Write and assemble a program to: a) Set SP to address 0x200 (same technique as we used with RAMEND, divide this address into low and high byte and load them into SPL and SPH) b) Store a different value (use STS) in each of RAM locations $200, $1FF, $1FE, $1FD, $1FC, and $1FB c) POP each stack location into registers R20 – R24. d) Use the simulator to single-step and examine the registers, the stack, and the stack pointer.

Write and assemble a program to: a) Set SP to address 0x200 (same technique as we used with RAMEND, divide this address into low and high byte and load them into SPL and SPH) b) Store a different value (use STS) in each of RAM locations $200, $1FF, $1FE, $1FD, $1FC, and $1FB c) POP each stack location into registers R20 – R24. d) Use the simulator to single-step and examine the registers, the stack, and the stack pointer.

Name: Write and assemble a program to:a) Set SP to address 0x200 (same tech
Uploaded: 2024-03-20T06:51:23.000Z
Channel: Bartleby
Description: Write and assemble a program to:a) Set SP to address 0x200 (same technique as we used withRAMEND, divide this address into low and high byte andload them into SPL and SPH)b) Store a different value (use STS) in each of RAM locations$200, $1FF, $1FE,

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Q2. Interface 4 digit displays (each digit is a 7-segment display) to the 80386DX microprocessor (32 bit data bus and 32 bit address bus) using 8255 PPI. The 8255 should function at I/O addresses that start at 200H. Then write a program to initialize the 8255 and multiplex the 4 digit display where the data, in 7-segment code, that is to be displayed is stored at memory location 2000H: 0100H.
Assume that the integer variables f, g, and h are assigned to registers Ss0, Ss1, and Ss2 respectively. Assume that the base address of integer arrays A and B are in registers Ss3 and Ss4 respectively. Write a MIPS-32 program segment that performs the following C statement: B[g] = A[f] + A[h+2].
Q1- Write a program in assembly language for the 8085 microprocessor to send 10 bytes of data located at the memory address (3000H to 3009H) using SOD at a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz. When sending each of the required bytes, you must adhere to the following: The two high bits of the start bits must be sent, after that the data bits are sent, after that the low bit of the stop bit is sent. The following flowchart will help you, but you should notice that this flowchart deals with one byte, and you are required to deal with 10 bytes. The solution must be integrated and include the calculation of the baudrate delay time Transmit No Set up Character Bit Counter Send Start Bit Wait Bit Time Get Character in Accumulator Output Bit Using Do Wait Bit Time Rotate Next Bit in Do Decrement Bit Counter Is It Last Bit? Yes Add Parity if Necessary • Send Two Stop Bits Return (a)
Q5.Write a multiplication an Intel 8085 assembly program to multiply 2 numbers. The numbers are stored in memory locations 3000H & 3001H. Store the result in memory locations 3002H & 3003H. Show your flow chart and the assembly code. Q6. Answer True or False for the followings: a) Machine code is the assembly code b) Data field is 16 bit while address field is 8 bit c) Trainerkitcanbeused for implementing assembly code d) ADo bus can be used for addressing and datatransfer e) WR and RD pins are on the same pin
Part 1: Preliminary Summarize the difference between binary machine language, assembly language, and high-level source files like C. Contrast the difference between a compiler, assembler, and linker What is the difference between the data segment and the text segment of in an assembly language program? What register is used as the stack pointer? What is a ebreak instruction in the sample program? How would you define a constant named 'BLUE' and assign it to the value OX00F in assembly language? Describe how to implement the psuedo-instruction li t1, e using a native instruction.
Translate trhe following C code to MIPS. Assume that the variables f, g, h, i, and j are assigned to registers $s0, $s1, $s2, $s3, $s4, respectively. Assume that the base address of the arrays A and B are in registers $s6 and $s7, respectively. Assume that the elements of the arrays A and B are 4-byte words: B[8]= A[i] + A[j];
Q1- Write a program in assembly language for the 8085 microprocessor to send one byte of data located at the memory address (3000H) using SOD at a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz. When sending the required byte, you must adhere to the following: The two high bits of the start bits must be sent, after that the data bits are sent, after that the low bit of the stop bit is sent. The following flowchart will help you. The solution must be integrated and include the calculation of the baud rate delay time Transmit Set up Character Bit Counter • Send Start Bit No Wait Bit Time Get Character in Accumulator Output Bit Using Do Wait Bit Time Rotate Next Bit in Do Decrement Bit Counter Is It Last Bit? Yes • Add Parity if Necessary Send Two Stop Bits Return (a)
QuedT: Choose the correct answer: [ Opcode, funct3 and funct7/6 in instruction format are used to identify the: (a) function. (b) instruction. (e) branch. (d) memory address. The register that hold the address of the current instruction being executed is called: (a) saved register. (b) global pointer. (e) stack pointer. (d) program counter. Placing the executable file into the memory for execution by the processor is the role of (a) assembler. (b) linker. (e) loader. (d) compiler. The part which responsible for transmitting the data to/from the processor is: (a) control unit. (b) Datapath. (c) data bus. (d) memory. Parallel hardware cannot be used for faster division because: (a) subtraction is conditional on sign of remainder. (b) multiplication is conditional on sign of remainder. (c) subtraction is conditional on sign of divisor. (d) multiplication is conditional on sign of divisor. we cannot slower the clock cycle to fit the floating-point adder algorithm into one clock cycle…
1. Write a program to store 5 consecutive bytes of data into the data segment. The first data element should be 1 and the data should be stored starting from offset position 10H. 2. Write program to exchange the contents of AL and BL using the stacks. The initial values of AL should have 4CH and BL should have 55H. 3. In the above programs, write the physical addresses of all the segment registers, as well as the logical addresses.
Q1- Write a program in assembly language for the 8085 microprocessor to send one byte of data located at the memory address (3000H ) using SOD at a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz . When sending the required byte, you must adhere to the following: The two high bits of the start bits(1 1) must be sent, after that the data bits are sent, after that the low bit of the stop bit (0) is sent. The following flowchart will help you. The solution must be integrated and include the calculation of the baudrate delay time
Q4/ A- write a program to count number of one's & zero's in a number stored at 0200:0010, use rotate instruction, store the result in the memory location 0200:0011 and 0200:0012 respectively. B- 1. What is segmentation? What are its advantages? How is segmentation implemented in typical microprocessors? 2- What is the difference between near call and far call?
In assembly 68k write the: Initialize the supervisor stack pointer to $8000 Initialize the program counter to $1000 Reserve locations at $2000 to hold your first name only (Joshua) as text and call it NAM Reserve locations at $3000 to store 9 longwords, call it MEM, and write your family name (Kimmich) as a comment Reserve locations at $12400 to store 32-bit unsigned integer variable called RES (to be computed)