![Control Systems Engineering](https://www.bartleby.com/isbn_cover_images/9781118170519/9781118170519_largeCoverImage.gif)
Concept explainers
Figure Pl.5 shows the topology of a photo-voltaic (PV) system that uses solar cells to supply electrical power to a residence with hybrid electnc vehicle toads (Gurkavnak. 2009). The system consists of a PV array to collect the sun's rays, a battery pack to store energy during the day. a dc/ac inverter to supply ac power to the load, and a bidirectional dc/dc converter to control the terminal voltage of the solar array according to a maxunum power point tracking (MPPT) algorithm. In case of sufficient solar power (solar insolation), the dc/dc converter charges die battery and die solar array supplies power to the load through the dc/ac inverter. Widi less or no solar energy (solar non-insolation). power is supplied from the battery to the load through the dc/dc converter and die dc/ac inverter. Thus, the dc/dc converter must be bidirectional to be able to charge and discharge the batlery. With the MPPT controller providing the reference voltage, the converter operates as a step-up converter (boost) to discharge the battery if the battery is full or a step-down (buck) converter, which charges die batlery if it is not full.7
In Figure Pl.5, the Inverter is controlled by die Power Manager and Controller through the Current Controller. The Power Manager and Controller directs the Inverter to take power either from the battery, via the Bidirectional Converter, or the solar array.
of charge (SOC). Draw the follow ing two functional block diagrams for this system:
- A diagram that illustrates the conversion of solar irradiation into energy stored in the battery. In that diagram, the input is the solar irradiance. r(t), and the output is the battery voltage. Vb(t).
- The main diagram, in w hich the input is the desired output voltage. Vr(t) and the output is the actual inverter output voltage, Vo(t) Both of these functional block diagrams should show their major components, including the PV array, MPPT controller, dc/dc converter, battery pack, dc/ac inverter, current controller, and the Power Manager and Controller. Show all signals, including intermediate voltages and currents, time of day. and the SOC of the battery.
![Check Mark](/static/check-mark.png)
Want to see the full answer?
Check out a sample textbook solution![Blurred answer](/static/blurred-answer.jpg)
Chapter 1 Solutions
Control Systems Engineering
- 1. A motor coil can be modeled as a hollow copper cylinder with an outer diameter of 0 50 mm, an inner diameter of 40 mm, and a length of 60 mm. The motor stalls at time t = 0 and, at this point, the copper experiences a step input in electrical heating of Po u(t), where Po is 350 W. Assume that there is little time for significant heat loss to the environment so that the copper cylinder can be considered to be insulated. If the initial temperature is 30 °C, find the temperature as a function of time, T(t), analytically using Laplace transforms. Calculate the time required to reach the breakdown temperature of the wire insulation, which is approximately 250 °C. Write a script file in MATLAB® to: (a) determine the time for the copper to reach 250 °C using the command find; and (b) plot T(t) over this time interval. Copper has a density of 8960 kg/m³ and a specific heat of 390 J/kg-°C. 25 mm 20 mm P(t) = Pou(t)arrow_forwardDescribe finite element modeling?arrow_forwardElectrical discharge machining process, breakdown voltage across inter electrode gap (IEG) IS 300 V and the capacitance of the RC circuit is 50. The energy released per across IEG is?arrow_forward
- Help! Please show complete and explicit solution with step by step explanation thankyou! Calculate the total heat transfer for 12 hours through an insulated window (two glass panes with an air gap of 1/4 in) that measures 4 ft × 7 ft, when the outside temperature is 5°F and the inside temperature is 65°F.arrow_forwardA stand-alone photo voltaic (PV) system for operating a street light consists of a PV array, storage battery, controller and DC-AC inverter o which an LED bulb of 20 Watts is connected. The PV array consists of 2 modules each containing 36 single crystal Si cells, each of 10 cm diameter. Conversion efficiency of the PV cells is 11%. The battery has an efficiency of 0.82 both while charging and discharging. DC-AC inverter has an efficiency of 0.85 while discharging the energy. The PV array receives solar radiation of approximately 22,600 kJ/m? per day. i. If the controller switches on the street light at 18:00 hrs, find the time when the street light would be switched off because of complete battery discharge. Calculate the energy stored in the battery on this day. ii.arrow_forwardAn aircraft wing is modelled by using a specific element type, which is defined by 2 nodes as shown below. Each node of this element has 3 Degrees of Freedom. If the total number of nodes, used for modelling the wing, is equal to 3,760 then calculate the total degree of freedom of the system. Node 1 Your Answer: element Node 2arrow_forward
- I need right solution with clear calculations. A workplace is occupied by 100 people who are averaging 250 Watts/person. The space is measured as 30 meters x 20 meters x 15 meters (L x W x H). What is the internal heat gain of this space given off by a full staff? If you need to provide the workplace 10 air changes per hour, what type of infiltration inflow rate need to be (cubic meters/hour)?arrow_forwardHeat Transfer Design a 1D conduction experiment to measure thermal conductivity of 3 different materials that can be done in your kitchen. Identify the variables that will be changed and write a detailed protocol.arrow_forwardGeochemical Box Models - please use same terminology found in question Consider an element X exchanging between two geochemical reservoirs A and B. Let MA and MB be the masses of X in reservoirs A and B, respectively; let tA and tB be the residence times of X in reservoirs A and B, respectively. Further let M = MA + MB be the total mass of X in the two reservoirs combined. Consider a situation where additional mass M' is injected into reservoir A at time t=0 increasing the total amount of element X in the system from M0 to M1, with no further injection at later times; further assume that tA >> tB, that the total mass in the altered system is M1 = M0 + M', and that M0 << M'. Give an expression for MB(t) as a function of M1, tA, tB, and t. What is the characteristic time for MB to approach steady state? What is the characteristic time for MA to approach steady state?arrow_forward
- In an electrical discharge machining process, the breakdown voltage across inter electrode gap (IEG) is 200 V and the capacitance of the RC circuit is 50 μF. The energy (in J) released per spark across the IEG is Tarrow_forwardYou are testing a long-dwelling catheter for its biological response using a rat model. After implantation for 4 months you explant the catheter material and surrounding tissue. Histology shows the catheter material surrounded by a thin layer of aligned collagen that is, in turn, surrounded by numerous polymorphonuclear cells. What has occurred? Describe the short term and long term events that led to this outcome. Note: the fact that this is a rat model rather than a human is not the issue - the model is fine.arrow_forwardActivity 3: The network and communication systems attached to the smart grid, including the routers and computing units, contain stages where signals are expressed in different bases. Your task is to compute the output of some of these operations by showing a detailed solution for each operation. 1. Compute 1100102 x 10102. 2. Compute 1100102 + 10102. 3. Compute 7758 × 7458. 4. Compute 7758 + 754g. 5. Compute CF1216 x F1316. 6. Compute CF1215 + F1316. 7. Compute 7758 × F1315+ 10102 8. Compute 1378 x 1100102x AC316arrow_forward
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
![Text book image](https://www.bartleby.com/isbn_cover_images/9781305387102/9781305387102_smallCoverImage.gif)