Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
10th Edition
ISBN: 9780073398204
Author: Richard G Budynas, Keith J Nisbett
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 1, Problem 12P
A solid circular rod of diameter d undergoes a bending moment M = 1000 Ibf · in inducing a stress σ = 32M/(πd3). Using a material strength of 25 kpsi and a design factor of 2.5. determine the minimum diameter of the rod. Using Table A-17 select a preferred fractional diameter and determine the resulting factor of safety.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A solid circular rod of diameter d undergoes a bending moment M = 113 Nm inducing a stress σ = 16M/ (πd3). Using a material strength of 172.4 MN/m2 and a design factor of 2.5, determine the minimum diameter of the rod. Using Table 1, select a preferred fractional diameter and determine the resulting factor of safety
A steel rod is subjected to a reversed axial load of 180 kN. Find the diameter of the rod for a factor of safety of 2. Neglect column action. The material has an ultimate tensile strength of 1070 MPa and yield strength of 910 MPa. The endurance limit in reversed bending may be assumed to be one-half of the ultimate tensile strength. Other correction factors may be taken as follows: For axial loading (Ka) = 0.7; For machined surface (Ksur) = 0.8 ; For size (Ksz) = 0.85 ; For stress concentration(Kf)= 1.0.3.
Find the equivalent stresses at Points 1 and 2 of the element with given geometry and loading conditions according to the Maximum shear stress hypothesis and the Maximum strain energy hypothesis.
Shaft diameter: 20 mm, Shaft Length 120 mm, F1 = 750N, F2 = 3000N, Mb = 2400 N.mm. Steel if St37 and Safety coefficient is 2 If taken, will this stick work safely under these operating conditions?
(Yield of given steel Strength 225 Mpa, Tensile strength 370 Mpa)
Chapter 1 Solutions
Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
Ch. 1 - Select a mechanical component from Part 3 of this...Ch. 1 - Select a mechanical component from Part 3 of this...Ch. 1 - Select an organization listed in Sec. 16, go to...Ch. 1 - Go to the Internet and connect to the NSPE website...Ch. 1 - Go to the Internet and connect to the NSPE website...Ch. 1 - Estimate how many times more expensive it is to...Ch. 1 - The costs to manufacture a part using methods A...Ch. 1 - A cylindrical part of diameter d is loaded by an...Ch. 1 - When one knows the true values x1 and x2 and has...Ch. 1 - Use the true values x1 = 7 and x2 = 8 (a)...
Ch. 1 - A solid circular rod of diameter d undergoes a...Ch. 1 - A fatigue test is performed on rotating beam...Ch. 1 - Determinations of the ultimate tensile strength...Ch. 1 - The lives of parts are often expressed as the...Ch. 1 - The tensile 0.2 percent offset yield strength of...Ch. 1 - A mechanical system comprises three subsystems in...Ch. 1 - From See. 3-12, the maximum shear stress in a...Ch. 1 - A round cold-drawn 1045 steel rod has a mean...Ch. 1 - A beam subjected to axial loading will experience...Ch. 1 - Three blocks A, B, and C and a grooved block D...Ch. 1 - The volume of a rectangular parallelepiped is...Ch. 1 - A pivot in a linkage has a pin in the figure whose...Ch. 1 - A circular cross section O ring has the dimensions...Ch. 1 - Prob. 25PCh. 1 - Prob. 26PCh. 1 - Prob. 27PCh. 1 - Prob. 28PCh. 1 - Convert the following to appropriate ips units:...Ch. 1 - Convert the following to appropriate SI units: (a)...Ch. 1 - Generally, final design results are rounded to or...Ch. 1 - Repeal Prob. 1-31 for the following: (a) = F/wt,...Ch. 1 - Repeat Prob. 131 for: (a) = F/A, where A = d2/4, F...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?arrow_forwardA pinned-end strut of aluminum (E = 10,400 ksi) with a length L = 6 ft is constructed of circular tubing with an outside diameter d = 1 in. (sec figure). The strut must resist an axial load F = 4 kips with a factor of safety n = 2.0 with respect to the critical load. Determine the required thickness t of the tube.arrow_forwardRepeat Problem 11.2-14 using L = 12 ft, ß = 0.25 kips/in., ßRl= 1.5ßL2, and ßR2= 2 ßR1.arrow_forward
- A pinned-end strut of a length L = 5.2 ft is constructed of steel pipe (E = 30 × 103 ksi) having an inside diameter d1= 2.0 in. and outside diameter d2= 2.2 in. (sec figure). A compressive load F = 2.0 kips is applied with eccentricity e = 1.0 in. What is the maximum compressive stress max in the strut? What is the allowable load Pallowif a factor of safety n = 2 with respect to yielding is required? (Assume that the yield stress y of the steel is 42 ksi.)arrow_forwardA high-strength steel bar used in a large crane has a diameter d = 2.00 in. (sec figure). The steel has a modulus of elasticity E = 29 × 10 psi and Poisson’s ratio is v = 0.29. Because of clearance requirements, the diameter of the bar is limited to 2.001 in. when it is compressed by axial forces. What is the largest compressive load Pmaxthat is permitted?arrow_forwardA copper alloy pipe with a yield stress aY= 290 MPa. is to carry an axial tensile load P = 1500 kN (see figure part a). Use a factor of safety of 1.8 against yielding. (a) If the thickness t of the pipe is one-eighth of its outer diameter, what is the minimum required outer diameter dmin? (b) Repeat part (a) if the tube has a hole of diameter dt 10 drilled through the entire tube, as shown in the figure part b.arrow_forward
- Solve the preceding problem if the thickness of the steel plate is. t = 12 mm. the gage readings are x = 530 × 10-6 (elongation) and y = -210 -× l0-6 (shortening), the modulus is E = 200 GPa, and Poisson’s ratio is v = 0.30.arrow_forwardRigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?arrow_forwardAn aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.arrow_forward
- The load on a helical spring is 1282 lb and the corresponding deflection is to be 3.4 inches. Rigidity modulus is 11 x 106 psi and the maximum intensity of safe torsional stress is 60,000 psi. If the wire diameter and the mean diameter are 0.5 in. and 3 in., respectively. Determine the number of active coils. Don't round your answer to preferred size. Round your answer to 4 significant figuresarrow_forwardThe figure below is subjected to a load fluctuating between Pmin and Pmax. Calculate the factor of safety n for unlimited life based on the Goodman criterion. Given D= 120 mm, d= 80 mm ,r= 16 mm, t=15 mm, Sut-700 MPa, and the reliability of 99.9%. The fillets and adjacent surfaces are ground. Pmin = 90i – 50 k (kN) and Pmax = 210i + 50 k (kN) P D Parrow_forwardCalculate the dimensions of the I-section of a connecting rod, stating any assumptions. using the data below: Maximum cylinder pressure = 3.15N/mm² Cylinder bore = 100mm Factor of Safety=6 Crank length 95mm Connecting rod length=380mm Take the constant a=7500.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Column buckling; Author: Amber Book;https://www.youtube.com/watch?v=AvvaCi_Nn94;License: Standard Youtube License