The 15-kg homogeneous bar AB supports the 30-kg block. The ends of the bar rest on frictionless inclines. Determine the distance x for which the bar will be in equilibrium in the position shown.

Q: The system shown is in equilibrium by the applied 250 N-force. Determine the pin reaction D. Neglect…

A: Given data: The applied load is P = 250 N. The horizontal distance between A and O is x = 125 mm.…

Q: 3. Determine the smallest horizontal force P that would push the homogenous cylinder of weight W…

A: As per given question  We have to find force required to puah the cylinder

Q: The 43-kg homogenecus smooth sphere rests on the 36° incline A and bears against the smooth vertical…

A:

Q: 400 Kg 2m 0,5 m 3m- 1 m

A:

Q: Determine the maximum downward force Pmax that can be applied to wedge A that wil keep the assembly…

A: Given: The weight of block C, W = 192 N

Q: The homogeneous block weights 250 N. Determine the value of P for which the block in equilibrium,…

A: Let us find the value of force P,  first, we draw the free body diagram. the weight acts downward in…

Q: The cylinder shown is homogeneous and has a mass of 30 kg. If slipping of the cylinder is prevented…

A: Draw the free body diagram for the above problem.

Q: The mass center G of the 1515-kg rear-engine car is located as shown in the figure. Determine the…

A:

Q: Cable AB passes over the small ideal pulley C without a change in its tension. What length of cable…

A:

Q: The 46-kg homogeneous smooth sphere rests on the 32° incline A and bears against the smooth vertical…

A: When an amount of push or the pull applied on the object, it has the ability to change its state…

Q: The mass center G of the 1350-kg rear-engine car is located as shown in the figure. Determine the…

A:

Q: The springs in are shown in the equilibrium position. 3m 3 m KAC = 20 N/m KAB = 30 N/m wwwww KAD-40…

A:

Q: The bobcat loader (Figure Q3) has a mass of 1200-kg, shows the center of mass is at G1. If there is…

A:

Q: the homogeneous cylinder of weight W=100 N rests in a frictionless right angled corner. determine…

A:

Q: The vertical mast supports the 6.2-kN force F and is constrained by the two fixed cables BC and BD…

A: Given:The force is .The distances are .The system is shown below.To find:The tension in the cable .

Q: Statics of Rigid Bodies (Equilibrium of Rigid Bodies) 3. The 25-kg rectangular access door is held…

A: The Answer is below

Q: The 45-kg homogeneous smooth sphere rests on the 42° incline A and bears against the smooth vertical…

A: Mass of sphere, m=45 kgInclination angle of A, θ=42o

Q: One of the smooth verticai walls supporting end B of the 235-kg uniform shaft is turned through a…

A:

Q: B NGA W E DAB C H ENERAL TOS CITY A DAME OF NOTRE WIVERSITY

A:

Q: The mass center G of the 1530-kg rear-engine car is located as shown in the figure. Determine the…

A: Given data- A car with weight given in equilibrium condition we have to find normal force at both…

Q: 7.5' |A 6.8' 0.6' B 2.4' 3.6' OFF HIO

A:

Q: 05: The 50-kg homogeneous smooth sphere resèts on the two inclines. Determine the contact forces at…

A:

Q: The homogeneous box has mass m. The magnitude of force P is slowly increased until motion occurs.…

A:

Q: If the mass of cylinder A is 41 kg, determine the tension in cable (DE) in order to hold the…

A:

Q: Consider the following system in static equilibrium. Force vector Facts at a distance" from the pin…

A: (a) Draw the free-body diagram of bar.

Q: 8. The uniform rod in the figure shown weighs 400N and has its center of gravity at G. Determine the…

A:

Q: The 53-kg homogeneous smooth sphere rests on the 40° incline A and bears against the smooth vertical…

A:

Q: Determine the n- and t-components of the force F which is exerted by the rod AB on the crank OA.…

A:

Q: The weight of the uniform bar AB is W. The stiffness of the ideal spring attached to B is k and the…

A:

Q: draw the free-body diagrams for the set (or structure) complete and each of its parts. Ignore…

A: (a) Free-body diagram of the complete structure is given as, At points A and B, the hinge joints…

Q: Determine the force (F) which applied to ring A in order to keep the 250 lb *.cylinder B in…

A: As it is given that cylinder is in equilibrium, then the forces and moments acting on it are in…

Q: The machine shown is used to help load luggage into airliners. The combined mass of the conveyor and…

A: Initially, we will disassemble the apparatus and create the conveyor's free-body diagram.The baggage…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.