ELECTRICITY FOR TRADES (LOOSELEAF)
3rd Edition
ISBN: 9781260437454
Author: Petruzella
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 8.2, Problem 1RQ
Calculate the total resistance for each of the following resistor circuits:
- a. Series circuit: R1 = 40 Ω, R2 = 75 Ω
- b. Parallel circuit: R1 = 200 Ω, R2 = 200 Ω, R3 = 200 Ω
- c. Series circuit: R1 = 2,000 Ω, R2 = 6,000 Ω, R3 = 2,200 Ω
- d. Parallel circuit: R1 = 14 Ω, R2 = 32 Ω
- e. Series circuit: R1 = 4,700 Ω, R2 = 800 Ω, R3 = 200 Ω
- f. Parallel circuit: R1 = 60 Ω, R2 = 30 Ω, R3 = 15 Ω
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
In circuit below
a. What is the total resistance of branch 1?
b. What is the resistance of branch 2?
c. How much are the branch currents I1 and I2?
d. How much is the total current, I T, in the circuit?
e. How much is the total resistance, RT, of the entire circuit?
f. What are the values of V1, V2, and V3?
V is the same as E (VOLTAGE)
For the circuit illustrated in figure 3, perform the calculation of the total equivalent resistance and the total current.given: R1 = 1.0 kΩ R2 = 1.0 kΩ R3 = 1.0 kΩ R4 = 3.0 kΩ R5 = 1.0 kΩ R6 = 1.0 kΩ
Draw the below given circuit. Change value of components according to your circuit. Use ammeter, voltmeter and ohmmeter to measure the current, voltage and resistence. Use Norton's theorem to find the current flowing through R 2 resistor shown in figure. R1=35 N, R2=50 N, R3=30 N, R4=20 Q, R=10 N and V=70 volts.
Chapter 8 Solutions
ELECTRICITY FOR TRADES (LOOSELEAF)
Ch. 8.1 - In what way is resistance wire different from the...Ch. 8.1 - What is the trade name for the most popular type...Ch. 8.1 - Prob. 3RQCh. 8.1 - Name the three ways by which resistors are rated.Ch. 8.1 - Resistors are classified as passive devices. Why?Ch. 8.1 - Identify the type of circuit that generally...Ch. 8.1 - State two functions served by a fusible resistor.Ch. 8.1 - What advantage do film resistors have over...Ch. 8.1 - What are the two configurations for chip...Ch. 8.1 - In what way is the construction of an adjustable...
Ch. 8.1 - Compare the connection and control function of a...Ch. 8.1 - If the wiper arm of a linear potentiometer is...Ch. 8.1 - Explain how a 10-turn trim pot is adjusted.Ch. 8.1 - Compare the way the resistance varies in a linear...Ch. 8.1 - Identify the color bands for each of the following...Ch. 8.1 - A 680- resistor has a rated tolerance of 10...Ch. 8.1 - What is the color code for a 365- five-band...Ch. 8.1 - Determine the resistance value and percentage of...Ch. 8.1 - Determine the resistance value and percentage of...Ch. 8.2 - Calculate the total resistance for each of the...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Step 3:Calculate (Theoreticallyand LTspice) the Thevenin equivalent resistance between points a and b (RTh(a,b)) [Ω] and between points b and c (RTh(b,c)) [Ω]. Use the circuit diagram of figure 2 Step 4:Calculate (Theoretically and LTspice) the Thevenin equivalent voltagesbetweenpoints a and b(VTh(a,b)) [mV] and betweenpoints b and c(VTh(b,c)) [mV]. Use the circuit diagram of figure 1.Keep Switch 1 and Switch 2 open Step 5: Calculate (Theoretically and LTspice) thevoltageacross resistor R5(VR5) [mV]andthe voltage across resistor R6 (VR6) [mV]. Use the resistance values from step 3as follow R5= RTh(a,b)and R6= RTh(b,c).For the calculation of VR5close Switch 1 and leave Switch 2 open. For the calculation of VR6 close Switch 2 and leave Switch 1 open. Use the circuit diagram of figure 1. Step 6:Calculate (Theoretically and LTspice) themaximumpower absorbed by resistor R5(PR5) [μW]andthe maximumpower absorbed by resistor R6(PR6) [μW]. Use the resistance values from step 3as follow R5=…arrow_forward5. a. How is the current in resistor R1 affected as resistors R2 and R3 are added in parallel? Give your reasoning and answer in 1-3 well written sentences. b. How is the effective resistance of the circuit branch containing R1 affected as additional resistors are added to the circuit in parallel? Give your reasoning and answer in 2-3 well written sentences C. How is the total current in a circuit affected as resistors are added in parallel? Give your answer and reasoning in 2-3 well written sentences.arrow_forwardFor the network in Figure 3 below, (a) Evaluate the value of the equivalent resistance, R for the whole circuit (b) Sketch and label a simplified circuit containing only 1 voltage source and 1 resistor. (c) Assess Is, I1, I3 and I4. (c) Calculate Vab.arrow_forward
