1. For the beams shown below: (a) calculate the support reactions. (b) calculate the internal forces at sections A and B and indicate if the internal forces are positive or negative. F = 40 lb F, = 30 lb dj = 20' – 0" dz= 10' – 0" A F, = 30 lb F, = 40 lb 8' - 0" 17' - 0" 3' – 0" 7' -0" 5' - 0" 10 kips 3 kips/ft 8' – 0" 8' – 0" - 3'

1. For the beams shown below: (a) calculate the support reactions. (b) calculate the internal forces at sections A and B and indicate if the internal forces are positive or negative. F = 40 lb F, = 30 lb dj = 20' – 0" dz= 10' – 0" A F, = 30 lb F, = 40 lb 8' - 0" 17' - 0" 3' – 0" 7' -0" 5' - 0" 10 kips 3 kips/ft 8' – 0" 8' – 0" - 3'

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Refer to the figure below and using the following:F1= 8 kNF2 = 10 kNa = 2 mb = 2 mWhat gives the axial force for members DE, BC, EF, GCWhat gives the reaction at the pin support?
QI Figure 1 shows a pin connceted members of truss. The truss is loaded with 20 kN box through a frictionless pulley at point D (20 kN) and concentrated laod at C 10 kN. As you are structural engineer, you are required to do the following: i) Determine the reaction of at A and B? ii) Determine the internal force OF all members? + 3m + 12 20 kN 5 m 10 kN 3 m B 135 6 m Figure 1
Q 3. A rigid beam AB is 5.5 m long, hinged at point A and supported by two pipes at C and D as shown in figure 3 below. Pipe 1 at C is of copper has a outer diameter of 120 mm and inner diameter of 100 mm and yield stress of copper is 138 N/mm² Pipe 2 at D is of steel has a outer diameter of 100 mm and inner diameter of 90 mm and yield stress of steel is 250 N/mm2 Calculate the safe load at A if the load factor is 1.66 Pipe 1 Pipe 2 Psafe 2.3 m 2 m C 5.5 m Angle ACE = 0 Figure 3 Angle BDF = 42° Take 0 = 10 Page 7 of 7 PTO
The members of the truss are 25mmx50mm in cross section. Determine the maximum load P that can be applied so that the stresses will not exceed 100 MPa in tension or 70 MPa in compression. See figure 101. Figure 101 A 0 2m P B 2.5m 1.5m C
Calculate the support reaction at roller support A
The steel rod is fixed to the side at ‘A’, and before it is loaded, there is a gap of 0.15-mm between the side at ‘D’ and the other end of the rod at ‘C’ as shown in the figure below. Determine the support reactions at ‘A’ and ‘D’ if the rod is subjected to an axial force, ? = 200-??. Take ??? = 200-???.
given the image, find the support reaction components at the pin joint A and the roller B 2 m 5 KN 7 kN•m 2m SIN
4. Find the force acting in Bar AC,CE & CD of the compound Truss and the reactions at A & F as shown in the below figure. 180 lb 540 lb 10 10 D 10 A E F 18' RA RE B.
1. For the beams shown below: (a) calculate the support reactions. (b) calculate the internal forces at sections A and B and indicate if the internal forces are positive or negative. F₁ = 40 lb F₂ = 30 lb 8'-0" A d₁= 20'-0" 17'-0" B F₂ = 30 lb 3¹-0" d₂= 10'-0" F₁ = 40 lb 7'-0" 5'-0"
A prismatic bar is fastened between two rigid walls at A and B and subjected to loads as shown in figure below. Determine the reactions at supports. D RA 80 mm C 15 KN 150 mm 25 kN 250 mm B RB
Determine the magnitude of the pin force at A. Assume W = 845 Ib, a = 3.0 ft, b = 2.0 ft, r = 9 in. a a C В A W D Answer: A = i Ib
Using the method of joints, determine the force in each member of the truss shown below (solve for FAB, FAD, FBD, FDE, FBE, FBC, and FcE. Use the sign convention of negative for compression of the joint and positive for tension of the joint. 2000 lb -12 ft- 1000 lb 12 ft cl 8 ft D E -12 ft 6 ft 6 ft Hints: 1. The reaction at the roller support at E is 10,000 lbf upwards. 2. The reaction of the support at C is 7,000 lb, downwards.