Concept explainers
Solve Prob. 17.11, assuming that the 6 N·m couple is applied to gear B.
17.11 Each of the gears A and B has a mass of 10 kg and a radius of gyration of 190 mm, while gear C has a mass of 2.5 kg and a radius of gyration of 80 mm. If a couple M of constant magnitude 6 N·m is applied to gear C, determine (a) the number of revolutions of gear C required for its angular velocity to increase from 450 rpm to 1800 rpm, (b) the corresponding tangential force acting on gear A.
Fig. P17.11
(a)
Find the number of revolutions required for gear C.
Answer to Problem 17.12P
The number of revolutions required for the gear C for the work to be done is
Explanation of Solution
Given information:
The mass of the gear A is
The mass of the gear B is
The radius of gyration of the gear A is
The radius of gyration of the gear B is
The mass of the gear C is
The radius of gyration of the gear C is
The radius of the gear A is
The radius of the gear B is
The radius of the gear C is
The magnitude of the couple moment applied at point B is
Calculation:
Find the mass moment of inertia of gear A
Substitute 10 kg for
Find the mass moment of inertia of gear B
Substitute 10 kg for
Find the mass moment of inertia of gear C
Substitute 2.5 kg for
The gears A and C are in contact.
Use the kinematics concept;
Substitute 250 mm for
The gears B and C are in contact.
Use the kinematics Equation:
Substitute 250 mm for
Find the total kinetic energy
Substitute
When the angular velocity is at 450 rpm:
Substitute 450 rpm for
When the angular velocity is at 1800 rpm:
Substitute 1800 rpm for
Find the work done
Here, the number of revolution at gear B is
Substitute
Write the equation of work and energy for the system using the equation.
Substitute 146.03 J for
Find the number of revolution at gear C
Substitute 58.1 rev for
Therefore, the number of revolutions required for the gear C for the work to be done is
(b)
Find the tangential force acting on gear A.
Answer to Problem 17.12P
The tangential force acting on gear A is
Explanation of Solution
Given information:
The mass of the gear A is
The mass of the gear B is
The radius of gyration of the gear A is
The radius of gyration of the gear B is
The mass of the gear C is
The radius of gyration of the gear C is
The radius of the gear A is
The radius of the gear B is
The radius of the gear C is
The magnitude of the couple moment is
Calculation:
Refer to part (a) calculation;
The number of revolution in the gear A is equal to the number of revolution in the gear B.
Substitute 365.08 rad for
Find the total kinetic energy
When the angular velocity is at 450 rpm;
Substitute
When the angular velocity is at 1800 rpm;
Substitute
Find the work done
Here, the magnitude of couple moment at gear A is
Substitute 365.08 rad for
Write the equation of work and energy for the system using the equation.
Substitute 64.133 J for
Find the tangential force
Substitute
Therefore, the tangential force acting on gear A is
Want to see more full solutions like this?
Chapter 17 Solutions
Vector Mechanics for Engineers: Statics and Dynamics
Additional Engineering Textbook Solutions
Fundamentals Of Thermodynamics
Fox and McDonald's Introduction to Fluid Mechanics
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
Applied Fluid Mechanics (7th Edition)
Introduction To Finite Element Analysis And Design
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
- The flywheel of a small punch rotates at 300 rpm. It is known that 1,800 ft lb of work must be done each time a hole is punched. it is desired that the speed of the flywheel after one punching be not less that 90 percent of the original speed of 300 rpm. A. Determine the required moment of inertia of the flywheel. B. If a constant 25 lb ft couple is applied to the shaft at the flywheel, determine the number of revolutions which must occur between each punching, knowing that the initial velocity is to be 300 rpm at the start of each punching.arrow_forward4. Each of the gears A and B has a mass of 2.4 kg and a radius of gyration of 60 mm, while gear C has a mass of 12 kg and a radius of gyration of 150 mm. A couple M of constant magnitude 10 Nm is applied to gear C. Determine (a) the number of revolutions of gear C required for its angular velocity to increase from 100 to 450 rpm, (b) the corresponding tangential force acting on gear A. В S0 mm, S0 mm 200 mm. Marrow_forwardEach of the gears A and B has a mass of 2.4 kg and a radius of gyration of 60 mm, while gear C has a mass of 12 kg and a radius of gyration of 150 mm. A couple M of constant magnitude 10 N.m is applied to gear C determine a ) the number of revolutions of gear C required for its angular velocity to increase from 100 to 450 rpm, (b) the corresponding tangential force acting on gear A.arrow_forward
