Essential University Physics
4th Edition
ISBN: 9780134988559
Author: Wolfson, Richard
Publisher: Pearson Education,
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 12, Problem 38P
Figure 12.23 shows a 1250-kg car that has slipped over an embankment. People are trying to hold the car in place by pulling on a horizontal rope. The car’s bottom is pivoted on the edge of the embankment, and its center of mass lies farther back, as shown. If the car makes a 34° angle with the horizontal, what force must the people apply to hold it in place?
FIGURE 12.23 Problem 32
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
9.3
Chapter 12, Problem 034
In the figure, a thin horizontal bar AB of negligible weight and length L = 3.1 m is hinged to a vertical wall at A and supported at B by a thin wire BC that makes an angle e = 42° with the horizontal.
A block of weight W = 250 N can be moved anywhere along the bar; its position is defined by the distance x = 1.75 m from the wall to its center of mass. Find (a) the tension in the wire, and the
(b) horizontal and (c) vertical components of the force on the bar from the hinge at A.
Com
A
B
(a) Number
Units
(b) Number
Units
(c) Number
Units
Click if you would like to Show Work for this question:
Open Show Work
A 1-meter long, 20 kg uniform bar is attached to a wall by a hinge. It is held in a horizontal position
by a rope that makes an angle of 50 degrees with the wall. What is the y-component of tension in the
rope (FT)?
Answer in Newtons.
Chapter 12 Solutions
Essential University Physics
Ch. 12.1 - The figure shows three pairs of forces acting on...Ch. 12.2 - Prob. 12.2GICh. 12.3 - The figure shows a person in static equilibrium...Ch. 12.4 - Prob. 12.4GICh. 12 - Give an example of an object on which the net...Ch. 12 - Prob. 2FTDCh. 12 - Pregnant women often assume a posture with their...Ch. 12 - When you carry a bucket of water with one hand,...Ch. 12 - Is a ladder more likely to slip when you stand...Ch. 12 - Does choosing a pivot point in an equilibrium...
Ch. 12 - If you take the pivot point at the application...Ch. 12 - A short dog and a tall person are standing on a...Ch. 12 - Prob. 9FTDCh. 12 - A body is subject to three forces; F1=1i+2jN,...Ch. 12 - To demonstrate that the choice of pivot point...Ch. 12 - In Fig. 12.11 the forces shown all have the same...Ch. 12 - Figure 12.12a shows a thin, uniform square plate...Ch. 12 - Repeat the preceding problem for the equilateral...Ch. 12 - A 23-m-long log of irregular cross section lies...Ch. 12 - A 60-kg uniform board 2.4 m long is supported by a...Ch. 12 - Where should the child in Fig. 12.14 sit if the...Ch. 12 - A 4.2-m-long beam is supported by a cable at its...Ch. 12 - Figure 12.15 shows how a scale with a capacity of...Ch. 12 - A portion of a roller-coaster track is described...Ch. 12 - Prob. 21ECh. 12 - Prob. 22ECh. 12 - Prob. 23ECh. 12 - Example 12.2: Climbers attempting to cross a...Ch. 12 - Example 12.4: Consider the potential-energy curve...Ch. 12 - Prob. 27ECh. 12 - Prob. 28ECh. 12 - Youre a highway safety engineer, and youre asked...Ch. 12 - Figure 12.17a shows an outstretched arm with mass...Ch. 12 - A uniform sphere of radius R is supported by a...Ch. 12 - You work for a garden equipment company, and youre...Ch. 12 - Figure 12.20 shows the fool and lower leg of a...Ch. 12 - A uniform 5.0-kg ladder is leaning against a...Ch. 12 - The boom in the crane of Fig. 12.21 is free to...Ch. 12 - A uniform board of length L and weight W is...Ch. 12 - Figure 12.23 shows a 1250-kg car that has slipped...Ch. 12 - You are headwaiter at a new restaurant, and your...Ch. 12 - You are headwaiter at a new restaurant, and your...Ch. 12 - Prob. 41PCh. 12 - A crane in a marble quarry is mounted on the...Ch. 12 - A rectangular block measures w w L, where L is...Ch. 12 - The potential energy as a function of position for...Ch. 12 - A rectangular block of mass m measures w w L,...Ch. 12 - A 160-kg highway sign of uniform density is 2.3 m...Ch. 12 - Prob. 47PCh. 12 - Prob. 48PCh. 12 - A uniform, solid cube of mass m and side s is in...Ch. 12 - An isosceles triangular block of mass m and height...Ch. 12 - Youre investigating ladder safety for the Consumer...Ch. 12 - A 2.0-m-long rod has density in kilograms per...Ch. 12 - What horizontal force applied at its highest point...Ch. 12 - A rectangular block twice as high as it is wide is...Ch. 12 - What condition on the coefficient of friction in...Ch. 12 - A uniform solid cone of height h and base diameter...Ch. 12 - Prove the statement in Section 12.1 that the...Ch. 12 - Three identical books of length L are stacked over...Ch. 12 - A uniform pole of mass M is at rest on an incline...Ch. 12 - For what angle does the situation in Problem 53...Ch. 12 - Figure 12.31 shows a popular system for mounting...Ch. 12 - The nuchal ligament is a thick, cordlike structure...Ch. 12 - A 4.2-kg plant hangs from the bracket shown in...Ch. 12 - The wheel in Fig. 12.34 has mass M and is weighted...Ch. 12 - An interstellar spacecraft from an advanced...Ch. 12 - Prob. 66PCh. 12 - Engineers designing a new semiconductor device...Ch. 12 - Youve been hired by your states environmental...Ch. 12 - Youve been hired by your states environmental...Ch. 12 - Youve been hired by your states environmental...Ch. 12 - Youve been hired by your states environmental...
