write the process of revers osmosis water treatment Techonology?

Q: Parts of Septic tank

A: A home septic tank system consists of underground storage and treatment of wastewater in tanks made…

Q: What are the major thermal factors to consider when selecting a material?

A: Thermal conductivity Thermal conductanceThermal resistanceMelting temperatureHeat capacity

Q: Title A glass ionomer material may be used for all of the following except a(n): a. restorative…

A: A glass isomer material can be used as restorative material, liner and also as lutting agents. If…

Q: There is a brick whose mass is 2625g. Its water content is 5%. Then how much water is absorbed in…

A: Given Brick mass (MB )= 2625 g water content (w) = 5% To Find water absorbed in brick

Q: (1)[1] Ox Ti Add Text Add Picture (b). Home Edit meq/l Comment meq/l Convert [A] Text Box Ca²+ Page…

A:

Q: What are the side effects of Nitrogen oxides (NOx)?

A: Oxides of nitrogen (NOx)

Q: Explain Why don't suggested curing by ponding and polythene sheets?

A: During the process of hydration of concrete, there is a loss of moisture from the concrete which…

Q: Transferring a composite wall and then to an inside air represents heat from outside air to O…

A:

Q: Differentiate between compressible and in compressible fluids.

A: Solution: Compressible fluid is defined as that it is considered  as a matter that can it be…

Q: Explain the process of liquefaction.

A: Soil liquefaction in simple words is when a soil turns into liquid and this can happen as a result…

Q: What are the major thermal factors to consider when selecting a material?

A: The significant thermal variables to consider while choosing a material are  Thermal conductivity…

Q: What are the most frequent contaminants found in indoor air?

A:

Q: What is discharged condensate in condensing systems?

A: Discharged condensate in the condensing system:

Q: How to calculate liquid viscosity of a mixture

A: Given dataquestion is given let's discuss below How calculate liquid viscosity of a mixure

Q: Explain the term ‘Glass transition temperature

A:

Q: Talk about the mechanisms that trap particles in the filter and explain how they are backwashed.

A:

Q: Explain the jet grouting process.

A: Jet grouting is the mostly used method for ground improvement and soil stabilization. This method is…

Q: From what does the Vibratory drivers consists of?

A: A vibratory driver is a device that is used to drive piles into the soil to provide foundation…

Q: Can desalination also be added in the process? And if so, on which part? Thank you

A: Any method that removes excess salts and other minerals from water is known as desalination.

Q: What is an electrostatic precipitator? Explain its working.

A: Electrostatic Precipitator (ESP) An electrostatic precipitator (ESP) eliminates particles from a gas…

Q: what is the meaning of fly ash

A: Flyash is the byproduct of burnt coal in thermal power plants.

Q: What materials are used for vapor retarders?

A: A vapor shield, also known as a vapor diffusion retarder, is a substance that slows down the…

Q: What are the precautions when using ceramic filters?

A: Foundry filters are packed in cardboard boxes that protect them from damage. The filter layers are…

Q: he insulation to be used in a certain slot is as follows: fish paper 3/64 inch, Tufflex 3/32 inch,…

A: Fish paper: 3/64 inchTufflex: 3/32 inchVarniches cambric: 3/64 inchTop stick: 1/8 inchTo find: the…

Q: How does air polluted with particulate matter affect human beings ?

A: Answer Introduction Particulate matter is the matter which consists of the microscopic solid. The…

Q: صنف نموذج التربة ادناه باستخدام طريقة نظام تصنیف آشتو AASHTO method وحسب نتائج الفحص: Percent finer%…

A: Soil characteristics is given. We need to classify the soil as per AASTHO system.

Q: What is the effect of Gas density on the efficiency of a cyclone seperator?

A: Cyclones are centrifugal separators. They transform the inertia force of gas particles to a force…

Q: 4. Using a three-dimensional sketch, show the locations of the air barrier and vapor retarder in a…

A: 4. Using a three-dimensional sketch, show the locations of the air barrier and vapor retarder in a…

Q: What is the function of spray manifold in cyclone spray chamber scrubbers?

A: Solution: The liquid is sprayed from the nozzles on a manifold that has been directed towards the…

Q: What is a unit that is commonly used to express the insulation value ofclothing?

A: The unit that is commonly used to express the insulation value of clothing is :

Q: Domestic Water System

A: it's a broader term describing the overall manufacturing process of breads and buns. It consists of…

Q: What is heat loss calculation in insulated pipes?

A: Heat loss is the amount of energy lost through a pipe of closed media which can be insulated from…

Q: What thermoset plastic is widely used to produce foamed insulation commonly sprayed on roofs and in…

A: Answer The type of plastic widely used to produce foam insulation which is commonly sprayed on roofs…

Q: There are no temperatures limits (heat or cold) in the Regulations for construction. True False

A: True

Q: 1/ Alkalis are harmful ingredient in clay bricks. How? 2/ what is the effect of the following on…

A: As per guidelines we are supposed to answer only first question.

Q: Make a 200-word reflection about making and curing concrete specimen in construction. Also state the…

A: Treatment plays an important role in improving the strength and durability of concrete. The…

Q: What is meant by air-entraining?

A: Entrainment. It is defined as the process in which the movement of one fluid layer will take over…

Q: How are insulation materials rated on their ability to resist heat flow?

A: Rating of the insulation materials:

Q: Please describe the Applications and significance of energy loss in pipe fittings. (Give real life…

A: Energy loss in pipe fittings refers to the reduction of fluid energy due to friction and turbulence…

Q: Discuss the difference between total suction, matric suction and osmotic suction.

A:

Q: What are the three operational considerations that govern the design and manufacture of heat pipes

A: For the manufacturing of heat pipes there are different operations which need to be considered.…

Q: Differentiate each subclasses of glasses, clay products, refractories and carbons. Indicate its…

A: Types and Applications of GLASSES:  The glasses are a familiar group of ceramics;containers, lenses,…

Q: What is the difference between vapor pressure and Henry's Law constant? What is an application of…

A: Answer:- Vapor pressure:-  When a liquid comes in the contact with the air, a fraction of it will go…

Q: Create a step-by-step approach for the computation of the design of a fabric filtering system.

A: Introduction: Fabric filtration is a physical separation method that involves passing gas or…