x-: The tongs are used to grip the ends of the drilling pipe P. If a torque (moment) of Mp = 900 lb- ft is needed at point P to turn the pipe, determine the cable force F that must be applied to the tongs. Set 0 = 40°. (1 ft = 12 in.) 6 in. Mp 43 in. x- For question (Q2) above, if 0 = 80°, what do you think the cable force will be? (Circle one)

x-: The tongs are used to grip the ends of the drilling pipe P. If a torque (moment) of Mp = 900 lb- ft is needed at point P to turn the pipe, determine the cable force F that must be applied to the tongs. Set 0 = 40°. (1 ft = 12 in.) 6 in. Mp 43 in. x- For question (Q2) above, if 0 = 80°, what do you think the cable force will be? (Circle one)

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.84P: The cable supports three 400-lb loads as shown. If the maximum allowable tension in the cable is 900...

See similar textbooks

Similar questions

6 in 60° 20 in Statics Instructor A vertical force of P = 100 lb is required to remove the nail at C from the board. Determine the magnitude of the moment about B exerted by the 100 lb vertical force. Draw a free body diagram for the system. Then, use what you know about moments to solve for Mp What is the magnitude of the moment at point B due to P if P = 100 lb and 9 = 10"? Round to the nearest whole number. Enter a response then click Submit below lb in
The L-shaped rod AOCD has an 80 kg mass hanging from it at B. The rod is leaning against a smooth wall at A. Point B is half way up OA. There is a journal bearing at C and a thrust bearing at D. They are properly aligned. A force F is pulling in the x-direction at B. Just as the rod comes off of the wall at A, what is the magnitude of the force F. 1 m B F 1m
F- 10N 250 mm The 10-N force is applied to the handle of the hy- draulic control valve as shown. Calculate the mo- 60 17.5 mm ment of this force about point O.
י וו, ו> E 11;EV I 2 T3- 3D For.. T3 3D - Force Syste Q8 The 180-lb force is applied at point A of the bracket. Determine the moments of this force about point B, about point C, and about the line BC. Ans. Mc= -2840k Ib.in MBc =2540 Ib.in 6" 13" 180 lb 145 09 15" 12 II
Determine A·(B×C) The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by two cables at B. A force P is applied at B where P = 11i - 10j kN.Note that the reaction force at A acts along the boom because it is a two-force member. Calculate the magnitude of the reaction force at A in kN Determine the magnitude of the moment of P about the origin (point O) in Nm.
A member is loaded with the given system of forces Find the moment about C & D. Where AB = AD = 70 m, F1=35 N F2=50N, F3=63N, F4=48N, e1=35°, e2= 50°, 03=25° & 604=60°. (Enter only the values in the boxes by referring the unit given in brackets. Also upload your hand written answers in the link provided) shown in figure. F2 A D Өз F4 The Moment about "C" (in Nm) = The Moment about "D" (in Nm) =
2. Find the forces acting at pins C and D of the given frame. loworod slowly onto 2.2 m -3 m 2m DI 3 m3 m- B 4 m 240 N
600 lb 2.5 ft 2.5 ft 2.5 t 2.5 ft E 1. The structure is: 2. The two-force member is: AB and CD v and its 3. Given that Fx +1000 Ib and Fy =+1000 Ib (Hint: take the moments at B), the magnitude of internal force FCD is:
The wheels, axle, and handles of a wheelbarrow weigh W = 55 N. The load chamber and its contents weigh WL = 623 N. The drawing shows these two forces in two different wheelbarrow designs. To support the wheelbarrow in equilibrium, the man’s hands apply a force to the handles that is directed vertically upward. Consider a rotational axis at the point where the tire contacts the ground, directed perpendicular to the plane of the paper. Find the magnitude of the man’s force for both designs.
Q3/ calculate the moment of the 60N force about point O for the condition 0= 30 60N 1600mm 1200mm
Based on Problem 4-9 from the textbook. The cable exerts a force P at the end of the crane boom. Determine the position of the boom so that force P creates a maximum moment about point O. What is this moment? Unique Values for Each Student: A P= 5.4 KN x= 11.5 m Y = 6-8 m P B 0 1'm O M IMI 1
Find the moment about A & B, where AB = AD = 12 m, F1= 4 N, F2 = 8 N, F3 = 13 N & F4 = 19 N. Each force is acting at the mid-point of each side. -- 4 Marks %3D %3D F1 F2 F4 D F3 (NOTE: ENTER ONLY THE VALUES BY REFERRING TO THE UNITS GIVEN IN THE BRACKET. ALSO, SUBMIT THE HANDWRITTEN ANSWER SHEET IN THE LINK PROVIDED) The moment of force about "A" (in Nm) (2 Marks) %3D The moment of force about "B" (in Nm) = (2 Marks) %3D