6 Ohm 1 mH 18 VI50 Hz/0 Deg 3 A/50 Ha0 Deg 1 uF Ohm Fig.2 Tablel Measured values Zth Eth Itoad Calculated values Zth Itoad Discussion 1. Calculate thevenin impedance Zth and record the value in table 1 2. Calculate thevenin voltage source Eth and record the value in tablel 3. Calculate the current through the load 22 resistance then record the value in table 1 4. Discuss the result.

6 Ohm 1 mH 18 VI50 Hz/0 Deg 3 A/50 Ha0 Deg 1 uF Ohm Fig.2 Tablel Measured values Zth Eth Itoad Calculated values Zth Itoad Discussion 1. Calculate thevenin impedance Zth and record the value in table 1 2. Calculate thevenin voltage source Eth and record the value in tablel 3. Calculate the current through the load 22 resistance then record the value in table 1 4. Discuss the result.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

What will be the value of the twiddle factor: W42
For figure (1)draw and calculate the voltages waveform across each half of secondary winding and across load when 100sin2π60t applied across the primary, then find PIV.
6. What is the effect of load inductance on the ripple current? 7. i effect of chonnine Bock and boost 8. Wh 9 What chopping 10. At what duty evcle does the load current rinnle current he
In the figure: R1 = 1439.170, R2 = R1 and R3 =2R2, then determine the value of the voltage source E. a 8 mA 10 mA 2 mA RT R1 R2 R3 O 25.33 11.51 O 17.27 15.43 13.82 +
If the voltage V, = 800 mV, then the current flowing in the load I, is: %3D -j20n Select one: O a. None of these O b. Is 100 <-90° mA O c. Is 5.0<.-90° A O d. Is 5 <90° mA ell
If T = 0.6Z – 60° and A = 48cm find the position of the first voltage minimum on the line. Select one: O a. The first voltage minimum is at 2cm from the load. O b. The first voltage minimum is at 72cm from the load. O c. The first voltage minimum is at 8cm from the load. O d. The first voltage minimum is at –4cm from the load. O e. The first voltage minimum is at 20cm from the load. O f. The first voltage minimum is at 32cm from the load. O g. The first voltage minimum is at 44cm from the load. O h. The first voltage minimum is at 24cm from the load.
3. The secondary voltage can rise above its rated value when the load is a. resistive. b. capacitive. C. inductive. d. an RL series combination.
a) What is the peak voltage across R2? b) What is the RMS value of I1?
Solution all part
Calculate the RMS current through R2 in the diagram IR1 = 6.06mA peak, R2 = 2.7 kohms, total current is 9.522mA RMS 3.25mA RMS 5.24mA RMS 7.41mA RMS 9.0mA RMS
1. A load of 50 ohms resistance and 0.4 H inductance are connected in series to 100 volts, 60 hz a-c source. What must be the value of the capacitance to be connected in parallel to the circuit to raise the power factor to 0.96 lagging. Draw the circuit diagram.
Use the information below to answer questions 24 und 25. The voltage across and the current through a load are (10+ j5Y and (2-jiArespecively. 24. What is the reactive power in VArconsumed? D. 0 A. 15 C. 20 D. 25 25. What is the pawer factor of the load? A. 0.8 leading B. 0.8 Jagging. -D. 0.6 ligging C 0.6 leading