You are asked to design a water softening system to bring following water to a final hardness if 75.0 mg/L as CaCO3. The ion concentrations reported below are all mg/L as CaCO3. Ca2+ = 240.00; Mg2+ = 90.0; HCO3- = 268.0; and CO2= 18.0 The total lime required and initial NCH are nearly 1. 330 and 268 mg/L as CaCO3 2. 376 and 62 mg/L as CaCO3 3. 330 and 27 mg/L as CaCO3 4. 376 and 268 mg/L as CaCO3

You are asked to design a water softening system to bring following water to a final hardness if 75.0 mg/L as CaCO3. The ion concentrations reported below are all mg/L as CaCO3. Ca2+ = 240.00; Mg2+ = 90.0; HCO3- = 268.0; and CO2= 18.0 The total lime required and initial NCH are nearly 1. 330 and 268 mg/L as CaCO3 2. 376 and 62 mg/L as CaCO3 3. 330 and 27 mg/L as CaCO3 4. 376 and 268 mg/L as CaCO3

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter3: Weight-volume Relationships And Plasticity

Section: Chapter Questions

Problem 3.1P

See similar textbooks

Similar questions

What dosage of lime with a purity of 90% of CaO is required to combine 35 mg/l of calcium.
6-3. Estimate the amount of lime, in tons/d, required to soften 5 MGD of water to the practical solubility limits. The constituent concentrations are as follows: Co, = 0.44 meq/L Ca²+ = 4.76 meq/L Mg²* = 1.11 meq/L Alkalinity = 3.96 meq/L CI" = 1.91 meq/L so; = 1.58 meq/L %3D
formed? Q1: B: The specific gravity and absorption test was performed on fine aggregate and the following data were obtained: Mass of SSD sand = 500.0 g Mass of pycnometer with water only = 623.0 g Mass of pycnometer with sand and water= 938.2 g Mass of dry sand = 495.5 g Calculate the specific gravity values (dry bulk, SSD, and apparent) and the absorption of the fine aggregate.
For a natural raw water containing the following water quality in the table. Check lecture 05 slides on page 52 to determine how much slaked lime is needed remove all hardness. Atomic weight or molecular Concentration weight (g/mol) 120 mg/L 100 mg/L as CaCO3 25 meg/L Ca2+ 40 Mg2+ HCO3 24 61 O A. 5 meq/L О В. 700 mg-СаСОЗ/L O C. 15 meq/L O D. No lime is needed.
please provide step by step solutions and draw the lever on the graph as well. i know the answers. (c) About 1250 C (d) Fe3C, cementite (e) About 0.7 wt% C, about 72% (f) About 40%, no. (h) Draw the microstructure of a 1.5 wt.% C material that has been heated to 1200 C and then slowly cooled to 600 C. Clearly label all phases.
Q3 According to hardening behaviors, binding materials are grouped into air hardening and water hardening binding materials. (1). What is air hardening binding materials and please list three kinds of air hardening binding materials.. (2). How to produce lime and what are the main technical properties of lime? ( (3). What are the main applications of lime?
Complete the sieve examination table for aggregates below and calculate the fineness coefficient
Strength requirements, in MPa – 30.68 Mpa Water cement ratio, in decimal – 0.45 Coarse aggregate requirements (dry), in kg/m3 – 992.kg/m3 Air content, in percent – 3.5% Water content, kg/m3 – 184 kg/m3 Cement, in kg/m3 – 408.89 kg/m3 Determine the Admixtures in ml/m3 Fine aggregate requirements (dry), in kg/m3 Net Water Content, in kg/m3
A sieve analysis test was conducted for sample of fine aggregate and obtained the results as shown in Table Q1. Calculate the percent passing of each sieve and classify the fineness of fine aggregate based on fineness modulus analysis. (c)
19 docs.google.com/forms subjected to stress, it breaks with little elastic deformation and without significant plastic deformation True False - Tensile stress to bars, column , etc lead to shortening this sample. True False - Semi hydraulic lime is an intermediate between Dolomatic and Hydraulic lime True False العربية الإنجليزية ...
Based on a sieve analysis test, 12% of the aggregate sample was retained on the first (top) sieve and 10% of the aggregate sample was retained on the second sieve, and 38% of the aggregate sample was retained on the third sieve. What is the cumulative percent retained on third sieve? 74% 72% 60% O 40%
H.W. Fine aggregate sample was tested to find its physical properties. The test results were as follows: Bulk specific gravity= 2.45, Apparent specific gravity 2.5, mass of the vessel full of water = 1300 gm, mass of the vessel plus sand and topped up with water= 1500 gm, mass in wet condition 518 gm. Calculate 1- absorption% 2- moisture content% 3- Bulk density 4- Apparent density A-D % Absorption = D D- (B-C) Apparent Specific Gravity = Container SSD Aggregate (A) OD Aggregate (D) Container SSD Bulk Sp.Gr. = with H,O (C) with H,O and with A-(B-C) Aggregate (B) Weight of Agg. (W,) Sp.Gr.= Weight of an equal volume of water (V,*P) PA Density of Agg. Pw Density of Water