Write the advantages and disadvantages of gus turbime

Q: To insulate a device against a high external temperature, which of the following are practical…

A: Insulation is the process of surrounding a material by some other material to reduce the escape of…

Q: What is notch sensitivity?

A: Notch sensitivity:- When a material undergoes cyclic or fluctuating lading then in that case notches…

Q: in steel, explain major axis vs minor axis explain this straight to the point

A: To explain: The major axis vs minor axis in steel.

Q: Why is a solid collet safer than a split collet?

A: Solution:

Q: How can the average shear stress be related to the torque?

A: Let us consider an example of a cylinder rotating in viscous fluid with some average shear stress…

Q: Define the term transverse shear?

A: The shear stress which occurs due to bending moments in a body is known as the Transverse shear.

Q: why in a puncture resistance test of woven plain 1/1 fabric, the max elongation decrease as the…

A: For woven plain 1/1 fabric -

Q: Q2 (a) Compare single threaded and multiple threaded screw and state the benefit why it has been…

A: Introduction: Threading is done for fastening two objects or for motion transmission. In swiss…

Q: I need part 10 answered pertaining to the print provided.

A: 10.Refer to the Hex Flange Screw drawing. The ASME standard referenced for drawing interpretation is…

Q: Give an example of the single shear failure?

A: Shear is caused by the action of two opposite and equal forces acting on a material. If the two…

Q: A double acting cylinder is used to transfer work-pieces in a production machine. Both the extend…

A: Given:Force needed, F=3500 NRod diameter, d=15 mm or 0.015 mPressure, P=6 barFriction force=10 % of…

Q: G .l DO o e (iv) Dimensionless film thickness is greater 0 ) 0} ) Question 5: As the temperature is…

A: Lubricants are designed to reduce friction between moving parts as well as the passive resistance of…

Q: Which is not a performance factor of the design of a journal bearing? choose answer below…

A:

Q: In detail discuss what, where and how are counterweights used?

A:

Q: raw a potential to failure curve and explain its characteristics

A:

Q: -0.749 diom -0.561 diam -24 UNF-2A-

A: Based on the information provided, there are two components that failed: the M24 engine mounting…

Q: Explain why intermediate jacks designed in some pipe jacking projects?

A: In the long pipeline, the establishment of frictional forces between the jacking pipe and soil is…

Q: ed? Static of

A:

Q: Differentiate between dry friction and internal friction ?

A: Friction: Friction is the force resisting the relative motion of solid surfaces, fluid layers, and…

Q: What are the mechanical problems are associated with an ESP?

A: Given ESP To find Mechanical problem

Q: What are the procedures adopted to increase the fatigue resistance of: Spindle shaft; Welded joint;…

A: The fatigue resistance of a spindle shaft can be increased by adopting the following…

Q: explain the operational difference between CV joints and universal joints. (50-80 words)

A: What is CV joints? CV joints are the constant velocity joint. Is is used to produduced connection…

Q: Explain the differences between active and passive recovery methods.

A: The recovery after the exercise is very important for our body. There are two types of recovery…

Q: Figure 4 shows a HSS drill bit to be coated with TIN coating using either PVD or CVD coating…

A: Requirment    HSS drill bit to be coated with TiN coating using either PVD or CVD coating process.…

Q: 7. Which one is coarser? (a) Abrasive paper: 180 grit paper or 320 grit paper ANS: (b) ) Metal…

A: Given: Grit is the size sandpaper, used to rating of the sandpaper. The grit ranges from MACROGRITS…

Q: Investigate and describe the different types of fluidization. Mention at least two examples of…

A: Fluidization : In the Fluidization process, The solids are caused to behave like a fluid in terms of…

Q: If pitch circle radius of a sprocket is 14.8 cm and pitch of the chain which can engage with this…

A: Pitch is the distance measured along the circumference of the pitch circle from a point on the tooth…

Q: What material and corresponding stresses is best for HP shape?

A:

Q: What is the difference between kinetic and static friction? 2) What is the effect of static coeffi

A: The difference between the static and kinetic friction is that in case of static friction the object…

Q: Write the difference between damped and undamped vibrations?

A: Answer :-  The difference between damped vibration and undamped vibration has been summarised in…

Q: What is Axial Load and explain with example?

A: Axial load is the load which act on the body parallel to the axis or perpendicular to the…

Q: Consider the variation in performance under mild loads between slotted and pure ALOHA. Find the…

A: To find: The smallest variation in the performance under mild loads between slotted and pure ALOHA.

Q: Name four material properties that affect thermal shock resistance

A: Given Data : Thermal shock resistance

Q: Explain the difference between mean time between failures and useful life

A: Meantime between failures (MTBF) is the anticipated passed time between inborn disappointments of a…

Q: Explain why the actuating devices are simulated before the actual fabrication?

A: Actuating devices: Actuating devices are one which controls any mechanism. When these devices…

Q: Industrial Pipes Is the residual tightening given in screw cases intended to compensate for internal…

A: The objective of the question is to understand the purpose of residual tightening in screw cases and…

Q: Explain in your own words how the load test (performance test) is applied to the patient turning…

A: Medical equipment to find load test ( performance test )

Q: 13. What are the main guidelines for choosing materials in case of sliding wear.

A: Guidelines for choosing materials in case of sliding wear are as follows -  Sliding wear is defined…

Q: Design an experiment to measure the "coefficient of friction μ" (static or kinetic) of a surface…

A: The coefficient of friction is nothing but a numerical value that is used to measure or quantify the…

Q: What are the mechanics of torque tube failure and the failure pattern?

A: It is asked to explain about the failure mechanism in torque tube

Q: Q/Define the stiffness? Discuss the criteria for selection of materials for stiffness

A: The resistance to a force that might otherwise cause a part to bend is known as stiffness. Many…

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.