PROBLEM SOLVING 2 The plates are connected by 12-mm bolts in Figure 5. The maximum axial stress of each plate is 20 MPa and the maximum shear stress of each bolt is 14 MPa. Determine the maximum Force F that can be applied to the plates. F F 340 mm W 340 mm Figure 5: Bolted Plates F 150 mm F 50 mm

PROBLEM SOLVING 2 The plates are connected by 12-mm bolts in Figure 5. The maximum axial stress of each plate is 20 MPa and the maximum shear stress of each bolt is 14 MPa. Determine the maximum Force F that can be applied to the plates. F F 340 mm W 340 mm Figure 5: Bolted Plates F 150 mm F 50 mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.5.1P

See similar textbooks

Related questions

Q: Question 42 A circular beam of 300 mm diameter is made up of a material having permissible stress 80…

A: Given - Diameter of the beam, d = 300 mm Permissible stress, δpermissible = 80 N/mm2 To find - What…

Q: request 3.3. A T-shaped cross-section beam is loaded as shown in Figure P8.11. Find the maximum…

A: Given:- The magnitude of the uniformly distributed load = w = 80 kN/m The moment at the free-end =…

Q: Column Design: Given: a solid circular column carrying a compressive load of 8500 lb with pinned…

A: Given, SAE 4140 OQT 1000 steel

Q: Find the reactions at points A and B: 4 * A F=goolb. + 5 F=750lb 2-6" 5" 9=45010 1 B +

A: Objective: To determine the reactions at point A and B. The free body diagram of the given…

Q: A load P is supported by a structure consisting of rigid bar BDF and three identical 15-mm- diameter…

Q: Find azimuth EA and AE

A: The azimuth of AE can be determined by summing the bearing AB and interior angle of A.

Q: The process of submitting a proposal (tender) to manage a construction project a. Negotiation b.…

Q: Compute the elevations of BM2? STATION BM 1 TP 1 TP 2 TP 3 TP 4 BM 2 BS 2.71 3.62 3.51 3.17 1.47 HI…

A: Given,

Q: Consider the stratified soil sample shown below with k₁ = 0.01 cm/sec, k₂ = 0.02 cm/sec, H₁ = 10 cm,…

Q: Refer to the figure shown. Given a W8x48 A992 steel with 2-49 in, which of the following statements…

Q: In the fig. Given, 1. Write the shear and moment equations between change of load points. 2. Without…

A: Given:- To find:- Shear and moment equations Shear force and moment diagram for the beam when an…

Q: Through a very narrow gap of height h, a thin plate of large extent is pulled at a velocity V. On…

Q: For the shown force vectors, determine: 1) The coordinate direction angles of (FR) 2) The angle (0)…

A: Given: Required: Coordinate direction angles Angle between F and P

Q: 1.(e) The state of plane stress shown occurs at a critical point of a steel machine component. As a…

Q: At the instant shown, 6 = 60°, and rod AB is subjected to a deceleration a= 16 m/s² when the…

Q: Problem 2: Member AC is subjected to a vertical force P= 3000 N. This force is positioned as shown…

Q: Q2 A flexible pavement is constructed with 5 inches of hot mix asphalt wearing surface (material…

A: Flexible Pavement: Flexible pavement is made out of a bituminous material surface course and basic…

Q: An extended layer of soil with homogeneous rounded grains has 10% of the material finer than 0.07…

A: Given: Homogenous rounded grains have 10 % The material finer than 0.007 mm Permeability has been…

Q: At pH 5-7 aluminum hydroxide is O readily exceeding water quality limits for aluminum O leaving a…

A: 1. At pH 5-7, aluminum hydroxides are in their least soluble form. At a pH range of 5-7, the…

Q: Calculate the leveling error in feet due to Earth curvature and light refraction (c + r) for the…

A: The question has asked to find out the levelling error due to Earth Curvature and light refraction.…

Q: The dimensions shown below are in meters. What is the pressure in kPa at point D if specific gravity…

A: Assuming atmospheric pressure as 0 kN/m2 Pressure at A = Pressure at O + Pressure of Oil Column…

Q: Many engineers inadvertently create mass wasting when they build highways. What’s the error they…

A: Inadequate drainage management is a typical mistake made by engineers while designing roadways that…

Q: The concentration of ultimate BOD in a river entering the first of two lakes connected in series is…