- a. For the circuit shown in Figure 4, calculate the Thevenin voltage, VTh, with respect to the terminals A and B, where RL is the load resistor. b. For the circuit shown in Figure 4, calculate the Thevenin resistance, RTh, with respect to the terminals A and B. c. For the circuit shown in Figure 4, what is the maximum amount of power that can be transferred to the load resistor RL?arrow_forwardPROCEDURE: Perform the steps indicated below for the circuit(s) of Figures 2 & 3. Step 1. For the original circuit calculate the following: a. The current through the load resistor (IL); b. The voltage across the load resistor (VL); c. I short circuit (ISC); d. V open circuit (VOC). This is the Thevenin voltage (ETH); e. The resistance (RTh)between the terminals A and B with the power supplies replaced by their internal resistances. Step 2. Using the values obtained in Part 1 for ETH and RTH, draw the complete Thevenin equivalent circuits including all necessary details on the schematic. Step 3. Construct the original circuits and measure the following: a. All the resistor values being used. b. The current through the load resistor (IL); c. The voltage across the load resistor (VL); d. The current through RLwhen RL = 0W (ISC); e. The voltage from A to B with RLequal…arrow_forwardFor the circuit shown below with the 12V DC supply: Calculate the total resistance RT. Show all your work in details. Calculate the total current Is. Calculate VR1 and VR2 in the circuit. Calculate the total power dissipated in the circuit. Calculate the power dissipated by R1 and R2.arrow_forward
- 1. VDC = 10 V, R1 = 3.5 kΩ, R2 = 7.0 kΩ and R4 has resistance range between1.0 kΩ to 10.0 kΩ, calculate the range of unknown resistor can be measuredby the bridge. 2. Discuss what will occur if the Wheatstone bridge is in unbalance condition.arrow_forwardA. Find the Thévenin equivalent resistance with respect to the terminals a, b in the circuit in(Figure 1, the figure with the caption) without finding either the open-circuit voltage or the short-circuit current. B. Find the Norton equivalent resistance with respect to the terminals a, b in the circuit in(Figure 2) without finding either the open-circuit voltage or the short-circuit current.arrow_forwardUsing the circuit in the image and the figures in the attached table: a. With both switches, SW1 and SW2 left open complete the following: i. Briefly discuss what the three resistors are used for. ii. Determine the total resistance in the circuit. iii. Determine the currents flowing in the circuit. iv. Determine the volt drops around the circuit. v. Use the appropriate Kirchhoff’s law to confirm your results. b. Now close switch SW1 and complete the following: i. Determine the total resistance in the circuit. ii. Determine the currents flowing in the circuit. iii. Determine the volt drops around the circuit. iv. Use the appropriate Kirchhoff’s law to confirm your results. c. Now Whilst keeping SW1 closed close SW2 and complete the following: i. Determine the total resistance in the circuit. ii. Determine the currents flowing in the circuit. iii. Determine the volt drops around the circuit. iv. Use the appropriate Kirchhoff’s law to confirm your results.arrow_forward
- Step 5: Calculate the voltage across resistor R6 (VR6) [mV]. Use the resistance values from step 3 as follow R5 = 211.51ohm andR6 = 1420.86ohm. For the calculation of VR5 close Switch 1 and leave Switch 2 open. For the calculation of VR6 close Switch 2 and leave Switch 1 open. Use the circuit diagram of figure 1. Step 6: Calculate the maximum power absorbed by resistor R5 (PR5)[μW] and the maximum power absorbed by resistor R6 (PR6) [μW]. Use the resistance values from step 3 as follow R5= RTh(a,b) and R6 = RTh(b,c). Vs = 1.5V R1 = 4700ohm R2 = 2200ohm R3 = 6800ohm R4 = 2700ohm VR2 = 0.253V VR4 = 0.311V VR5 = 254mVarrow_forward" SUPERPOSITION THEOREM " Please Find the Current and Voltages in 6k , 3k , 6k Ohm Resistors only, with a total of 3 currents and 3 voltages to compute Using SUPERPOSITION THEOREM thankyou very much ! I've included a cicruit app to check if your answer was correct and close to the value of currents and voltages thankyou! I've been testing simple circuits to practice problems using different theorems,I appreciate you very much Thankyou!arrow_forwardPart B Given the following circuit: Calculate the current through each Resistance R1 to R6 when its correspondent switch is closed (e.g. the current through R1 when the switch SW1 is closed, the current through R2 when the switch SW2 is closed, etc.) If the value of the Fuse F1 is 1 Amperes, which different combinations of switches can you close together to ensure that will be the maximum current possible but the Fuse F1 will not blow apart? – Justify your answer with your calculations. If the value of the Fuse F1 is 2 Amperes, which different combinations of switches can you close together to ensure that will be the maximum current possible but the Fuse F1 will not blow apart? – Justify your answer with your calculations. If the value of the Fuse F1 is 3 Amperes, which different combinations of switches can you close together to ensure that will be the maximum current possible but the Fuse F1 will not blow apart? – Justify your answer with your calculations Calculate the minimum…arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- EBK ELECTRICAL WIRING RESIDENTIALElectrical EngineeringISBN:9781337516549Author:SimmonsPublisher:CENGAGE LEARNING - CONSIGNMENT
EBK ELECTRICAL WIRING RESIDENTIAL
Electrical Engineering
ISBN:9781337516549
Author:Simmons
Publisher:CENGAGE LEARNING - CONSIGNMENT
Electrical Measuring Instruments - Testing Equipment Electrical - Types of Electrical Meters; Author: Learning Engineering;https://www.youtube.com/watch?v=gkeJzRrwe5k;License: Standard YouTube License, CC-BY
01 - Instantaneous Power in AC Circuit Analysis (Electrical Engineering); Author: Math and Science;https://www.youtube.com/watch?v=If25y4Nhvw4;License: Standard YouTube License, CC-BY