What is translating coordinate system?

Q: : the wo om 329K

A: GIVEN:T1=320kT2=500K

Q: Describe How to mesh irregular volume by using ANSYS?

A: To mesh a volume with all hexahedron elements, the following conditions must be satisfied; 1.The…

Q: draw isometric view of the given three views

A:

Q: Position and Disnlacanant Analveis

A:

Q: orthographic view (software drawn)

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Briefly describe what is meant by a right handed system of coordinate

A: System of cordinates -  A cordinate system is defined as a system which is used to define the…

Q: What are all the distances between datum target points, B1 and B2 ? Y = Z =

A: Solution:

Q: at direction should you paddle te

A: 21.80 Degree ( from downstream)

Q: provide Orthographic view

A: Question fig.

Q: QUESTION 4 Moving by 1 inch in the X-direction, from an X-Y coordinate location of (3.5, 2) to (4.5,…

A: Types of positioning movement - (i) Absolute positioning movement (ii) Incremental positioning…

Q: the following is not one of the nonmachine tool applications of numerical control.   Question 24…

A: None of the above is the correct answer

Q: The acronym PASS' is used to explain the method of using fire extinguishers. In this, 'A' stands for…

A: The acronym PASS, which stands for Pull, Aim, Squeeze, and Sweep.

Q: Differentiate between NC and CNC system and the applications of CNC. b) What are G-codes and M-codes…

A:

Q: What is the acceleration of block A?

A:

Q: Which of the twelve geometric controls is the most common? O Angularity O Position O Flatness O…

A: A feature control frame is used in GD&T to show the condition and tolerance provided in the…

Q: Define translating coordinate system.

A: Coordinate systems are those systems which are used to specify the location of any point in space.…

Q: 15

A: The orthographic view of the given isometric drawing is drawn and shared below.

Q: Draw the top and front view of the figure 2 using AutoCad

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Consider FIG-DD in the appendix.   Note: For Blocks “A” & “B” & “C”: The mass of “A” is 30 kg.…

A:

Q: Which of the following sets of measurements can be used to calculate acceleration? *

A:

Q: Draw the top, the front, and the right-side orthographic views of the objects shown. Indicate when…

A: TOP VIEW

Q: Orthographic projection of the component show below

A:

Q: Define the speed of point C.

A: The given system is rack and pinion arrangement. The tangential velocity at A is given as 2 ft/s and…

Q: Which of the following settings does not allow you to control point specifications?a. Grid b. Snap…

A: From the given options, the snap, ortho and the polar settings are used to specify a point. Hence…

Q: the angular velocity

A:

Q: Evaluate:∫ds

A: From question   ∫ds = S + c Where c is Intregated constant.

Q: i need the answer quickly

A: home > line > 0,0> enter >keep mouse in right > type 25>  enter> up >type 10…

Q: Write all the commands steps of the AutoCAD software to reach the drawing of the figure below all…

A:

Q: a-) What is konck? Describe the Knock mechanism formed in the cylinder by drawing a figure. What is…

A: Knocking is the phenomena commonly occurring in a CI engine. You may know that in a CI engine the…

Q: The other degree of rotation from the start point that will result in Erika being the same distance…

A:

Q: Draw an isometric view of the following Dovetail Slide.

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: what is its position when t 11 s?

A: Solution : Given data :  a2t -6 m/s2

Q: Calculate two blocks acceleration

A: For solution refer below images.

Q: Create the front view of the sketch of the spur wheel (hand written asap))

A: Spur gear is used to transmit power and motion from one shaft to another. it will either increase or…

Q: 1. What is your mech diameter of 3

A: given:l=35cmr=3/2cm

Q: The front and top views of an object are shown below. Freehand sketch the full auxiliary view and ce…

A: The given views are  Front and top view  To sketch auxiliary view

Q: Need you to draw orthographic views of this object.

A: The required orthographic views are drawn using third angle method of projection.

Q: Which of the ff is the best way of dimensioning?

A: Solution: To find: Best way of Dimensioning.

Q: d. 1. What are the four types of moves and describe how they move between waypoints. a. b. C.

A: Given Robotic motion To find Types of motion

Q: ☆Draw figures 1 and 2 using AutoCAD and store the drawings in red at the command of Block

A:

Q: Transmission angle is the angle between which two links of a slider crank mechanism? O Connecting…

A:

Q: Velocity of Point B Velocity of Point C The angular velocity of Link 4 e sure you submit all…

A:

Q: 4- Which of the following lines is used to: show the axis of symmetry for feature part, indicate and…

A: Which of the following lines is used to: show the axis of symmetry for a feature or part, indicate a…

Q: What is the shortcut key for "Find and ?Replace" dialog box + Ctrl + Shift + FO Ctrl + RO Ctrl + FO…

A: Correct answer: Ctrl + H

Q: Match List-I (NC Code) with List-II (Definition) and select the correct answer using the codes given…

A:

Q: LS HELP ME IDENTIFY THE OBLIQUE, TOP, RIGHT, AND FRONT VIEW THANK YOU!!

A:

Q: ey-coordinate

A: 9.395

Q: Draw clearly the Kinematic diagram and the degree of freedom Child's digging toy

A:

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.