected by a val...

A: Given data: *The total volume of the tank is V=3 ft3. *The temperature of the saturated water vapour...

Q: The gravitational constant g is 9.807 m/s2 at sea level, but it decreases as you go up in elevation....

A: The expression for g is given as, The weight of the floating Astronaut is written as,  

Q: Weights measured in grams of randomly selected M&M plain candies: 0.957 0.912 0.925 0.886 0.920 0.95...

A:

Q: Mechanical Engineering Question

A:

Q: F1 = 10 kN Determine the force in each member and state whether it is in tension or compression

A:

Q: The clutch system shown in Fig is used to transmit torque through a 2-mm-thick oil film with ? = 0.3...

A: Write the given information.

Q: An intrepid treasure-salvage group has discovered a steelbox, containing gold doubloons and other va...

A: The specific weight of seawater is , The box volume is (2ft)(5ft)(1.5ft) , The buoyant force on th...

Q: 17-51. The wood column is fixed at its base and free at its top. Determine the load P that can be ap...

A: For buckling Where  is effective length For one end fixed and other free  is Moment of Inertia abo...

Q: The steel shaft is subjected to the two loads. If the journal bearings at A and B do not exert an ax...

A: Given data as per question Allowable bending stress = 180 MPa. Free body diagram of the system

Q: Why is the throttling valve not replaced by an isentropic turbine in the ideal vapor-compression ref...

A: The throttling valve is not replaced by an isentropic turbine. These are the reasons behind it, (1) ...

Q: If the cross section of the femur at section a–a can be approximated as a circular tube as shown, de...

A:  Considering the equilibrium of femur,

Q: If the 600-kN force acts through the centroid of the cross-section, determine the location y of the ...

A: Given figure and loading conditions

Q: A well-insulated heat exchanger is to heat water(cp = 4.18 kJ/kg8C) from 25 to 60C at a rate of 0.5...

A: Given data: *The initial temperature at the inlet of the heat exchanger is T1 =25 degree Celsius. *T...

Q: A beam supports a distributed load as shown. (a) Determine the equivalent concentrated load. (b) Det...

A: Understand that intensity of the total load is the area of the loading diagram (trapezium) and the r...

Q: Gate AB in Fig.  is a quarter circle 10 ft wide into thepaper and hinged at B . Find the force F jus...

A: Given data: Width of the gate = 10 ft Weight of the gate =3000 lbf Weight density of water, γ = 64.2...

Q: The assembly has the diameters and material indicated. If it fits securely between its fixed support...

A: The coefficients of thermal expansion for Aluminium, Bronze, and Steel are: The modulus of elastici...

Q: Write the equation which will represent conservation of angular momentum.

A: Conservation of angular momentum: The law of angular momentum conservation states that there will be...

Q: What is uniaxial tension?

A: Consider the schematic diagram to have a better understanding of the problem.

Q: please i need the solution with full steps

A:

Q: 12–47. A two-stage rocket is fired vertically from rest at s = 0 with the acceleration as shown. Aft...

A: Given data   

Q: In a thermal system, water enters a 25-mm-diameter and 23-m-long circular tube with a mass flow rate...

A: Given data Diameter of the pipe Dp = 25mm =0.025m Length of the pipe L= 23m mass flow rate of the pi...

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.