The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. The outer diameter of this 640 sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (ay) MPa, and for the bronze (ay)or 520 MPa, determine the magnitude of the largest elastic load P that can be applied to the assembly. E 200 GPa, E= 100 GPa. 10 mm 20 mm

The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. The outer diameter of this 640 sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (ay) MPa, and for the bronze (ay)or 520 MPa, determine the magnitude of the largest elastic load P that can be applied to the assembly. E 200 GPa, E= 100 GPa. 10 mm 20 mm

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter14: Material Selection

Section: Chapter Questions

Problem 3ETSQ

See similar textbooks

Similar questions

Situation No. 2 A bronze bar is fastened between a steel bar and an aluminum bar as shown below. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Bronze Steel A = 480 mm? Aluminum A = 650 mm A = 320 mm 3P 4P 2P 1.0 m 2.0 m 1.5 m
Please
A Solid Steel bar of diameter 60mm and length 3.50mm is placed inside an aluminum cylinder of inside diameter 70mm and outside diameter 110mm, a compressive load of looo la is applied on the assembly, find the stresses in the bar and the cylinder? take Est = 200GPa and EA1 = 70 Gra. P=1000KN Cover Plate 0.25mm d- 350mm di do t Alum, cylinder Steel bar
Problem 2: A bronze bar is fastened between a steel bar and an aluminum bar as shown. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Steel Bronze 480 mm² 650 mm² 3P 1.0 m 4P 2.0 m Aluminum 320 mm² 1.5 m 2P
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. %3D Steel E200 GPa A-600mm L1 m 2.0 m 0.6 m 1.5 m Pa20 KN Aluminum E-70 GPa A=900mm L-1.5 m What is the ratio of the deformation of steel to deformation of aluminum?
The assembly consists of two A992 steel bolts AB and EF and an 6061-T6 aluminum rod CD. When the temperature is 30°C, the gap between the rod and rigid member AE is 0.1 mm. Assume BF is also rigid. (Figure 1) Figure 400 mm A B 25 mm 50 mm D 0.1 mm 300 mm E 1 of 1 25 mm Part A Determine the normal stress developed in the bolts if the temperature rises to 180°C. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. of = Submit Part B σ₁ = Submit O HA Value Request Answer Provide Feedback ■μÅ Value Determine the normal stress developed in the rod if the temperature rises to 180°C. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Units Request Answer wwwww Units ? wwwww Review ? Next >
1.12 A fillet-welded joint of 6 mm size is shown in the figure. The welded surfaces meet at 60-90 degree and permissible stress in the fillet weld is 108 MPa. The safe load that can be transmitted by the joint is 100 mm F F 810 50mm
7) A specimen of steel 20 mm diameter with a gauge length of 200 mm is tested to destruction. It has an extension of 0.25 mm under a load of 80 kN and the load at elastic limit is 102 kN. The maximum load is 130 kN. The total extension at fracture is 56 mm and diameter at neck is 15 mm. Find (i) The stress at elastic limit. (ii) Young's modulus. (iii) Percentage elongation. (iv) Percentage reduction in area. (v) Ultimate tensile stress.
The length of the assembly shown below decreases by 0.5 mm when an axial force is applied by means of rigid end plates. Determine (a) the magnitude of the applied force, (b) the corresponding stress in the brass core.
A 8 mm radius Steel is subjected to tensile test. Determine its yield and and ultimate load it can carry in kN when the steel grade is 60 and 40. Determine also its elongation using the stresses if the modulus of elasticity of steel 218 GPa. Determine also the weight if the length is 8 m and 18 m.Hint: There are two 8 mm radius Steel.
The following steel member is connected to the gusset plate via two longitudinal welds. The width of the member is 58 mm and the length of the weld is 87 mm. The yield stress is 300 MPa and the ultimate stress is 675 MPa. The gross area of the member is 700 mm^2 . a. What is the tensile design yield strength in KN? b. What is the tensile design rupture strength in KN? c. If a tensile load of 85 KN is requiredfor the member, what is the minimum factor of safety for the steel member?
A No. 10 steel rebar is tested in tension. By monitoring the load reading of the testing machine, it was found that the specimen yielded at a load of 41,600 lb and fractured at 48,300 lb.a. Determine the tensile stresses at yield and at fracture.b. Estimate how much increase in length would occur at 70% of the yield stress in a 2-in. gauge length.