A three-phase transformer connection has a delta-connected secondary, and one of the transformers has been center-tapped to form a neutral conductor. The phase-to-neutral value of the center-tapped secondary winding is 120 V. If the high leg is connected to a single-phase load, how much voltage will be applied to that load?

A three-phase transformer connection has a delta-connected secondary, and one of the transformers has been center-tapped to form a neutral conductor. The phase-to-neutral value of the center-tapped secondary winding is 120 V. If the high leg is connected to a single-phase load, how much voltage will be applied to that load?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.11MCQ: For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the...

See similar textbooks

Similar questions

In the circuit in Figure 2, the capacitor connected to the a-b terminals of the transformer anda circuit consisting of resistance is defined as a load circuit. a)Find the average power spent by the load circuit? b) How much of the average power calculated in a) by the resistance in the load circuit and how muchspent by the capacitor? Comment on the results obtained?
The equivalent circuit impedances of a 20-kVA, 8000/240-V, 60-Hz transformer are to be determined. The open-circuit test and the short- circuit test were performed on the primary side of the transformer, and the following data were taken: Open-circuit test (on primary) Short-circuit test (on primary) 8000 V V= 489 V I0.214 A 2.5 A P= 400 W P= 240 W Find the impedances of the approximate equivalent circuit referred to the primary side, and sketch the circuit.
74. The eddy-current loss in a 6.9 kV, 50 Hz transformer is 220 W. What will be the eddy-current loss of this transformer if it is to be connected across a 6.6 kV, 60 Hz source? A. 201 W C. 234 W B. 224 W D. 212 W
If you have 3-phase power and you need to step down (or up) in 3-phase voltage, how many single-phase transformers are needed? Explain.
Example 2-2. The equivalent circuit impedances of a 20-kVA, 8000/240-V, 60-Hz transformer are to be determined. The open-circuit test and the short-circuit test were performed on the primary side of the transformer, and the following data were taken: Open-circuit test (on primary) Short-circuit test (on primary) Voc = 8000 V Vsc = 489 V loc = 0.214 A Isc = 2.5 A Voc = 400 W Ps = 240 W
A voltage transformer in Figure 8 has 1,500 turns of wire on its primary winding and 500 turns of wire for its secondary winding. What will be the turns ratio, a of the transformer. If 240 volts is applied to the primary winding, what will be the resulting secondary voltage. And if a 400 n resistor is connected to the secondary winding, what are the values of current Is and Ip. primary Vp Transformer Core NF Ns Figure 8 secondary Vs
Q2 During routine tests of a three phase transformer, measurements of DC resistance between winding terminals is noted down. What kind of information can be obtained from the values so noted?
Answer only please The resistance of a transformer winding is 0.25 ohm at 25oC. When operating at full load, the temperature of the winding is 75oC. The temperature coefficient of resistance for copper at 0oC is 0.00427 per oC. What is the winding resistance at full load? a. 0.512 ohm b. 0.315 ohm c. 0.298 ohm d. 0.271 ohm
current? Why? 2-6. A 1000-VA, 230/115-V transformer has been tested to determine its equivalent cir- cuit. The results of the tests are shown below. Open-circuit test (on secondary side) Voc = 115 V loc = 0.11 A Poc = 3.9 W Short-circuit test (on primary side) Vsc = 17.1 V 1sc = 8.7 A Psc = 38.1 W (a) Find the equivalent circuit of this transformer referred to the low-voltage side of the transformer. (b) Find the transformer's voltage regulation at rated conditions and (1) 0.8 PF lag- ging, (2) 1.0 PF, (3) 0.8 PF leading. (c) Determine the transformer's efficiency at rated conditions and 0.8 PF lagging.
A 100/S00 V. 1 KVA, 50 Hz transformer was put through open and short-circuit tests to find its internal parameters. The test conditions and derived parameters are as follows Open circut test: The high voltage side terminals were open. The low voltäge side was connected to 10020ª, 50 Hz supply. The low voltage side current was measured as 50245º MA. Short-circuit test The high voltage side terminals were short-circuited. The low voltage side was connected to a variable voltage supply (50 Hz). A full load current of 102-30° A was achieved when the variable voltage supply was at 820° V. The transformer was then put to operation by connecting a load of 400230° 2 to the high voltage side (secondary) while applying a primary voltage of 10020º V. Calculate the primary current (the current drawn from the power supply).
If the secondary side of a dual-voltage single phase transformer, as per figure 1, were to be connected in series, the rated output current would be equal to the -A- current rating of the individual coils, B- sum of the current rating of the individual coils, C- either "a" or "b", D- neither "a" nor "b". If secondary side of the a dual-voltage single phase transformer, as per figure 1, were to be connected in paralle, the rated output current would be equal to the A- current rating of the individual coils, B- sum of the current rating of the individual coils, C- either "a" or "b", D- neither "a" nor "b". The poles of a magnet tend to be____________. A - at the ends of the magnet, B- in the middle of the magnet, C -all around the magnet, D- none of the above.
In the circuit in Figure 2, the capacitor connected to the a-b terminals of the transformer anda circuit consisting of resistance is defined as a load circuit. Find the average power spent by the load circuit?