1. Build the following circuit. Use the function generator to obtain the specified AC input voltage. D4 D1 + RL 1.2K + Vs D3 Y D2 9V sin(2n 50 t) Verify the amplitude and frequency of the output waveform on the load resistor, RĻ. Peak voltage: Waveform period: Frequency 1.c) Calculate the average power dissipated on all four rectifier diodes (assume that each diode is ON for exactly one half cycle of vs for simplicity).

1. Build the following circuit. Use the function generator to obtain the specified AC input voltage. D4 D1 + RL 1.2K + Vs D3 Y D2 9V sin(2n 50 t) Verify the amplitude and frequency of the output waveform on the load resistor, RĻ. Peak voltage: Waveform period: Frequency 1.c) Calculate the average power dissipated on all four rectifier diodes (assume that each diode is ON for exactly one half cycle of vs for simplicity).

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
Problem # 4 In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VpC e. PIV (Peak Inverse Voltage) 10:1 Dy 1ISV ms Ouiput RL 2.2 k2 D, 50 pF All diodes are IN4001. alleee
For the circuit shown below, compute the maximum current through each resistor when terminal A is a) positive and, b) negative. Assume the diodes are ideal. (Will we convert to the RMS value to it's actual value?)
Determine the a.c. ripple voltage across the load of full wave rectifier which delivers 40 W to a load resistance of 150 ohm, and ripple factor is given as 1% A) 77.4 V B) 38.7 V C) 0.387 V D) 0.774 V
B. Draw the circuit diagram of a clipper that will produce an output waveform below. From the outp waveform Voltage A is 8.7 and Voltage B is -9.7.Input peak-to-peak voltage is given as 20 volts. Assi Silicon diodes are used. 7 B 1. For the positive half cycle, the needed battery voltage is 2. For the negative half cycle, the needed battery voltage is
Consider the following circuit diagram. Using practical diode model solve the following items. i. What is the type of rectification in this circuit? ii. Calculate the total peak secondary voltage (Note that “RMS" value is given in the circuit) iii. Sketch the plot of time vs voltage over Load (RL) iv. Find the average voltage over Load. v. Find the maximum current passing over diodes. vi. Find the peak inverse voltage (PIV) over the diodes. vii. Find the minimum fuse current rating for the primary coil. 5:1 D DA 120 V rms D3 D2 RL=10kQ RL out ell lelll
(ii) Briefly explain the principle of operation of the rectifier circuit. Ensure to explain about the pair of diodes that conduct for the positive cycle and the pair that conducts for the negative cycle of the input signal. (iii) Suppose the input signal vs(t) is a sine wave with a peak voltage of 8 V and frequency of 50 Hz. Sketch the output signal across the load resistor R₂ with the expected peak voltage. Also state the ripple frequency beside the waveform. (iv) Explain why there is a short period between pulses when the output voltage is zero.
Can someone please provide a step by step solution? Thank you! The full wave rectifier in the circuit below is to deliver 0.25A and 15V (peak) to a load. The ripple is to be no larger than 0.4 V peak-to-peak. The input signal is 120 V (rms) at 60 Hz. Assume V(lambda) = 0.7 V . Determine the required turns ratio, the filter capacitance, and the diode PIV rating.
Q1 Figure Q1(a) is a full wave bridge circuit with a capacitor filter and the output waveform produced by the circuit is shown in Figure Q1(b). Assume all the diodes in the circuit have a forward voltage of 0.7 V. (a) (b) Sketch the waveform in A, B, C and D as shown in Figure Q1(a). Design the circuit by finding the value for the capacitor, C and the line voltage Vpri(rms) to the circuit to produce the output as shown in Figure Q1(b).
For the rectifier in the figure below, state the conduction sequence of the diodes for periods t1 to tó. D1 D2 D3 22) tl: D. & D.. 23) t2: D. & D.. 24) t3: D. & D.. 25) t4: D. & D.. D4 D5 D6 26) t5: D. &D. 27) t6: D.AN A & D....... Vm cot t6
Determine the voltage across the diode, the output voltage, and the current in the resistor in the figure below. Plot these waveforms with proper ac cycle phase alignment. 1SR154-400 is a silicon rectifier 1 ampere diode. Indicate the peak values as per calculation.
Consider the half-wave rectifier shown below. It needs to deliver 0.1 A and an average of 15 V to a load. The source is 60 Hz and the diode has a 0.7 V drop. The allowable ripple is no more than 0.4 V (2.5%). Find: Peak AC voltage Vm of the source a) b) The minimum value of the smoothing capacitor(s) c) Comment on the type of capacitor and its/their values you would use for this amount of capacitance vs(t) K Load UL