Would it be b,d, and c? 2. Which of the following are characteristics of a closed loop control systems? Select all that apply. a) Low sensitivity to changes in system parameters b) Higher accuracy c) Good regulation against disturbances d) Reliability d) Slower response to inputs.

Q: 3. What is harmonic restrain and startup characteristic for differential protection and in which…

A: This protection system is employed to protect alternator, transformer and high rating HT motor.…

Q: What is a simulation ? 1. A software like LabView O2. A dynamic system 3. Another name for Nyquist…

A: Simulation is the modeling of a given circuit or system by using different parameters and components…

Q: 6. Compare and contrast the Closed and Open loop Control System

A: In the given questions we need to discuss about the close loop system and open loop system.

Q: Determine the settings required for a PID controller which gave the process reaction curve shown in…

A:

Q: figure for this system, then explain the following: • Output (Controlled variable) • Input…

A: Block diagram of  control system :

Q: Q2: Consider the following control system K, (1+ 18) For K. = 2, tD = 1 and step change in load…

A:

Q: The following figure represents Host computer Machine PLC a. A machine control system example None…

A: Human machine interface or HMI connects a machine to a device or host.  PLC is programmable logic…

Q: c)What is the role of error detector and feedback in a closed-loop control system?

A: modified control system

Q: SV Difference between synchronous and Asynchronous reset. What should be the behaviour of reset in…

A: To verify a design we write verification module and  test bench to check that it meet specification.…

Q: 17. control can reduce system overshoot of a closed-loop control system. (a) D-mode (b) P-mode (c)…

A:

Q: Explain the use of controllers in Control system. What is proportional controller and with example?

A: Controllers are fundamental part of control systems.  A controller is a device which commands and…

Q: What is synchronization in digital control systems and mention some methods used to achieve it?

A:

Q: 6. List two differences between ideal and practical power switches. Answer:

A: 6. 1. Ideal switch has zero power loss and practical switch has finite power loss.

Q: draw flowchart and explanation of plc solar panel measurement system for this block diagram ?

A: Solution :: Sun based tracker is a mechanized sun powered board that really follows the sun to…

Q: 15.a. An encoder is being used instead of a tachometer in a DC servo system. This system of speed…

A: There are a few questions related to the sensors attached to the machine to measure the speed of…

Q: 3. Solve the analog conversion for 8-bit binary numbers 101011112?

A: According to the question we have to convert the given binary number to analog.

Q: What are the advantages of digital control system?

A: Digital control system have various advantages over analog control system.   1. Binary or discrete…

Q: 2. The voltage sensitivity of the full bridge differential circuit is ( the single arm bridge. A. 2…

A: The question is about sensitivity of full bridge.

Q: Please answer this question. I have also added "Lab 5 To-do Test 1" below.  //LAB5 To-do TEST1:…

A: The given code for the programming of the stepper motor is shown below.1//Enable this code to test…

Q: One of the PID controller anti windup methods   clamping and back calculation methods DC   will…

A: The windup of an integrator is a phenomenon that occurs in PID-feedback controllers and causes…

Q: Which option is correct and why? 2. Which of the following are characteristics of a closed loop…

A: Closed loop control system:- It is designed to maintain the desired output of the system and is also…

Q: Define FACTS and write its necessity and benefits. With neat diagrams, briefly describe different…

A:

Q: (c) The block diagram of a system, with proportional controllers implemented in the primary and…

A: Given Data:A block diagram model of a system with,Primary loop proportional gain = Secondary loop…

Q: System  Adjustment of controller parameters are in software rather than hardware. A. Proportional…

A: In this question we will write about controller...

Q: Explain how poles and zeros are important in a feedback control system and t differences between…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: Describe the role of the process reaction curve ( Figure 3 )and the Ziegler-Nichols PID tuning rules…

A: A curve generated in response to a disturbance to a control system is known as the Process Reaction…

Q: Part C-We have different Micro-controllers which can be operated through Transistors but the major…

A: A microcontroller is basically a small computer on a metal oxide semiconductor integrated circuit…

Q: The Proportional controller requires has the proportional gain constant as 8.63.The input range…

A:

Q: Consider a standard feedback control system where each component is functioning properly. Briefly…

A: (a) For proportional only control the controller output is always proportional to the error signal .…

Q: Industrial Motor Controls 15.a. A discrete input can be which of the following? A. −10–+10 VDC B.…

A: To select correct answer from given options

Q: - Industrial Motor Controls 6.a. Where would be the first place to check if a PLC-controlled motor…

A: A Programmable Logic Controller is abbreviated as PLC. These are used for a programmable variety of…