-- A force sensor system is given in figure. The force squezes a spring (withK=100N/mm) through a massless piston which is connected to wiper of 500-Ohmlinear potentiometer with sensitivity of 8 Ohm/mm. The potentiometer input(supply) voltage is 1Voc and the output is propotional to force via sensing setup.The spring displacement (y) is measured from its initial (F=0) positon. The forcemeasurement is displayed on a computer screen.-Ireut Valtege-6 +5)*100] towwwsing Centect(b) The force applied to spring is changes from [{6 +10)*400] Newtons. Design required amplifier circuit(s)for scaing the force range voltage output to 0 to 5V., .Outpet varege

Answered: Image /qna-images/answer/9d0cf2cd-daec-4e9c-9718-df02aa8eb652.jpg

www 6 +5)*100] to 6 +10)*400] Newtons. Design required amplifier circuit(s) for scaing the force range voltage output to 0 to 5V., .; (b) The force applied to spring is changes from [( Jding Centect

www 6 +5)100] to 6 +10)400] Newtons. Design required amplifier circuit(s) for scaing the force range voltage output to 0 to 5V., .; (b) The force applied to spring is changes from [( Jding Centect

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

QUESTION 4 In this voltage divider bias circuit, the input is at the base. Output is at the emitter with a high input resistance and low output resistance. The maximum voltage gain is 1 and the coupling capacitors must have a negligible reactance at the frequency of operation. (use to answer a and b) a. Derive the expression for the voltage gain, current gain, and power gain in terms of power delivered to the load, RL. b. Sketch both the DC and AC equivalent circuits. c. Derive the expression for ripple factor of Half Wave Rectification with a capacitor filter.
When the armature circuit resistance increase then the induced e.m.f Ans/ 1/ Increase 2/ Decrease 3/ Remain constant none of the mentioned
Design an AC / DC converter with a ripple factor less than 5% and using a transformer with a 10:1 ratio, starting at 120 Vrms, and with a load resistance of 500 N. Use a rectifier bridge
Create a schematic diagram for building an AC-DC power supply that uses a complete bridge rectifier, filter capacitors, and regulators and has a selectable output voltage (24V) Keep in mind: When a load is attached, the power supply must be able to deliver at least 1A of output current.
the way of working for boost dc-to-dc converter.
Design Half-wave Rectifier Circuit to provide an output of 100 VDC. Then calculate its transformer peak voltage rating, the diode PIV rating, and the transformer turns ratio, if the power is taken from the 220V line AC supply
Ql: For a single-phase full bridge-controlled rectifier. The input supply voltage 220 V, 50 Hz, the firing angle (a=45°), and the load is (R=10 Q). Draw the rectifier circuit diagram and then find the following: a. draw to scale VLoads and ILoad b. comment how the SCR can be turned off? c. Find Vde and Vms for the load voltage.
In this voltage divider bias circuit, the input is at the base. Output is at the emitter with a high input resistance and low output resistance. The maximum voltage gain is 1 and the coupling capacitors must have a negligible reactance at the frequency of operation. (use to answer a and b) a. Derive the expression for the voltage gain, current gain, and power gain in terms of power delivered to the load, R. b. Sketch both the DC and AC equivalent circuits. c. Derive the expression for ripple factor of Half Wave Rectification with a capacitor filter.
Design a circuit for an uncontrolled half-wave Rectifier based transformer step down containing a capacitor filter circuit, with writing the laws of the circuit and the shape of the output wave, with a comparison between the current output wave and the voltage output wave in terms of being affected by the placement of the filter.
Q4. In 1 x 4 demultiplexer, the signals given to the input and selection lines are given in the flowing figure; draw the output waveforms of the demultiplexer. Data in So
2b) A regulator curcuit needs to be designed with an input power supply which has a nominal value of V_PS=20 V and can vary by ± %25 and nominal output voltage of 10 volts. For this purpose a zener diode is employed with specifications given; power rating of 1 W, 10V drop at Iz=25 mA, output load current is to vary between I(subscript L)=0-20 mA and zener resistance of r_Z=5Ω i) If the minimum Zener current is to be I_Z=5 mA, determine the required R_S ii) Determine the maximum variation in output voltage iii) Determine the regulation percent
Biasing in integrated circuit design makes use of what type of DC source? Explain.