Additional Science Textbook Solutions
Find more solutions based on key concepts
Some organizations are starting to envision a sustainable societyone in which each generation inherits sufficie...
Campbell Essential Biology (7th Edition)
10.71 Identify each of the following as an acid or a base: (10.1)
H2SO4
RbOH
Ca(OH)2
HI
...
Chemistry: An Introduction to General, Organic, and Biological Chemistry (13th Edition)
Which compound is more easily decarboxylated?
Organic Chemistry (8th Edition)
What are four functions of connective tissue?
Anatomy & Physiology (6th Edition)
Match each of the following items with all the terms it applies to:
Human Physiology: An Integrated Approach (8th Edition)
Two culture media were inoculated with four different bacteria. After incubation, the following results were ob...
Microbiology: An Introduction
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- A new art exhibit featuring mobile works is going up in the Holland, MI, area. One piece is shown in the figure. The 140-N uniform beam is pinned to the ground by a pivot. The beam is supported by a cable (attached to the center of the beam) to allow for each of the shoes to hang freely. Each individual shoe has a weight of 9.5-N. 1.If one shoe is attached two-fifths of the way up the beam and another shoe is attached and three-fifths of the way up the beam, with θc = 19.5° and θb = 33.5° as shown in the figure, what is the tension in the cable, in newtons?arrow_forwardA 5 kg beam 2 meters long is used to support a 10 kg sign by means of a cable attached to a building. The signs hangs from the end of the 2 m long beam, and the cable makes a 40 degree angle with the beam. What is the tension in the cable?arrow_forwardTwo people are carrying a uniform wooden board that is 3.00 m long and weighs 160 N. If one person applies an upward force equal to 60 N at one end, at what point does the other person lift? Begin with a free-body diagram of the board.arrow_forward
- Mark is trying to rescue Mary from a castle by climbing a uniform ladder that is 5 m long and weighs 180 N. Mark, who weighs 800 N, stops a third of the way up the ladder . The base of the ladder rets on a horizontal ground and leans in equilibrium against a vertical frictionless wall. The ladder makes an angle of 53.1 degrees with the horizontal, and forming a 3-4-5 right triangle. Find the force exerted by the ground at the base of the ladderarrow_forwardA person with a 800 N weight is standing 2 meters from the left of a five meter wide uniform plank that weights 1200 N. The plank is held by two verticla ropes on either end. What are the tensions of both ropes?arrow_forwardA 800 N man is standing on a 4 m long plank of wood that is supported at each end by vertical ropes. The plank has a weight of 500 N and the man is standing 1 m from the left end. Find the force of tension in the rope at the left end of the plank.arrow_forward
- A 24 kg rectangular 4.00 m x 3.00 m rectangular sign is suspended from a horizontal 6.00 m long rod with a 5 kg mass as indicated in the figure. The left end of the rod is supported by a hinge, and the right end is supported by a thin cable making a 30.0° angle with the vertical. Draw a free body diagram and calculate the tension T in the cable. The thin cable breaks if it is pulled by more than 200 N. Show than in the present situation the cable can not support the sign without breaking. Show the cable is able to support the load if it is attached higher up such that it makes an angle of 20.0° angle S0.0 CE CREAM SHOP with the vertical.arrow_forwardA uniform, 8.0-m, 1500-kg beam is hinged to a wall and supported by a thin cable attached 2.0 m from the free end of the beam. The beam is supported at an angle of 30° above the horizontal. (a) find the tension in the cable and (b) how hard does the beam push inward on the wall?arrow_forwardA person who weighs 775 N supports himself on the ball of one foot. The normal force N = 775 N pushes up on the ball of the foot on one side of the ankle joint, while the Achilles tendon pulls up on the foot on the other side of the joint. The center of gravity of the person is located right above the tibia. What is the tension in the Achilles tendon? If the force acting is upward, enter a positive value and if the force acting is downward, enter a negative value.arrow_forward
