(a) What is the change in length of the bar? (b) What should be the additional magnitude to be added to load applied at D supposed the bar does not change in length? (c) Supposed the bar does not change in length, the applied load at D remains 1300 lb, and the areas for segment AB and BC remain 0.40 in?, determine the revised area for segment CD.

(a) What is the change in length of the bar? (b) What should be the additional magnitude to be added to load applied at D supposed the bar does not change in length? (c) Supposed the bar does not change in length, the applied load at D remains 1300 lb, and the areas for segment AB and BC remain 0.40 in?, determine the revised area for segment CD.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I RevieW The 1.16-in.-diameter rod in (Figure 1) is subjected to the loads shown. Part A Determine the state of stress at point B. Express your answers, separated by commas, to three significant figures. IVα ΑΣφ. vec ? OB =, (Tzy)B =, (T2)B = ksi (C), ksi, ksi Figure 1 of 1 > Submit Request Answer < Return to Assignment Provide Feedback 9 in. 200 lb 300 lb 1200 lb in.
Problem (3): Two gage marks are placed exactly 280 mm apart on 22 mm diameter solid metal rod. When an axial tension force 70 kN is applied to rod, the distance between the gage marks is measured as 280.57 mm. determine the modulus of elasticity of the metal in units of GPa. 70 kN 70 kN 280 mm
Q.3) The original and deformed geometries of a Plastic block subjected to axial and shear stresses is shown below. Determine the average normal strains along diagonals AB and CD. Also find shear strain Yxy at each of its corners A, B, C and D. y D' 107 mm A D 91.5° 100 mm 5 mm B' B 100 mm C' 12 mm
The beam is subjected to a shear of V = 13.5 kN. Set w = 125 mm. (Figure 1) Part A Determine the web's shear stress at A. Express your answer to three significant figures and include the appropriate units. HA igure 1 of 1> Value Units 200 mm Submit Request Answer 30 mm Part B 25 mm Determine the web's shear stress at B. Express your answer to three significant figures and include the appropriate units. 250 mm HẢ 30 mm Value Units
3. Sample of steel bar has 12 mm diameter after performing tension test the failure load was 57 KN, tensile strength of this sample equal to * 504.24 MPa. 504.56MPA O 505.1MPA 503.24MPA All above are not correct
draw the digram and calculate the forces
Vn = 6*36*1/(4*1.1) = 49.09 am I wrong? I believe in the calculation in the solution the coefficient m was not taken into account. And Pn is not 54 kips either, with the given formula it comes up as 6*36*0.5/(4*1.25) = 21.6 and in which case the design strength would be 21.6 kips. Please let me know if there's something I'm missing from the formulas.
B= 9 A=9 Y=200 show FBD and complete solutions pls
Consider the object shown in (Figure 1). Suppose that P = 310 N, M = 810 N •m. Follow the sign convention. Part A Determine the internal normal force at point C. Express your answer to three significant figures and include the appropriate units. ? Nc = Value Units Submit Request Answer Part B Determine the internal shear force at point C. Express your answer to three significant figures and include the appropriate units. HẢ ? Vc = Value Units Figure Submit Request Answer 1 of 1 Part C Determine the internal moment at point C. B E P Express your answer to three significant figures and include the appropriate units. 1 m HA ? D 1 m 1 m 2 m M Mc = Value Units Submit Request Answer
The lower ends of the 3 bars in the figure are at the same level before the rigid homogenous 18Mg block is attached. Each steel bar has an area of 566mm^2 and E=200Gpa. For the bronze barn the area is 866mm^2 and E=83Gpa. Find the stresses developed in each bar.
Given: TABLE 3.1. Coefficients for Rectangular Bars in Torsion a/b C2 1.0 * 0.208 0.1406 L 1.2 0.219 0.1661 0.1958 1.5 0.231 2.0 0.246 0.229 0.249 2.5 0.258 3.0 0.267 0.263 4.0 0.282 0.281 0.291 0.312 5.0 0.291 L 10.0 0.312 00 0.333 0.333 T Wood: Allowable stress: 5 MPa Shear Modulus: 0.5 GPa L= 0.6 m d = 50 mm What is the largest safe torque, in Nm, can be applied to the circular cross- section? (Provide answer in whole numbers, without the units. Ex: 123.4 Nm - -> 123) Your answer What is the largest safe torque can be applied to the rectangular cross-section? (Provide answer in whole numbers, without the units. Ex: 123.4 Nm --> 123) Your answer
Determine the largest torque T which may be applied to end of the solid bar which is shown in the diagram below, knowing that the maximum allowable shear stress = 107MPa and G = 40GPa. Provide your answer in kNm with precision to two decimal points. B 40 mm TABLE 3.1. Coefficients for Rectangular Bars in Torsion a/b C₁ C₂ 1.0 0.208 0.1406 1.2 0.219 0.1661 60 mm 1.5 0.231 0.1958 2.0 0.246 0.229 2.5 0.258 0.249 3.0 0.267 0.263 4.0 0.282 0.281 5.0 0.291 0.291 N 10.0 0.312 0.312 مة 0.333 0.333