Fluid Mechanics Fundamentals And Applications
3rd Edition
ISBN: 9780073380322
Author: Yunus Cengel, John Cimbala
Publisher: MCGRAW-HILL HIGHER EDUCATION
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 6, Problem 96P
To determine
The force acting in the axial direction.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A stream with Q = 8 m3/s Flow rate is passed through the turbine by means of a pressure pipe. its velocity at the entrance of the pipe V1 = 4 m/s, the exit velocity from the pipe at the point where it is released back into the stream after the turbine is V2= 1 m/s. The height of drop between the inlet and outlet of the pipe is 80 m and the energy converted to heat is 10 m inside the pressure pipe , determine the energy transferred to the turbine and the theoretical strength of turbine.
60 degree F water flows through a horizontal turbine. The water speeds at the turbine inlet and the turbine outlet are identical. The water gage pressure at the turbine inlet is 46.4 psi while that at the outlet is 12.2 psi. Assume water frictional losses through the turbine are negligible.
Deterimine the shaft work rate in ft*lb per slug of water passing through the turbine. Answer
with a positive number if mechanical energy goes into the water and
a negative number if mechanical energy comes out of the water
as it passes through the turbine.
Water is flowing through a U-section pipe as shown in Figure 1.2.
At flange (1) the total absolute pressure is 240 kPa, and water flows into the pipe at 42 kg/s.
At flange (2), the total pressure measured is 190 kPa with a flow rate of32 kg/s.
At point (3) water discharges into the atmosphere at 90 kPa at a flowrate of 10 kg/s.
The mass of the elbow and the water in it is 50 kg.
Neglecting the momentum-flux correction factor, determine the net x- and z-force at the two flanges connecting the pipe.
Chapter 6 Solutions
Fluid Mechanics Fundamentals And Applications
Ch. 6 - Express Newton’s first, second, and third laws.Ch. 6 - Express Newton’s second law of motion for rotating...Ch. 6 - Is momentum a vector? If so, in what direction...Ch. 6 - Express the conservation of momentum principle....Ch. 6 - Two firefighters are fighting a fire with...Ch. 6 - How do surface forces arise in the momentum...Ch. 6 - Explain the importance of the Reynolds transport...Ch. 6 - What is the importance of the momentum-flux...Ch. 6 - Write the momentum equation for steady...Ch. 6 - In the application of the momentum equation,...
Ch. 6 - A rocket in space (no friction or resistance to...Ch. 6 - Describe in terms of momentum and airflow how a...Ch. 6 - Does it take more, equal, or less power for a...Ch. 6 - In a given location, would a helicopter require...Ch. 6 - A horizontal water jet from a nozzle of constant...Ch. 6 - Describe body forces and surface forces, and...Ch. 6 - A constant-velocity horizontal water jet from a...Ch. 6 - A horizontal water jet of constant velocity V from...Ch. 6 - Water enters a 10-cm-diameter pipe steadily with a...Ch. 6 - A 2.5-cm-diameter horizontal water jet with a...Ch. 6 - A horizontal water jet of constant velocity V...Ch. 6 - A 90 elbow in a horizontal pipe is used to direct...Ch. 6 - Repeat Prob. 6-20 for the case of another...Ch. 6 - A horizontal water jet impinges against a vertical...Ch. 6 - A reducing elbow in a horizontal pipe is used to...Ch. 6 - Repeat Prob. 6-24 for the case of = 125°.Ch. 6 - Reconsider Prob. 627. If the mass of the cart is...Ch. 6 - A 100-ft3/s water jet is moving in the positive...Ch. 6 - Reconsider Prob. 6-26E. Using appropriate...Ch. 6 - A horizontal 5-cm-diameter water jet with a...Ch. 6 - A fan with 24-in-diameter blades moves 2000 cfm...Ch. 6 - A 3-in-diameter horizontal jet of water, with...Ch. 6 - Firefighters are holding a nozzle at the end of a...Ch. 6 - A 5-cm-diameter horizontal jet of water with a...Ch. 6 - A 3-in-diameter horizontal water jet having a...Ch. 6 - An unloaded helicopter of mass 12,000 kg hovers at...Ch. 6 - Water is flowing through a 10-cm-diameter water...Ch. 6 - The weight of a water tank open to the atmosphere...Ch. 6 - Commercially available large wind turbines have...Ch. 6 - Water enters a centrifugal pump axially at...Ch. 6 - An incompressible fluid of density and viscosity ...Ch. 6 - Consider the curved duct of Prob. 6-41, except...Ch. 6 - As a follow-up to Prob. 6-41, it turns out that...Ch. 6 - An incompressible fluid of density and viscosity ...Ch. 6 - Water of density =998.2kg/m3 flows through a...Ch. 6 - Water flowing in a horizontal 25-cm-diameter pipe...Ch. 6 - A sluice gate, which controls flow rate in a...Ch. 