xpress all answers in significant figures and scientific notation.  The  elastic  limit  of  Al is   1.8 X 10^8 Pa.  Find  the  minimum   radius (meter) of  an Al wire  that  could  support  a  10.0  kg mass without  surpassing its  elastic  limit

Q: our biceps muscle is attached to your elbow by the distal biceps tendon. An average adults tendon…

A:

Q: A steel cube of side length L = 0.5 m is subjected to a shearing force of 5000N along the top…

A:

Q: A strand of dragline spider silk has a diameter of 6.0 μm, and can support a mass of 2.9 g.…

A: Required : Approximately how many copper wires would it take tosupport the same mass?

Q: )A strand of dragline silk is 6 um about in diameter, about 10% the diameter of a human hair. What…

A:

Q: The five-bolt connection shown must support an applied load of P = 480 kN. If the average shear…

A:

Q: A copper (shear modulus 4.2 x 1010 N/m²) cube, 0.442 m on a side, is subjected to two shearing…

A:

Q: An 9.63-kg stone at the end of a steel (Young's modulus 2.0 x 1011 N/m²) wire is being whirled in a…

A: The strain in the wire is strain=LΔL​=2.43×10−4Explanation:Step 1: Given- The mass of the stone is…

Q: What is the maximum load that could be suspended from a copper wire of length 1.00 m and radius 1.08…

A:

Q: 1. A frame ABC shown in Figure 2 consists of a tension member AB and a compression member BC. Member…

A: Given that  Mdulus of elasticity,E=200 GPa=200×109Pa Horizontal force,H=150 kN=150×103N Length,L=3.5…

Q: The “lead” in pencils is a graphite composition with Young’s modulus of approximately 1.0×109 N/m2.…

A:

Q: An arbitrary material has an elastic modulus of 118 GPa. How much tensile force was applied to a 100…

A: Given that: Y=118 GPa=118×109 PaL=100 mmD=10 mmReduction of area= 0.1% of initial areaσ=0.29

Q: A tensile stress is to applied along the long axis of a cylindrical brass rod that has a diameter of…

A:

Q: modulus (Y) and energy density (E). The strain A stretching wire has a Young's in a stretching wire…

A: To find-Strain in wire=?Given-Young's modulus=YEnergy density=E

Q: Many caterpillars construct cocoons from silk, one of the strongest naturally occurring materials…

A:

Q: A steel rod 55 cm long has a diameter of 35.0 cm. The compressive strength (the maximum stress it…

A:

Q: A mineshaft has an ore elevator hung from a single braided cable of diameter 2.5 cm. Young’s modulus…

A:

Q: Part 1. A force stretches a (first) wire by 2mm. This wire is made of an unknown material and has a…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: A tendon is subjected to tensile forces. The cross-sectional area of the tendon is 0.0002 m2. If the…

A: See below

Q: Three liquids that will not mix are poured into a cylindrical container. The volumes and densities…

A:

Q: A solid copper cube has an edge length of 82.4 cm. How much stress must be applied to the cube to…

A: Write the given values with the suitable variables. L1=82.4 cm=0.824 mL2=82 cm=0.82 mK=1.4×1011 N/m2…

Q: A biomechanical model of the bones and biceps muscles of a person's arm supporting a mass m=2 kg is…

A: Stress is a quantity that describes the magnitude of forces that cause deformation. Stress is…

Q: Q2c) Listed in the table below is the tensile stress-strain data for different grades of steels.…

A: Given Listed in the table below is the tensile stress-strain data for different grades of steel, as…

Q: Four wire of the same material but having different lengths subjected to same load. Which of the…

A: To find- Length of wire. Combination of length (L) and radius (r) which has highest elongation.…

Q: A solid copper cube has an edge length of 82.4 cm. How much stress must be applied to the cube to…

A: The initial edge length of the cube is ai = 82.4 cm = 0.824 m The final edge length of the cube is…

Q: The leg bone (femur) breaks under a compressive force of about 8.20 × 104 N for a human and 11.7 ×…

A: Compressive force for human bone ( F human ) = 8.20 × 104 N Compressive force for horse bone ( F…

Q: Polymer in the form of a cylinder with a length of 100 mm and a diameter of 5 mm. If a load is…

A:

Q: A solid copper cube has an edge length of 89.9 cm. How much stress must be applied to the cube to…

A: The ratio of volumetric stress with volumetric strain is defined as the bulk modulus. To solve the…

Q: A solid copper cube has an edge length of 81.6 cm. How much stress must be applied to the cube to…

A: Given: L=81.6 cmL'=81.0 cmB=1.4*1011 N/m2

Q: A solid copper cube has an edge length of 85.9 cm. How much stress must be applied to the cube to…

A: Given: length of cube l = 85.9 cmfinal length =86cmchange in length ∆l = 86-85.9 = 0.1 cmBulk…

Q: A tow truck is pulling a car out of a ditch by means of a steel cable that is 9.2 m long and has a…

A: Given data: The length of the steel cable is L=9.2 m. The radius of the steel cable is R=0.50 cm.…

Q: The leg bone (femur) breaks under a compressive force of about 9.00 × 104 N for a human and…

A: Given: Force to break a human leg FH = 9 x 104N            Compressive Strength (Pressure) of human…

Q: The true stress-strain behavior of a metal is given by otrue = K- (Etrue)", where Otrue is the true…

A: Given, σtrue=Kεtruen

Q: The plot of tensile stress vs tensile strain of a certain rod has a slope of 23-GPa in the elastic…

A: Given data:  Slope of tensile stress vs tensile strain graph = 23 GPa Tensile strain (ε) =…

Q: An 11.2-kg stone at the end of a steel (Young's modulus 2.0 x 1011 N/m²) wire is being whirled in a…

A:

Q: A cable supports a lift that moves up with an upward acceleration of 2 m/s2. Given that the…

A: Given, Upward acceleration,a=2 m/s2 Proportional limit stress,σ=10.1×109N/m2 Area of…

Q: The free body diagram must be included. Mechanics of materials (mechanical engineering) Stop using…

A: Step 1:Step 2: Step 3: Step 4:

Q: Prob 5.13 A structural steel rod 1 inches in diameter and 25 feet long, in supporting a balcony,…

A: The modulus of elasticity E is given as E=stressstrain=FLA∆LF=tensile forceA=area of cross…

Q: An aluminium (p = 2.7g/cm³) wire is suspended from the ceiling and hangs vertically. How long must…

A: Given that-Density of aluminium wire, ρ=2.7g/cm3Stress at upper end, σt= 8×107 N/m2We know…

Q: An aluminium (p = 2.7g/cm³) wire is suspended from the ceiling and hangs vertically. How long must…

A: Given that-Density of aluminium wire, ρ=2.7g/cm3Stress at upper end, σt= 8×107 N/m2We know…

Q: steel wire 2.0 mm in diameter stretches by 0.029 % when a mass is suspended from it. The elastic…

A:

Q: A solid copper cube has an edge length of 88.9 cm. How much stress must be applied to the cube to…

A:

Mechanical Properties of Solids

There are three types of matter- solid, liquid and gas. Out of them, solids have a rigid shaped and size. The intermolecular forces of attractions in solids are greatest. Mechanical properties are the physical properties of a material which it shows, when it is provided with certain amount of force or load. These properties are to be kept in mind for various purposes. When a force is applied to an object, the object may or may not get deformed depending upon its elastic property. But every time the object develops a restoring force against the force applied. This is commonly known as stress. If the object changes its dimensions due to the force applied it develops strain ( which is the ratio of change in dimension to the original dimension).