Q1. B. In the single-phase half-wave rectifier shown below, assume that the load current iola is constant (load inductance L is very large). (i) Sketch the load voltage waveform vo for a = 90° and find its average value V dc. 10 2 find the average and rms values of the (ii) For R = diode current ia for a = 45°. V₁ (240 V rms) + Vo L (large)

Q1. B. In the single-phase half-wave rectifier shown below, assume that the load current iola is constant (load inductance L is very large). (i) Sketch the load voltage waveform vo for a = 90° and find its average value V dc. 10 2 find the average and rms values of the (ii) For R = diode current ia for a = 45°. V₁ (240 V rms) + Vo L (large)

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is CEMF?
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consistingseries connected a resistor and an inductance from a 70.7V (RMS), 50Hz sinusoidal AC source.The firing delay of the thyristor is 90° and the load values are R=10Ω, L=0.1 H. Define the loadcurrent expression and draw the load current by calculating for first two periods. And calculate theaverage values of the load voltage and current.
Design a single-phase full wave bridge rectifier with input voltage of 100v and inductive load of 10ohm and 40mH a. Show the waveform relation between the I/P and O/P b. Calculate the average O/P voltage c. Calculate the rms current
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V rmsh soHz} VL-DC =20V 0.01 F 0.02 F 0.0167 F None of the above
1. Build the following circuit. Use the function generator to obtain the specified AC input voltage. D4 D1 + RL 1.2K + Vs D3 Y D2 9V sin(2n 50 t) Verify the amplitude and frequency of the output waveform on the load resistor, RĻ. Peak voltage: Waveform period: Frequency 1.c) Calculate the average power dissipated on all four rectifier diodes (assume that each diode is ON for exactly one half cycle of vs for simplicity).
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
P) For single - phase half-controlled bridge rectifier shown in the figure: 1. Derive a formula for mean load Voltage. 2. Draw the waveforms of Ve,is,iz, i3, iy and io assuming highly inductive Load and =45. T. T3 Dy
Note: Answer All question 1: A) For a single-phase half-wave uncontrolled rectifier with (RL) load, find the rms value of the output voltage (V) and form factor (FF%) with supply voltage: v,(t) = 10 sin(wt). Draw the circuit diagram and sketch the voltages and current waveforms. The conduction angle B = 220°. %3D
92) For three - phase half-wave Controlleed rectifier Shown in he figure: 1. Derive a fomu la for mean load Voltage. 2. praw the wave form of vo, i,,i, iy and voltage across thyristor 1 (r.) assuming highly inductive load and d = 120
A three-phase rectifier is supplied by a 173.2-V rms line-to-line 60-Hz source. The RL load is a 100 resistor in series with a 15-mH inductor. Determine THD taking Is1 = 1.35