6 - How is the angular momentum equation obtained from...Ch. 6 - Prob. 52CPCh. 6 - Prob. 53CPCh. 6 - Prob. 54CPCh. 6 - Water is flowing through a 15-cm-diameter pipe...Ch. 6 - A large lawn sprinkler with two identical arms is...Ch. 6 - Prob. 57EPCh. 6 - Prob. 58PCh. 6 - The impeller of a centrifugal blower has a radius...Ch. 6 - Prob. 60PCh. 6 - Repeat Prob. 6-56 for a water flow rate of 60 L/s.Ch. 6 - Prob. 62PCh. 6 - Water enters the impeller of a centrifugal pump...Ch. 6 - A lawn sprinkler with three identical antis is...Ch. 6 - Prob. 66PCh. 6 - Water flowing steadily at a rate of 0.16 m3/s is...Ch. 6 - Repeat Prob. 6-66 by taking into consideration the...Ch. 6 - Prob. 70PCh. 6 - Water enters vertically and steadily at a rate of...Ch. 6 - Repeal Prob. 6-69 for the case of unequal anus-the...Ch. 6 - Prob. 73PCh. 6 - Prob. 74PCh. 6 - Prob. 75PCh. 6 - Prob. 76PCh. 6 - A spacecraft cruising in space at a constant...Ch. 6 - A 60-kg ice skater is standing on ice with ice...Ch. 6 - Prob. 80PCh. 6 - Water is flowing into and discharging from a pipe...Ch. 6 - Indiana Jones needs So ascend a 10-m-high...Ch. 6 - Prob. 83EPCh. 6 - Prob. 84PCh. 6 - A walnut with a mass of 50 g requires a force of...Ch. 6 - Prob. 86PCh. 6 - Prob. 87PCh. 6 - Show that the force exerted by a liquid jet on a...Ch. 6 - Prob. 89PCh. 6 - Prob. 90PCh. 6 - Prob. 91PCh. 6 - Water enters a two-armed lawn sprinkler along the...Ch. 6 - Prob. 94PCh. 6 - Prob. 95PCh. 6 - Prob. 96PCh. 6 - Water flows steadily through a splitter as shown...Ch. 6 - Prob. 98PCh. 6 - Prob. 99PCh. 6 - Consider water flow through a horizontal, short...Ch. 6 - Consider water flow through a horizontal. short...Ch. 6 - Prob. 103PCh. 6 - Prob. 104PCh. 6 - Prob. 105PCh. 6 - Prob. 106PCh. 6 - The velocity of wind at a wind turbine is measured...Ch. 6 - The ve1ocity of wind at a wind turbine is measured...Ch. 6 - Prob. 109PCh. 6 - Prob. 110PCh. 6 - Prob. 111PCh. 6 - Prob. 112PCh. 6 - Consider the impeller of a centrifugal pump with a...Ch. 6 - Prob. 114P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- PROBLEM 1 A stream of water (p = 1000 kg/m³) enters a steady- state flow diverter shown in the figure. The water enters the device at 4 m/s at Point 1, which has a cross-sectional area of 250 cm² and an absolute pressure of P₁. The mass flow splits evenly between the exits at Point 2 and Point 3, and the speed of the fluid remains constant at 4 m/s. Points 2 and 3 are at Patm. The flow diverter is constrained by a pinned (frictionless) joint at Point A and a (frictionless) roller at Point B. The mass of the diverter including the water is 60 kg. The location of the center of mass CG and other pertinent dimensions are shown on the figure. Determine the reactions at Point A and Point B. 50° CG 3 d 2 a = 0.5 m b = 1.0 m c = 0.4 m d = 0.2 m SETUP BUT DO NOT SOLVE. Clearly identify the unknowns and the final equations. Your answer should consist of a minimum and sufficient set of equations that could provide the answers. a aarrow_forwardA hydraulic nozzle is fed from a 0.19 m diameter pipe with an inlet pressure of 581 kPa and a velocity of 6.43 m/s as shown in the figure below. There is a 0.01 m diameter jet that discharges into an environment where the pressure is 54 kPa. Find the axial force generated at the joint A. D2 D1 A →トarrow_forwardWater enters a centrifugal pump axially at atmospheric pressure at a rate of 0.10 m3/s and at a velocity of 6 m/s and leaves in the normal direction along the pump casing, as shown in the figure. Determine the force acting on the shaft (which is also the force acting on the bearing of the shaft) in the axial directionarrow_forward
- Water is flowing through a U-section pipe as shown in Figure 1.2. At flange (1) the total absolute pressure is 240 kPa, and water flows into the pipe at 42 kg/s. At flange (2), the total pressure measured is 190 kPa with a flow rate of 32 kg/s. At point (3) water discharges into the atmosphere at 90 kPa at a flow rate of 10 kg/s. The mass of the elbow and the water in it is 50 kg. Neglecting the momentum-flux correction factor, determine the net x- and z-force at the two flanges connecting the pipe. T0 kg/s 3 ст 32 kg/s- 10 cm 42 kg/s S cm Figure 1.2arrow_forwardA power plant requires 940 L/min of water. The required net head is 5 m at this flow rate. An examination of pump performance curves indicates that two centrifugal pumps with different impeller diameters can deliver this flow rate. The pump with an impeller diameter of 203 mm has a pump efficiency of 73 percent and delivers 10 m of net head. The pump with an impeller diameter of 111 