8262.5 ▸ A balanced star connected load is connected to a 4 kVA, 415 V, star connected three phase generator via a three wire transmission line. The impedance of each line is 0.3 + j6.0 ohms. The synchronous impedance of the generator is 0.4 + j2.4 ohms. The fixed losses of the generator are 175 W. The field winding is connected to a 120 V source and the field current is 5.5 A. When the generator delivers rated load at rated voltage and at 0.866 power factor lagging, find ▸ The efficiency of the generator (79.8%) The voltage regulation at the load (11.2%) ▸ The efficiency of the entire system. (79.2%) Ts = 8262.5w (401) =65.74 N.m ▸ Draw the power flow diagram of the entire power system indicating on the diagram all the values of the power flows.

8262.5 ▸ A balanced star connected load is connected to a 4 kVA, 415 V, star connected three phase generator via a three wire transmission line. The impedance of each line is 0.3 + j6.0 ohms. The synchronous impedance of the generator is 0.4 + j2.4 ohms. The fixed losses of the generator are 175 W. The field winding is connected to a 120 V source and the field current is 5.5 A. When the generator delivers rated load at rated voltage and at 0.866 power factor lagging, find ▸ The efficiency of the generator (79.8%) The voltage regulation at the load (11.2%) ▸ The efficiency of the entire system. (79.2%) Ts = 8262.5w (401) =65.74 N.m ▸ Draw the power flow diagram of the entire power system indicating on the diagram all the values of the power flows.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.23MCQ: Does an open- operation, the kVA rating compared to that of the original thr-phase bank is (a) 2/3...

See similar textbooks

Similar questions

The distribution factor for 90 slots, 10-pole, 3-phase winding is A 0.90 B 0.895 C 0.959 D 0.978
In small transformers, the total iron losses may vary from % of the rated output. O 0.5 to 1 O 0.2 to 0.6 O 0.8 to 1.5 O 04 to 1 In DC machine, are collect the current from commutator and given to the external circuit. O Interpoles O Pole shoe O Yoke O Brushes
A parallel connection of a RL branch with a C branch is connected across a 100V AC mains. At first R = 10 ohms, L = 20mH and frequency of 1000rad / s, the current measured is 2.2361A at 89.44 leading power factor. A) Determine the initial capacitance. B) However, a fault occurs on the capacitor branch making its capacitance 20% lower and a resistance of 5 ohms is detected. If this faulty circuit is rerun but at a frequency of 500 rad / s, determine the new current that will flow through the circuit.
2) 9.2Three - 25 KVA single-phase transformers are connected in delta – delta. One of the transformers has been defected. What is the maximum real power that the transformer bank can deliver at a power factor of 0.8?
The rated voltages of a single-phase transformer are 2000 V and 200 V in its primary and secondary respectively. The shunt impedance can be modelled with a resistance of 14000 ohms in parallel with a reactance of 1100 ohm, both refer to primary side. The primary and secondary series impedances are (0.12+j 0.35) ohms and (0.0012+j 0.0035) ohms respectively. A load is connected to the secondary side of transformer, draws 810 KVA with a lagging power factor of 0.85. The load voltage is same as rated voltage, that is 200 V. ▪ Use per unit method for analysis and find the voltage on primary side in pu.
sformer 1200 KVA, 11000/2200 V, 50 Hz e reactance/phase of the primary winding ar ding values for the secondary winding are C primary winding is connected in delta and
6. What is the effect of load inductance on the ripple current? 7. i effect of chonnine Bock and boost 8. Wh 9 What chopping 10. At what duty evcle does the load current rinnle current he
What is phase angle of voltage induced in primary and secondary windings of transformers due to mutual flux? Same Opposite Zero None of option
Three single phase transformers are connected in a Delta-Wye configuration. Each transformer is rated 13kV/64kV. The transformers are connected to a 3 phase 13kV (L-L) supply and the balanced three phase load is 788KVA. What is the current magnitude in the secondary winding of each transformer? explain the steps too please
A generator supplies a motor through a Y-A transformer. The generator is connected to Y side of the transformer. A fault occurs between the motor terminals and the transformer. The symmetrical components of the subtransient current in the motor flowing toward the fault are: I =-0.8- j2.6pu I =-j2.0pu I =-j3pu From the transformer toward the Fault: I = 0.8– j0.4pu I? =-j1.0pu 1 = Opu Assume X =X,=X, for both the motor and the generator. (a) Describe the fault type and find the prefault current, if any, in line a. (b) Determine the subtransient fault current in per unit. (c) Calculate the subtransient current in each phase of the generator in per unit taking into consideration the phase shift of the Y-A transformer.
In no load phasor diagram of practical transformer, the magnetizing current Imag is with flux Ø O Leading by 30° O Lagging by 60° In phase O 90° out of phase
The regulation of an alternator is likely to be negative in case of resistive load O True O False