A: Given, Concentration of BOD at entrance = 20 gm/m3 Rate coefficient, k = 0.35 d-1 Flow rate (Q) =…

Q: A 20 m long steel rod is at a temperature of 20°C. The rod is heated so that temperature rises by…

A: Given data- 20 m long steel rod at temperature = 20oC Temperature rises to 50oC Rod can expand upto…

Q: A secondary road in a developing country, 30 km long is to be improved by surface treating the…

A: Given length of road = 30 km cost of improvement = $150,000/- per km Total cost of improvement for…

Q: - Change the magnitude of 10 kip to 7.9 kip - Change the outer width of the cross section from 6 in…

A: Given:- Cross section of the beam is To find:- Maximum in plane shear stress at point A Principal…

Q: Choose all that apply. The vules of K for effective length of a column when studying its buckling:…

Q: In the fig. Given, 1. Write the shear and moment equations between change of load points. 2. Without…

A: Given: Required: Shear and moment equations Shear and moment diagram , when an additional 5 KN…

Q: 2Mo L Mo B - Determine the equations of the elastic curve and determine the maximum deflection. El…

A: Given Data EI = Constant Determine a. Slope and Elastic curve (deflection) equation using double…

Q: A rectangular concrete channel 5m wide carries water as shown in the figure below. The channel bed…

A: GIVEN : WIDTH ( B )= 5 m SLOPE OF BED = 0.0013 TO FIND DISCHARGE ( Q )

Q: Determine the probable error and relative precision of the underlined distances and the mean of the…

Q: Q. A saturated sand sample has dry unit weight of 20 kN/m³ and a wwwww specific gravity of 2.5. If…

A: Given - Weight of sand sample, Yd = 20 kN/m3 Specific gravity, G = 2.5 Yw = 10 kN/m3 To find - What…

Q: In a 90° triangular notch, the error in the estimated discharge for a given head due to an error of…

A: Given: A 90o triangular notch. The error of 1% in cutting the vertex angle. The error is estimated…

Q: The open channel shown has a flow of 30 cfs with n = 0.018. Compute the required 1/2 slope. 2.5 ft 5…

Q: Consider the geometric and traffic characteristics shown below. Approach (Width) North (56 ft) South…

A: Since the solution for the given question is lengthy, so the first 6 parts will be solved below.…

Q: For the beam illustrated in the figure, find the locations and magnitudes of the m sile bending…

Q: Q. The void ratio of the soil sample is 2. What is the corresponding porosity of the samle?

Q: Compute for the ultimate moment capacity of an am simply supported steel beam with the properties…

A: Answer (a) Unbraced length Lb =3 m, Cb =1 Lp = 1.76ryEFy Lp = 1.76*21.51200000250 Lp = 1070.77 mm…

Q: A 16 ft long Hem Fir, Select Structural Grade 8 x 12 shrinks 1/16" in length under an axial…

Q: What is the minimum stopping sight distance on a -3.5% grade for a design speed of 110 kmph ?…

A: Given: Slope grade = -3.5% Design speed, v=110 kmph Coefficient of friction between tires and…

Q: 3 Determine the support reactions the beam shown here: 9 = 450 น max A 12 hint: 6 resultant force is…

A: Given-

Q: A steel wire of length 2.0 m is subjected to tension and produced an elongation of 3 mm. What should…

A: Given:- Length of steel wire = 2 m Elongation in the wire = 3 mm Original diameter of wire = 1.5 m E…

Q: Question 03: Determine the normal stress and draw the stress diagram of the beam at a point 1 m from…

A: Given data in question Load 20 kN/m Span 2 m MOI 225×106 mm4 Depth 300 mm To find out Normal…

Q: A prestressed concrete beam is simply supported over a span of 11 m. the beam is reinforced with…

A: A) Given data : Span, L=11m = 11000mm…

Q: Problem Statement Based on Problem 8-11 from the textbook. The man has a mass, m. He plans to scale…

Q: Exercise 1 Directions: In an A4 size bond paper, analyze a compound truss. Exercise 2…

A: Compound Truss A Compound Truss is a type of truss structure that consists of two or more simple…

Q: A simple supported floor joist with a section shown has a span length of 4.3m. The total dead load…