mm has a lower pump efficiency of 67 percent and delivers 5 m of net head. What is the ratio of the required brake horse power (bhp) of the pump with 203-mm-diameter impeller to that of the pump with 111-mm-diameter impeller? (a) 0.45 (b) 0.68 (c) 0.86 (d) 1.84 (e) 2.11arrow_forwardA jet of water having a velocity of 30 m/s strikes a series of radial curved vanes mounted on a wheel which is rotating at 300 rpm. The jet makes an angle of 30 ∘ with the tangent to the wheel at inlet and leaves the wheel with a velocity of 4 m/s at an angle of 120 ∘ to the tangent to the wheel at outlet. Water is flowing from outward in a radial direction. The outer and inner radii of the wheel are 0.6 m and 0.3 m respectively. Determine: (a) Vane angles at inlet and outlet , (b) Work done per second per kg of water, and (c) Efficiency of the wheel.arrow_forward
- 4. Through a refinery, fuel oil is flowing in a pipe at a velocíty of 7.5 m/s and a pressure of 202600 Pa. The pipe increased 5 m in height on a higher level. The diameter of the inlet pipe is 0.8 m and the outlet of the pipe is 0.95 m. The velocity of inlet and outlet are not the same. Determine the pressure at the outlet of the pipe if the density of fuel oil is 750 kg/m3 and gravity g is 9.8 m/s?.arrow_forwardQuestion 2: A reducing elbow is used to deflect water flow at a rate of 30 kg/s in a horizontal pipe upward by an angle 0 = 45° from the flow direction while accelerating it. The elbow discharges water into the atmosphere. The cross-sectional area of the elbow is 150 cm² at the inlet and 25 cm² at the exit. The elevation difference between the centers of the exit and the inlet is 40 cm. The mass of the elbow and the water in it is 50 kg. Determine the anchoring force needed to hold the elbow in place. Water 150 cm² 25 cm² 45° 40 cmarrow_forwardAir enters the fan through a duct at velocity of 6.3 m/s and an inlet static pressure of – 2.5 cm H2O W.G. The air leaves the fan through a duct at a velocity of 11.25 m/s and a discharge static pressure of 7.62 cm H2O W.G. If the specific weight of the air is 1.2 kg/m3 and the fan delivers 9.45 m3/s, what is the fan efficiency when the power input to the fan is 13.75 kW?arrow_forward
- A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated tank 25 ft above the reservoir surface through a 3 inch ID pipe. The inlet to the pump is located 10 ft below the water surface, and the water level in the tank is constant at 160 ft above the reservoir surface. The pump delivers 150 gal/min. If the total loss of energy due to friction in the piping system is 35 ft·lbf/lb, Calculate the horsepower required to do the pumping. The pump and its motor have an overall efficiency of 55 %. i. Determine the velocity of the water at point 2 in ft/s. ii. Assuming that the large open reservoir is open to the atmosphere as well, which of the following equations best describes the mechanical energy balance for the system? iii.The Reynolds number for the flow is?arrow_forwardA pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated tank 25 ft above the reservoir surface through a 3 inch ID pipe. The inlet to the pump is located 10 ft below the water surface, and the water level in the tank is constant at 160 ft above the reservoir surface. The pump delivers 150 gal/min. If the total loss of energy due to friction in the piping system is 35 ft·lbf/lb, Calculate the horsepower required to do the pumping. The pump and its motor have an overall efficiency of 55 %. i. What is Delta Z (Z2 - Z1) ? in ft. ii. Determine the theoretical shaft work required in foot-pound force per pound mass.. iii.Determine the actual shaft work needed for this particular mass flow rate in (ft-lbf)/s.arrow_forwardA cylindrical tank is being filled with water flowing with constant velocity V1 through a tap (Tap 1) that has an opening of diameter D1. The tank is initially empty and contains a tap (Tap 2) placed H1 m above the bottom of the tank that drains waterat a velocity of ? = √2?h. Assuming flow through Tap 2 starts the moment Tank 1 2height reaches H1 m, write the differential equation governing the change of water level inside the tank with time (?h =? );??i) Before water level reaches H1.ii) After water level reaches H1 up until the tank is full.Do NOT attempt to solve the differential equations!Just drive the differential equations and write the boundaries of the definite integrals.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Fluid Mechanics - Viscosity and Shear Strain Rate in 9 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=_0aaRDAdPTY;License: Standard youtube license