Write assembly code using the CJNE command that performs the following operation and writes the result to P3. Here, N is the number read from Pl. Assume that the maximum value for N is 22d or 16h. Note: If it is assumed that information will come from any port, no value should be assigned to this port by software. To test the accuracy of the written codes, the relevant port is selected in the Debugger as shown above and the active/passive status in the boxes is changed for the desired value. Thus, it is accepted that value comes to the Port from the outside world. Do not forget that ports are bridges between the physical world and the microcontroller.

Write assembly code using the CJNE command that performs the following operation and writes the result to P3. Here, N is the number read from Pl. Assume that the maximum value for N is 22d or 16h. Note: If it is assumed that information will come from any port, no value should be assigned to this port by software. To test the accuracy of the written codes, the relevant port is selected in the Debugger as shown above and the active/passive status in the boxes is changed for the desired value. Thus, it is accepted that value comes to the Port from the outside world. Do not forget that ports are bridges between the physical world and the microcontroller.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Ex. 1912. A PLC current-input module has a resolution of 9-bits and has a Calculate the digital range of 5mA to 20MA. value for 15.550 mA input, and also current resolution (i.e. mA per A/D count). ans:2
7. Explain in your own words some of the trade-offs between CISC and RISC. Also, explain what an OINC is.
23.a. The down counter stops when the count is 0000.The mode of operation is. b. The down counter sets the maximum count when the count is 0000.The mode of operation is c. In the figure below, The counter starts at count of 1111.As input pulses applied ,the counter will down Applying seven input pulses causes the count to decrease by The count changes to MSD LSD 1111 Down Counter d.What is the ripple counter MOD in figure below? Explain your answer. MSD LSD QA High- D B J J ck Input- >C CLR CLR CLR CLR Clear e. A two flip-flop counter will not work for a MOD of 12 because its highest possible MOD is f. What is the binary count if the counter increments 3 more in the figure below? LSD O MSD B Up Counter
Discuss the importance of integrated circuits (ICs) in modern electronic devices.
QUESTION TWO A single-phase asymmetrical semiconverter feeds an RL load with R = 10 N and a large L so that load current is level. The source voltage is 230 V, 50 Hz. For a firing tingle delay of 30°, determine; (a) average value of output voltage and output current, (b) average and rms values of diode, thyristor and source currents, (c) input power factor and circuit turn-off time.
What is EMI and EMC ? How we take care in case of Electrical Hardware design?
What is the effect of the temperature on the input dc voltage of a pv inverter? Why it is important to regard it during design
Discuss the challenges and limitations associated with miniaturizing microchips and increasing their processing power. How are these challenges being addressed by semiconductor manufacturers?
outline the operation of UJT in power electronics
Discuss the challenges and techniques of power management in battery-operated microcontroller systems.
The output voltage of a single-phase full bridge voltage source inverter is controlled by unipolar PWM with one pulse per half cycle. For the fundamental rms component of output voltage to be 75% of DC voltage, the required pulse width in degrees (round off up to one decimal place) is
Discuss the concept of analog and digital signal processing in microcontrollers and how Microchip's products incorporate these features for various applications.