Q: 1. A hydraulic punch press is used to punch a slot in a 10-mm-thick plate, as illustrated plate…

Q: Calculate the total discharge throughout the section presented below, based on the measurements…

Q: A pin-connected structure is supported as shown in the figure. Bar (1) is made of brass [E = 105…

Concept explainers

Properties of materials

A property of a material describes its characteristics and distinguishes it from the others. The material properties are described it in terms of its hardness, color, appearances, and so on. The material properties generally depend on the type of material, or whether it is a metal or an alloy. There are different kinds of material properties such as mechanical properties, thermal properties, physical properties, and chemical properties. Chemical properties describe the material in terms of a chemical change. The mechanical properties come into existence when the material is acted upon by an external load. Thermal properties are associated with the temperature of the material and specific heat.

Question

PROBLEM SOLVING 2
The plates are connected by
12-mm bolts in Figure 5. The
maximum axial stress of each
plate is 20 MPa and the
maximum shear stress of each
bolt is 14 MPa. Determine the
maximum Force F that can be
applied to the plates.
F
F
340 mm
D
340 mm
Figure 5: Bolted Plates
F 150 mm
F
50 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

I Example 2 W SECTION The hanger below (front view and side view) supports a 5000 N partition wall. Calculate the normal stress in the angles if they are 76 x 76 mm with a thickness of 9.5 mm. Calculate the shear stress in the bolts, the bearing stress on the gusset plate and on the angles. PL120X10 220 A325M BOLTS 2- L76x76x9.5 T, O O O O
The following image shows a front and side view of the column connection. The bolts have a diameter of ¾”. The W12X65 profile has a thickness of 0.605”. Determine: a. The shear stress in the bolts. Answ. 11.81 ksi b. The axial stress in the bolts. Answ. 23.62 ksi c. The support stress in the W12X65 profile. 11.50 ksi
ll zain IQ 37 MPa no one 10/10 find the tensile stress in upper plate in section 3-3 5 1 4 80 kN 80 kN B-bolt DIA. 10 MM 80 kN 80 kN B-bolt DIA. 10 MM 10 MPa 12.5 MPa 15 MPa 8.5 MPa no one 10/ find the bearing stress between bolts and plate
Given the following allowable stresses:• 50 MPa for shear in rivets• 100 MPa for bearing between a plate and a rivet• 80 MPa for tension in the platesDetermine the maximum load P that can be applied to the lap joint connected bythree – 16 mm diameter rivets. Note: Draw its FBD
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. Use a501 plate and a502 gr2 rivet a. Determine maximum load P without exceeding allowable tensile stress on plate b. Determine maximum load P without exceeding allowable shear stress on rivets c. Determine maximum load P without exceeding allowable bearing stress between plates and rivets
Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
Determine the design tensile strength of the 12 in. x 1/2 in. steel plate shown in the figure. The bolts are 3/4 in. diameter. The steel is A572 Gr. 50. Check yielding and fracture. Check Block Shear. T 3in. 73im 13in 1 3in t
4. Six rivets are used in the connection shown in the figure. If both P= 50 kN, what is the minimum diameter P- 50 rivet is necessary so as not to exceed the 70MPA allow shearing stress? What thickness of plate is required so as not to exceed a bearing stress of 140 MPa? 80 mm 80 mm Ps so 100 mm
ZAO O "l zain IQ YA docs.google.com/forms 10/.. find the shear stress in bolts 2 3 1. 5 4 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 110 MPa. 127 MPa. 509 MPa no one 0/10 find the tensile stress in upper plate in section 1-1 (2 (5 (3 1 4) + ...
The following image shows a front and side view of the column connection. The bolts have a diameter of ¾”. The W12X65 profile has a thickness of 0.605”. Determine:a. The shear stress in the bolts.b. The axial stress in the bolts.c. The support stress in the W12X65 profile.
ACTIVITY The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with thickness shown in the figure. The working stresses are 70MPa for shear in rivet and 140MPa for bearing stress due to the rivets. How many 19-mm diameter rivets are required to fasten the said members to the gusset plate? K.R.R.P. wwwwwwww 00 400 4m B 3m C 96KN 4m 6m 200KN E Am 3m F 96KN 4m H DETAIL OF JOINT B 75X75X6 mm ------------- · ET---- I 14 mm thick GUSSET PLATE P BC 75X75X13 mm P BE