- Each of the gears A and B has a mass of 10 kg and a radius of gyration of 190 mm, while gear Chas a mass of 2.5 kg and a radius of gyration of 80 mm. Consider that a couple M of constant magnitude 10 N-m is applied to gear C. 250 mm 250 mm 100 mm Determine the corresponding tangential force acting on gear A. The corresponding tangential force acting on gear A is 26.35 O N.arrow_forwardThe flywheel of a small punch rotates at 300 rpm. It is known that 1800 ft.1b of work must be done each time a hole is punched. It is desired that the speed of the flywheel after one punching be not less than 90 percent of the original speed of 300 rpm. (a ) Determine the required moment of inertia of the flywheel. (b) If a constant 25-1b.ft couple is applied to the shaft of the flywheel, determine the number of revolutions that must occur between each punching, knowing that the initial velocity is to be 300 rpm at the start of each punching.arrow_forwardLocate mass A at 35 mm from support X. 4.4. Locate mass B at 96.5 mm from support X. 4.5. Locate mass C at 122.7 mm from support X. 4.6. Position mass A at zero degrees and D at 90o from A. 4.7. Rotate the shaft by hand and release it. As the shaft is released masses should remain in any angular position. 4.8. Change the angular position of masses B and D till the shaft is statically balanced. 4.9. Rotate the shaft with the motor at high speed and notice the reaction of the system. High vibration and noise indicate that the system is out of balance. 4.10. Change the position of the mass D till the system is dynamically balanced.arrow_forward
- The flywheel of a punching machine has a mass of 300 kg and a radius of gyration of 600 mm. Each punching operation requires 2500 J of work. (a ) Knowing that the speed of the flywheel is 300 rpm just before a punching, determine the speed immediately after the punching. (b) If a constant 25-N.m couple is applied to the shaft of the flywheel, determine the number of revolutions executed before the speed is again 300 rpm.arrow_forwardB/s Q-e.jpg The electric motor exerts a 220 N m-torque on the aluminum shaft ABCD when it is rotating at a constant speed. Knowing that G = 27 GPa and that the torques exerted on pulleys B and C are as shown, determine the angle of twist between (a) B and C, (b) B and D. 100 N. m 120 N. m 50 mm B 1 m 40 mm 1 m ...arrow_forwardProblem (1) Gears A and B each have a mass of 4 kg and a radius of gyration of 75 mm about their centers, while gear C has a mass of 15 kg and a radius of gyration of 180 mm about its center. A couple moment M = (0.20) N-m is applied to gear C. Determine the number of revolutions gears A and B experience if gear C increases its angular velocity from 25 rpm to 500 rpm. B 80 mm S0 mm 200 mmarrow_forward
- Gears A and B each have a mass of 2.4 kg and a radius of gyration of 60 mm, while gear C has a mass of 12 kg and a radius of gyration of 150 mm. A torque M with constant magnitude of 10 N.m to gear C. Determine a) the number of revolutions of gear C that is required for its angular velocity to increase from 100 to 450 rpm. b) the corresponding tangential force acting on gear A Please include the free body diagram if necessary.arrow_forwardThe flywheel of a small punch rotates at 300 rpm. It is known that 1800 ft - Ib of work must be done each time a hole is punched. It is desired that the speed of the flywheel after one punching be 90 percent of the original speed of 300 rpm. Determine the required moment of inertia of the flywheel. Use the principle of work and energy. (Answer: I = 19.20 lb - ft - s? )arrow_forwardA 255-lbf block is suspended from an inextensible cable which is wrapped around a drum of 1.75-ft radius rigidly attached to a flywheel. The drum and flywheel have a combined centroidal moment of inertia 12 lb . ft . s 2 . At the instant shown, the velocity of the block is unknown directed downward. Knowing that the bearing at A is poorly lubricated and that the bearing friction is equivalent to a couple M of magnitude 65 lb .ft, determine the velocity of the block before it has moved 3.5 ft downward if at S2 speed is 13.5ft/sarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY