Concept explainers
In a work situation where an electrician’s hands get wet while operating a 120-volt, corded drill, which of the following would be true? (Objective 1-1)
a. Body resistance increases, and any shock would be mild.
b. Body resistance remains the same, and there is no danger as Long as rubber boots are worn.
c. Body resistance is substantially decreased, and severe shock could occur.
d. There is no danger as Long as a three-prong plug is used.
The true statement for the situation where an electrician’s hands get wet while operating a
Answer to Problem 1RQ
Option (c) Body resistance is substantially decreased, and severe shock could occur.
Explanation of Solution
Introduction:
According to the Ohm’s law, the relation between the current, voltage, and resistance is given by,
Here, the current is in amperes, voltage is in volts, and resistance is measured in Ohm’s.
The flow of current through any material depends upon the resistance provided by the material. The higher is the circuit resistance, the lower the current flow that a voltage can push through the circuit and vice-versa.
Dry skin offers much more resistance in comparison to the wet body. This means that higher the resistance value, the more opposition to the current flow through the body.
The following table shows the value of resistance with respect to the different conditions:
Skin Condition | Resistance |
Dry skin | |
Sweaty hands | |
In water |
As shown in the above table, the value of resistance for wet hands is very less so if in a work situation where an electrician’s hands get wet while operating a
As shown in the above table, the value of resistance for wet hands is very less, so the shock will not be mild. Thus, option (a) is incorrect.
Therefore, the body resistance will not remain the same if the hand gets wet. Thus, option (b) is incorrect.
The electrician will always be in danger if his hands are wet. Thus, option (d) is incorrect.
Conclusion:
Therefore, the Option (c) Body resistance is substantially decreased, and severe shock could occur is best suitable answer for the given statement.
Want to see more full solutions like this?
Chapter 1 Solutions
Residential Construction Academy: House Wiring (MindTap Course List)
- 1. A water sample has an influential alkalinity of 123 mg/L as CaCO3. Ferric Sulfate is added at a dose of 73 mg/L for coagulation. Assume all alkalinity is HCO3- and ignore all side reactions. A) How much alkalinity is consumed in the coagulation reaction (in meq/L)? B) How much alkalinity remains after coagulation (in mg/L as CaCO3)arrow_forwardGiven M = 54 kip-ft, w = 12 kip/ft, P = 32 kip, a 3 ft, b = 9 ft, c = 3 ft. M W b с Determine the reaction at C. Determine the magnitude of the maximum positive bending moment. Determine the reaction at B. Determine the absolute value of the maximum bending moment in the beam.arrow_forwardFor the three-pinned frame shown in picture i am trying to detemine the: 1. Determine the reactions at supports A and B. 2. Draw the shear force diagram for member AC. 3. Draw the bending moment diagram for member BFE. 4. Draw the axial force diagram for member CD. 5. Determine the maximum bending moment in member AC. Detail answer with actual calculations and drawings please for better comprehension. I have tried to attempt this question multiple times, however if seems to be incorrect. I will upvote, if answer is detailed Thank youarrow_forward
- The cross-sectional dimensions of the beam are shown in figure.[a= 5 in., b= 11 in., t= 1 in.] H a y K 12 a b What is distance of the centroid from the top of the section? What is the moment of inertia about the z-axis?arrow_forwardDetermine the following for the section shown in the figure. [b 12 in., t 1 in., hw = 9 in., tw = 0.5 in.] bi T tw If hw Determine the distance of centroid from the top of the section. Determine the moment of inertia for the entire section.arrow_forwardI need detailed help solving this exercise from homework of Mechanics of Materials. The answer should be F=323kN/m, but I do not really understand the process. Please do it step by step, not that long but clear. Thank you!arrow_forward
- The beam shown in the figure is subjected to a moment M and a concentrated force P. [P = 12 kips, M = 19 kip-ft a = 3 ft, b = 5 ft, c 5 ft, d = 5 ft., RB = 5.27, RE = 6.73] M a B b C C P D E d What is the maximum absolute value of the shear force in the beam? What is the maximum absolute value of the bending moment in the beam?arrow_forwardI need detailed help solving this exercise from homework of Mechanics of Materials. I do not really understand, please do it step by step, not that long but clear. Thank you!arrow_forwardI need detailed help solving this exercise from homework of Mechanics of Materials. I do not really understand, please do it step by step, not that long but clear. Thank you!arrow_forward
- I need detailed help solving this exercise from homework of Engineering Math. I do not really understand, please do it step by step, not that long but clear. Thank you!arrow_forwardI need detailed help solving this exercise from homework of Engineering Math. I do not really understand, please do it step by step, not that long but clear. Thank you!arrow_forwardI need detailed help solving this exercise from homework of Engineering Math. I do not really understand, please do it step by step, not that long but clear. Thank you!arrow_forward
- Residential Construction Academy: House Wiring (M...Civil EngineeringISBN:9781337402415Author:Gregory W FletcherPublisher:Cengage LearningSolid Waste EngineeringCivil EngineeringISBN:9781305635203Author:Worrell, William A.Publisher:Cengage Learning,