- A bodybuilder holds a dumbbell of weight Wd. His arm is horizontal and weighs 47 N. The deltoid muscle is assumed to be the only muscle acting and is attached to the arm as shown. The maximum force M that the deltoid muscle can supply has a magnitude of 2481 N. The distances that locate where the various forces act on the arm. What is the weight of the heaviest dumbbell that can be held by the bodybuilder? Note: Express your answer in whole numbers. No unit is required for the final answer. M. ... r13.0° +y Wa 0.150 m 0.280 m +T 0.620 m (b) Free-body diagram of the arm M Deltoid Dumbbell 13.0 muscle Axis Shoulder joint (a) (c)arrow_forwardBart ( whose mass is 31.1 kg) and Milhouse (whose mass is 20.4 kg) sit balanced on a teeter -totter that has its pivot point at its exact center . If the two boys are separated by a distance of 2.52 m, at what distance (in m) from the pivot point must Milhouse be sitting at in order to maintain the balance? Explain how you solved the problem involving children balancing on a teeter-totter. Be sure to state what your known and unknown quantities are, what concepts were applied, and what equations were used!arrow_forwardIn the figure, a thin horizontal bar AB of negligible weight and length L is hinged to a vertical wall at A and supported at B by a thin wire BC that makes an angle 0 with the horizontal. A block of weight W can be moved anywhere along the bar; its position is defined by the distance x from the wall to its center of mass. Find (a) the tension in the wire, and the (b) horizontal and (c) vertical components of the force on the bar from the hinge at A. State your answers in terms of the given variables. (Note: the positive x direction is to the right, and the positive y direction is up) com B (a) ? Edit (b) Edit (c) Editarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- College PhysicsPhysicsISBN:9781305952300Author:Raymond A. Serway, Chris VuillePublisher:Cengage LearningUniversity Physics (14th Edition)PhysicsISBN:9780133969290Author:Hugh D. Young, Roger A. FreedmanPublisher:PEARSONIntroduction To Quantum MechanicsPhysicsISBN:9781107189638Author:Griffiths, David J., Schroeter, Darrell F.Publisher:Cambridge University Press
- Physics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningLecture- Tutorials for Introductory AstronomyPhysicsISBN:9780321820464Author:Edward E. Prather, Tim P. Slater, Jeff P. Adams, Gina BrissendenPublisher:Addison-WesleyCollege Physics: A Strategic Approach (4th Editio...PhysicsISBN:9780134609034Author:Randall D. Knight (Professor Emeritus), Brian Jones, Stuart FieldPublisher:PEARSON
College Physics
Physics
ISBN:9781305952300
Author:Raymond A. Serway, Chris Vuille
Publisher:Cengage Learning
University Physics (14th Edition)
Physics
ISBN:9780133969290
Author:Hugh D. Young, Roger A. Freedman
Publisher:PEARSON
Introduction To Quantum Mechanics
Physics
ISBN:9781107189638
Author:Griffiths, David J., Schroeter, Darrell F.
Publisher:Cambridge University Press
Physics for Scientists and Engineers
Physics
ISBN:9781337553278
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Lecture- Tutorials for Introductory Astronomy
Physics
ISBN:9780321820464
Author:Edward E. Prather, Tim P. Slater, Jeff P. Adams, Gina Brissenden
Publisher:Addison-Wesley
College Physics: A Strategic Approach (4th Editio...
Physics
ISBN:9780134609034
Author:Randall D. Knight (Professor Emeritus), Brian Jones, Stuart Field
Publisher:PEARSON
An Introduction to Stress and Strain; Author: The Efficient Engineer;https://www.youtube.com/watch?v=aQf6Q8t1FQE;License: Standard YouTube License, CC-BY