The assembly is used to support a 10 kN point load at the tip as shown. The steel rod has a diameter of 12 mm, and the steel pins each have a diameter of 8 mm. T wooden bar ABC has a height of 100 mm and a thickness of 40 mm. Taking yiel stress in tension and shear for steel of oy=480 MPa and ty=270 MPa, respective and tensile strength of 17 MPa for the wood, determine (a) The factor of safety of the steel rod BC (b) The factor of safety of pins at B and C (c) The factor of safety of the wooden bar ABC (d) The bearing stress at pin A. Steel rol. 12 an 1.5. Wael inber 100 me

The assembly is used to support a 10 kN point load at the tip as shown. The steel rod has a diameter of 12 mm, and the steel pins each have a diameter of 8 mm. T wooden bar ABC has a height of 100 mm and a thickness of 40 mm. Taking yiel stress in tension and shear for steel of oy=480 MPa and ty=270 MPa, respective and tensile strength of 17 MPa for the wood, determine (a) The factor of safety of the steel rod BC (b) The factor of safety of pins at B and C (c) The factor of safety of the wooden bar ABC (d) The bearing stress at pin A. Steel rol. 12 an 1.5. Wael inber 100 me

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the stress and total load on each stringers if the web is negligible. Estainless steel = 28000 ksi, Esteel = 29000 ksi, EMagnesium = 6500 ksi, EAlum. Ally = 10500 ksi 6" Steel 10 .10 a Stainless Steel My = 5000"# 10" Mx = 10000"# Magnesium .1 Alloy Area of Each 10 Alum. Alloy Stringer = 1 sq. in. 4"
The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (ay) MPa, and for the bronze (ay)or 520 MPa, determine the magnitude of the largest elastic load P 640 that can be applied to the assembly. E 200 GPa, Ebr= 100 GPa. 10 mm 20 mm Figure 2: Steel Bolt
8 ksi, oy The normal stresses at a point in a steel member are ox 10 ksi. Using E -4 ksi, 29 x 103 ksi and v = 0.3, determine the normal strains at 2.31 %3D and oz this point. %3D ר- The rectongulor block, of material of€ length Land cross sectional ore 1 fits
Derve the maximum steel ratio and the recommended steel ratio. show solution and explanation.
determine: (a) the elastic section modulus and the yield moment. (b) the plastic section modulus and the plastic moment Mp. Bending is about the x-axis, and the steel is A572 Grade 50. Fy = 345 MPa Subject: Civil Engineering Steel Design
The two wooden boards are connected by a 0.9 in. diameter bolt. Washers are installed under the head of the bolt and under the nut. The washer dimensions are D = 3.0 in. and d = 1.0 in. The nut is tightened to cause a tensile stress of 14000 psi in the bolt. Determine the bearing stress between the washer and the wood. Answer: Ob = Bolt 1575 D - Washer - Washer Nut psi
Situation No. 2 A bronze bar is fastened between a steel bar and an aluminum bar as shown below. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Bronze Steel A = 480 mm? Aluminum A = 650 mm A = 320 mm 3P 4P 2P 1.0 m 2.0 m 1.5 m
The two wooden boards are connected by a 0.7 in. diameter bolt. Washers are installed under the head of the bolt and under the nut. The washer dimensions are D = 2.4 in. and d = 0.8 in. The nut is tightened to cause a tensile stress of 12000 psi in the bolt. Determine the bearing stress between the washer and the wood. Answer: Ob = i Bolt D Washer psi - Washer Nut
The following steel member is connected to the gusset plate via two longitudinal welds. The width of the member is 58 mm and the length of the weld is 87 mm. The yield stress is 300 MPa and the ultimate stress is 675 MPa. The gross area of the member is 700 mm^2 . a. What is the tensile design yield strength in KN? b. What is the tensile design rupture strength in KN? c. If a tensile load of 85 KN is requiredfor the member, what is the minimum factor of safety for the steel member?
What is the manufacturing tensional yield strength (lbf) of grade S135 drill pipe? a. This is a trick question because drill pipe size is not provided b. The answer can’t be calculated because the length of the pipe is not given c. The yield strength is 135000 psi and is a property of the steel d. The yield strength is 135000 psi and depends on the cross-sectional area
The angle L 8 x 8 x ½ in tension shown in the figure below must resist aservice dead load of 35 kips, live load of 50 kips, and a roof live load of 2kips. The steel used is A50 (Fy = 50 ksi, Fu = 65 ksi) and its welding length is 4”.Determine if the member has sufficient fracture and yield strength.
In assembly drawings, the washer is used to . the tightening force on the part. Select one: O a. distribute O b. increase O . decrease