Write the direct stress formula in its three forms and explain the meaning of each one.
To write: Direct stress formula in three forms and explain the meaning of each one.
Explanation of Solution
The three forms direct stress formula are as follows:
1.
Here,
It means the average normal stress in a member is equal to axial normal force acting on it divided by the area of cross-section on which the normal force acts. It is used to calculate the average stress developed in a member having a cross- sectional area A, when an external force of magnitude P act.
2.
Where,
P is the axial load capacity.
A is the cross-sectional area of the member.
This form of the formula is used to calculate the maximum load capacity (maximum permissible axial load) of a member having maximum permissible stress,
3.
Where,
P is the axial load capacity.
A is the cross-sectional area of the member.
This formula is applicable for Analysis of load capacity.
Want to see more full solutions like this?
Chapter 9 Solutions
Applied Statics and Strength of Materials (6th Edition)
Additional Engineering Textbook Solutions
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
Manufacturing Engineering & Technology
Mechanics of Materials (10th Edition)
Engineering Mechanics: Statics
Engineering Mechanics: Statics & Dynamics (14th Edition)
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
- The state of stress at a point in a member is shown on the element. Suppose that o = -40 MPa , oy = -120 MРа, три — -28 MPа . Part A Determine the normal stress component acting on the plane AB. (Figure 1) Express your answer with the appropriate units. HA ? Figure 1 of 1 Value Units Submit Request Answer Part B Determine the shear stress component acting on the plane A.B. 30% Express your answer with the appropriate units. y = | Value В Units Pearsonarrow_forwardA force F of 40000 lbf is applied to rod AC the negative Y-direction. The rod is 1000 inches tall. A Force P of 25 lbf is applied in the negative Z- direction at point E, and a force R of 75 lbf is applied in the negative Z-direction at point F. Rod AC has a diameter of 1 inch from A to C, a diameter of 1.5 inches from B to C, and all fillet radii are 0.25 in. The rod is made of 1020 CD steel, and has a Sy of 135 ksi, a Sut of 150 ksi, and an ɛf = 0.15. Y A 100 100 200 800 B. „D D. 100 2D view of rod AC in XY planearrow_forwardPlease answer as per question and in clear handwriting. The state of stress at a point in a structure is shown in the following figure.Decide:(a) The forces acting on an element oriented at an angle in the directioncounterclockwise θ = 15° from the x-axis (Show the results in a sketch ofcorrectly oriented)(b) find the main stresses (Show the results on a sketch ofcorrectly oriented)arrow_forward
- The state of stress at a point in a member is shown on the element. Suppose that o = -50 MPa , oy = -120 MPa , Try = -30 MPa Part A Determine the normal stress component acting on the plane AB. (Figure 1) Express your answer with the appropriate units. HA Value Units Submit Request Answer Figure 1 of 1 Part B A Determine the shear stress component acting on the plane AB. Express your answer with the appropriate units. 30% HA ? Tz'y = Value Units Submit Request Answer Barrow_forwardFind the values of σs and σ22 for the state of the stress shown in Figure 3arrow_forwardShows the state of stress (three dimensional) at a point Q within a given stressed body. b- Briefly describe the three normal stress components and the six shear stress components of the stress at point Q. c- Consider a tetrahedron containing point Q and show the forces on the faces of the tetrahedron due to the various stresses. d- How can we derive the equation for the transformation of normal stress by considering the above mentioned tetrahedron?arrow_forward
- Can you calculate the stress for the remaining point instead of point 1 only?arrow_forwardDetermine the resulting maximum value of the normal stress. Specify the orientation of the plane on which these maximum values occur. **The answer is tensile stress is 0 ksi at 90 degrees. **The answer is compressive stress is 7 ksi at 0 degrees. Can you explain how that is? This was my thought process: I know that tensile would be zero because the force P is actually going inwards and not outwards. I know that means that there would be a compressive force. I am confused on the angles, how is a tensile force going 90 degress if there technically is no force in the tensile direction. And how is there a compressive force at 90 degrees if there is a stress? thank you!arrow_forwardHow is the state of plane stress at the point uniquely represented?arrow_forward
- a-Shows the state of stress (three dimensional) at a point Q within a given stressed body. b- Briefly describe the three normal stress components and the six shear stress components of the stress at point Q.arrow_forward200 mm 400 mm 20 mm J A Section a - a F₁ F₂ 4arrow_forwardA member is subjected to a major stress of 115 MPa (tensile), minor stress of 50 MPa (tensile) along with a counter clockwise shear stress of 20 MPa. Calculate the Normal stress, tangential stress, Resultant stress and its inclination on plane make 35° to major stress. Validate your analytical results by drawing Mohr's circle. marks, Mohr's circle - (ENTER ONLY THE VALUES IN THE BOXES BY REFERRING THE UNIT GIVEN IN BRACKET & UPLOAD YOUR HAND WRITTEN ANSWERS IN THE LINK PROVIDED) (i) Normal Stress (unit is MPa) = (ii) Tangential Stress (unit is MPa) (iii) Resultant Stress (unit is MPa) (iv) Resultant inclination (unit in degree) = %3Darrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY