Q3// Answer A or BAll The plant capacity factor of power plant 50%, the peak load is 30MW, the loadfactor is 60% and plant use factor 80%. Find: the daily output power and the plantreserve capacity.B// What are the methods of draught in cooling towers. Demonstrate them withdrawings. What is the relationship between the cooling tower and condenser.

Answered: Image /qna-images/answer/ad15ebd3-2f31-44fa-8691-df80e9a37da8.jpg

Answered: All The plant capacity factor of power…

All The plant capacity factor of power plant 50%, the peak load is 30MW, the load factor is 60% and plant use factor 80%. Find: the daily output power and the plant reserve capacity.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 1 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Pump work in KW. Ans. Ideal heat rate in KJ/KW-hr. Ans. Rankine engine efficiency (%). Ans. Cycle thermal efficiency ( %). Ans
A performance test of an ice plant gave the following data: Capacity: 20 tons of ice/day Refrigerant: Ammonia Condenser pressure: 1391.5 kPa Evaporator pressure: 208.26 kPa Raw water temperature: 32OC Harvest temperature: -7OC Block of ice: 300 lb/block The compressor is twin-cylinder, single acting, D/L = 1.25, 450 rpm, mechanical efficiency is 80%. Additional heat load due to infiltration and conduction is 20%. Determine: a) Number of cans needed b) Product cooling load c) Refrigerating capacity in tons of refrigeration d) Amount of refrigerant flow e) Size of motor to drive the compressor f) Bore diameter and length of stroke
Exampie Air conditioning unit uses Freon R-22 for conditioned office at 25 C. The evaporating temperature is 17 C and the condensing temperature is 47 C. The compressor is reciprocating and single acting with number of cylinders of 4, volumetric efficiency of 0.9, number of revolution is 900 rpm cylinder dimensions of L/D is 1.25. If the compressor power is 3 kW and mechanical efficiency of 0.9, estimate the followings: the refrigerant mass flow rate in kg/min, refrigeration capacity in TR, cylinder dimensions, condenser heat load, coefficient of performance and relative efficiency. and
5. Sketch a Rankine eycle on T-s diagram and derive the thermal efficiency for a rankine eycle from its 4 steps. Show on T-S plot and discuss what is the effect of a. Increasing superheat b. decreasing condenser pressure c. Adding friction at pump and turbine
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 16.3846 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: PV and TS diagrams of the cycle showing ideal and actual process lines Heat rejected at condenser (KJ/sec). Ans.____________________________ Mass of cooling water in kg/sec if cp H2O = 4.18 KJ/kg-K, and inlet temp of water to condenser = 20 deg C, outlet temp is 35 deg C. Ans.___________________________
The air outside is 40 C and 60% r.h. I want torun an air conditioner to cool it to 15 C. The deliver rate should be 1000 m^3/min. What is Q and the rate at which water condenses (if any)?
8.3 A four-effect evaporator is being considered for concentratinga fruit juice that has no appreciable boiling-point elevation.Steam is available at 143.27 kPa, and the boiling point ofthe product in the fourth effect is 45°C. The overall heat-transfer coeffi cients are 3000 W/(m 2 °C) in the fi rst effect,2500W/(m2 °C) in the second effect, 2100W/(m2°C) in thethird effect, and 1800W/(m2°C) in the fourth effect. Calculatethe boiling-point temperatures of the product in the fi rst,second, and third effects. Assume the heating areas in all theeffects are equal to 50m2 each. The mass fl ow rate of steam tothe fi rst effect is 2400kg/h, the feed rate to the fi rst effect of 5%total solids fl uid is 15,000kg/h, the concentrated product fromthe fi rst effect leaves at 6.25% total solids, and the concentrationof product leaving the second effect is 8.82% total solids. Make it in the form of a spreadsheet for solving the example problem no. 8.2 and 8.3
In a certain refrigeration system for low temperature application, a two stage operation is desirable which employs refrigerant 22 system that serves a 30 ton evaporator at -30 degree celcius. This system uses direct contact cascade condenser with a condenser temperature of 40 degree celcius. Find: A) Mass flow rate at the low pressure loop (m1) B) Mass flow rate at the high pressure loop (m5) C) Compressor work at the low pressure side. E) Compressor work at the high pressure side. F) Total Work G) Condenser Work H) COP
A steam plant that could increase the thermal efficiency by using waste heat from the turbune is an example of while that that could use the electical output from the turbine to generate steam to the system is an example of A toy called Drinking bird is an example of (PMM1/PMM2/PMM3/niether of the two) because the power source is (powered by water in the cup/ powered internally my the movement/ none of the option).
Please find the highest thermal efficiency possible, while remaining within the boundaries. What is required: -Power produced must be at least 60 Mega Watts -Thermal efficiency must be greater than 36% -Back-work ratio must be smaller than 48% Assume: -air is the working fluid -specific heats vary with temperature (use table A-17) -Compressor inlet is at 1atm and 300k -the combustion process is isobaric and is modeled as a heat exchanger -Turbine exhaust is the same pressure as compressor inlet Compressor specifics: -Max volume flow rate (m^3/h) = 600,000 -Max outlet pressure (atm) = 12 -Isentropic efficiency = 90% Combustion chamber and gas tubine specifics (Note these come as a set) -Max pressure = 16.7 atm -Max temp = 1500 (celcius) -Turbine isentropic efficiency = 92% -Max heat rate = 230MW
Homework-2 Compute the themal e fficiency of an ideal Ran kine cycle for which the steam leavea the boiler as Saturated Vapor at 30 bars. The turbine-outlet Conditions is Be1 bar. Determine the mass floo rate of the steam in kg/hr, net Power output of the cycle is 50000 Sehematic ond given data are: 1f the kw. The TI= 5002 P 3०bars %3D 9in (saturated) vapour 30 bars 2 PR =0-1 bar 4 Pa=30 bas o-1 bar +4 Tout 3 (Saturated liquid) Wp ( Simple Ideal Power cycle) (T.S. diagram e)
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 1 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Ideal turbine work (KW). Ans.____________________________ Heat rejected at condenser (KJ/sec). Ans.____________________________ Mass of cooling water in kg/sec if cp H2O = 4.18 KJ/kg-K, and inlet temp of water to condenser = 20 deg C, outlet temp is 35 deg C. Ans.____________________________ Pump work in KW. Ans.___________________________